AUTOXBERT Kia Sportage 2011-2016 Rear Door Outside Molding

Contents

User Manual: Rear Door Outside C Pillar Column Molding

For Kia Sportage 2011-2016

Introduction

This manual provides detailed instructions for the installation, maintenance, and specifications of your new Rear Door Outside C Pillar Column Molding. This product is designed as an aftermarket replacement part for Kia Sportage models manufactured between 2011 and 2016.

Two black rear door outside moldings for Kia Sportage 2011-2016

Figure 1: Rear Door Outside C Pillar Column Moldings

Safety Information and Warnings

  • Aftermarket Part: Please note that this is an aftermarket car part and is not an original car part. It is designed to meet or exceed the specifications of the original equipment.
  • Verify Fitment: Before installation, carefully compare the size (approximately 39cm x 14cm x 2cm) and shape of this molding with your old part to ensure a perfect match.
  • Quality Guarantee: We offer a money-back quality guarantee. If you encounter any issues with the product, please contact your seller immediately for a solution.
  • Always use appropriate personal protective equipment (e.g., gloves) during installation.
  • Exercise caution when using tools to avoid damage to your vehicle's paint or other components.

Specifications

FeatureDetail
Brand NameAUTOXBERT
Item TypeDoor Outside Molding
MaterialPlastic
ColorBlack
Dimensions (L x W x H)Approx. 39cm x 14cm x 2cm
Item WeightApprox. 0.1kg
Reference OEM Number83270-3W000
Placement on VehicleRear Left/Right
OriginMainland China

Setup (Installation Instructions)

Follow these steps carefully to ensure proper installation and fitment of your new molding.

  1. Step 1: Prepare the Area

    Park your vehicle on a flat surface. Thoroughly clean the area on the rear door where the new molding will be installed. Remove any dirt, wax, or old adhesive residue to ensure a strong bond and a flush fit. Use an automotive-grade cleaner and ensure the surface is completely dry before proceeding.

  2. Step 2: Remove the Old Molding

    If the old molding is clipped in, use a plastic trim removal tool to gently pry it off. If it is adhered with tape, carefully pull it away from the door. Take your time to avoid damaging the vehicle's paint. You may need to loosen any internal bolts or fasteners that secure the existing molding.

    Screwdriver prying a plastic cap near a car door seal

    Figure 2: Example of prying a cap, often found covering fasteners for moldings.

  3. Step 3: Test Fit the New Molding

    Before removing any adhesive backing, place the new black plastic molding against the door to verify the alignment and fitment. Ensure it matches the contour of your rear door perfectly and that there are no gaps. This step is crucial for a successful installation.

    Close-up of a silver Kia Sportage C-pillar with the molding in place

    Figure 3: Molding shown in position on a vehicle for fitment check.

  4. Step 4: Install the New Molding

    If the molding has adhesive backing, peel off the protective tape. Align the molding carefully with the mounting position on the door. Press firmly along the entire length of the molding to ensure it is securely attached. If it uses clips, simply align the clips with the corresponding holes and push until they snap into place. Apply even pressure across the entire surface.

    Underside of the molding showing mounting clips and adhesive strips

    Figure 4: Rear view of the molding showing attachment points.

  5. Step 5: Final Inspection

    Run your hand along the edges of the newly installed molding to ensure it is secure and flush with the door. Check for any gaps or loose areas. If any issues are noted, gently press on the affected areas to secure them. Allow adhesive to cure for at least 24 hours before washing the vehicle.

Operating Instructions

This product is a static exterior trim component and does not require any operational procedures after installation.

Maintenance

To maintain the appearance and longevity of your molding:

  • Clean the molding regularly with standard automotive car wash soap and water.
  • Avoid using abrasive cleaners or harsh chemicals that could damage the plastic finish.
  • Inspect the molding periodically for any signs of loosening or damage.

Troubleshooting

  • Molding does not fit perfectly: Double-check that all old adhesive residue has been completely removed from the vehicle surface. Ensure the molding is correctly aligned before applying full pressure. For minor gaps, automotive-grade silicone sealant can be used to secure the edges and improve fitment.
  • Molding feels loose after installation: Re-apply firm, even pressure across the entire molding, especially if it uses adhesive. If clips are used, ensure they are fully seated and snapped into place. If the issue persists, the surface may not have been clean enough during installation, or the adhesive may not have fully cured.

User Tips

  • When removing the old molding, it can be helpful to carefully loosen any internal bolts or fasteners on the car's door panel that might be securing the existing trim. This can make removal easier and prevent damage.
  • If you encounter minor fitment imperfections, a small amount of automotive-grade silicone sealant can be applied along the edges to ensure a secure and flush finish.

Warranty and Support

This product comes with a money-back quality guarantee. If you encounter any issues with the product, such as defects or fitment problems not resolvable through troubleshooting, please contact your seller directly for assistance and a solution.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.