Areyourshop Grille-306-Black

Contents

Automotive Grille Lower Mesh Product Manual

For Audi A4 B8 RS4 Style Refitted Vehicle (2009-2012)

1. Product Overview

This Automotive Grille Lower Mesh is a key exterior and functional component designed for the front-end system of your vehicle. It is installed in the lower part of the front grille, between the front bumper and the engine compartment.

Its primary functions include:

  • Protection: Safeguards engine compartment components like the radiator, condenser, and fan from stones, debris, dust, and other foreign objects.
  • Airflow Guidance: Optimizes air intake efficiency and aids in heat dissipation for the engine and cooling system.
  • Aerodynamic Enhancement: Contributes to improved vehicle aerodynamics by reducing wind resistance.
  • Aesthetic Value: Complements the vehicle's exterior styling, enriching the front-end visual appeal.

Manufactured with high-quality ABS plastic and precision processing, this product strictly adheres to original factory technical standards. It is designed for a perfect fit with the original vehicle's size and contour, offering corrosion resistance, impact resistance, and high-temperature resistance. It is also designed for easy installation.

Front view of Audi A4 B8 with honeycomb fog light grilles installed

Figure 1.1: Front view of the fog light grilles installed on an Audi A4 B8.

Angled view of Audi A4 B8 with honeycomb fog light grilles installed

Figure 1.2: Angled view of the fog light grilles installed on an Audi A4 B8.

2. Applicable Models & Technical Parameters

2.1 Product Composition

  • Core Components: Lower mesh main body (honeycomb grid structure).
  • Auxiliary Components (if applicable): Mounting bracket, fixing clips/screws, sealing strips.

2.2 Technical Parameters

  • Product Name: Automotive Grille Lower Mesh
  • Product Type: Racing Grills
  • Grid Type: Honeycomb grid
  • Installation Position: Lower part of the front grille, between the front bumper and the engine compartment.
  • Material: High-strength ABS plastic (injection molding).
  • OEM NO.: 8KD 807 682, 8KD 807 681

Dimensional Parameters:

Diagram showing dimensions of the fog light grilles

Figure 2.1: Approximate dimensions of the fog light grilles. Lengths are approximately 119cm (46.85") and 121cm (47.64"), with widths of 17cm (6.69") and 23cm (9.05").

  • Length: Approximately 49cm (19.29 inches) per piece.
  • Width: Approximately 14cm (5.51 inches) per piece.
  • Thickness (Mesh Main Body): 1.5mm-3.0mm.
  • Grid Aperture: 5mm-20mm (ensuring ventilation and debris blocking).
  • Weight: 0.3kg-1.5kg (varies by material and size).

Performance Parameters:

  • Corrosion Resistance: ABS plastic offers good chemical corrosion resistance, not prone to fading or deformation.
  • Impact Resistance: Can withstand impact force of 5-10N·m without cracking or deformation.
  • High Temperature Resistance: Working temperature range -40°C to +120°C, no deformation or discoloration.
  • Ventilation Rate: ≥70%, ensuring efficient air intake and heat dissipation.
  • Service Life: ≥8 years under normal use and maintenance.

2.3 Applicable Models & Application Scope

IMPORTANT COMPATIBILITY NOTE:

Compatibility diagram showing that the grilles are only for Standard Version bumpers and not for Sport Version bumpers.

Figure 2.2: This product is compatible ONLY with Standard Version bumpers. It is NOT suitable for S-type, S4, or Sport Version bumpers.

  • Vehicle Models: Audi A4 B8 (2009, 2010, 2011, 2012)
  • Bumper Type: Only applicable to standard bumpers. NOT suitable for S-type or S4 bumpers, or any Sport Version.

Before purchase and installation, please carefully verify that your vehicle is a Standard Version Audi A4 B8 from 2009-2012 and does not have an S-type, S4, or Sport bumper. Refer to the provided photos for visual confirmation.

3. Product Structure & Material Advantages

3.1 Product Overall Structure

3.1.1 Core Component Structure

  1. Lower Mesh Main Body: The core part, featuring a honeycomb grid structure. Made from high-quality ABS plastic. The grid aperture is designed to block foreign objects while ensuring ventilation. Edges are polished and deburred to prevent scratching.
  2. Mounting Bracket (Optional): Installed on the back of the mesh, made of ABS plastic or galvanized steel plate. Enhances stability and ensures firm fixation.
  3. Fixing Clips/Screws: Used to secure the lower mesh. Plastic clips are suitable for snap-in mounting, while stainless steel screws are for bolt fixing. Treated for anti-rust and corrosion resistance.
  4. Sealing Strip (Optional): Made of EPDM rubber, installed on the edge of the mesh. Fills gaps, enhances sealing, prevents water/dust ingress, and protects vehicle paint.

3.1.2 Installation Structure Design

  1. Snap-in Installation: Most models use a snap-in design, utilizing original vehicle snap-in points. Plastic clips on the mesh snap directly into place, requiring no drilling or modification.
  2. Bolt Fixing: For some commercial or special models, bolt fixing is used. The mesh has mounting holes corresponding to the vehicle's original points, secured with stainless steel screws.
  3. Combined Installation: Some models use both snap-in and bolt fixing for quick installation and enhanced stability.

3.2 Material Advantages

3.2.1 Core Component Materials

  • ABS Plastic (Injection Molding): Lightweight, high impact resistance, good toughness, not prone to cracking or deformation. Can be sprayed or electroplated for color matching. Excellent chemical corrosion resistance and long service life.

3.2.2 Auxiliary Component Materials

  • Fixing Clips: High-strength engineering plastic, elastic, not easily broken or deformed. Smooth surface for good compatibility with vehicle body.
  • Fixing Screws: Stainless steel, surface galvanized or chrome-plated for anti-corrosion. High tensile strength, resistant to rust and vehicle vibration.
  • Sealing Strip: EPDM rubber, high temperature and aging resistant, elastic. Provides a tight fit to prevent water/dust and protect paint.

3.2.3 Overall Performance Advantages

  • Perfect Fit & Easy Installation: Designed for precise fit, often requiring no drilling or modification, with installation typically completed in 10-20 minutes.
  • Durable & Reliable: High-quality materials ensure corrosion, impact, and high-temperature resistance, with a service life up to 8 years.
  • Effective Protection: Grid design effectively blocks foreign objects, protecting core engine components and reducing maintenance costs.
  • Aerodynamic & Heat Dissipation Optimization: Ensures good ventilation, guides airflow, aids engine cooling, and reduces wind resistance.
  • Aesthetic Enhancement: Matches original styling, enriches the front-end look, and can be customized.
  • Waterproof & Dustproof: Prevents rainwater and dust from entering the engine compartment, reducing wear and corrosion.

4. Installation & Disassembly

4.1 Pre-installation & Pre-disassembly Preparation

  1. Prepare Vehicle: Park on a stable, flat surface. Engage handbrake and turn off the engine. Clean the front of the vehicle, especially the lower grille and bumper area, removing dust, debris, and oil stains.
  2. Locate Installation Position: Identify the original vehicle's mounting points (snap-in points or bolt holes) for the lower mesh. Check for any obstacles (wires, hoses) that might interfere.
  3. Inspect New Product: Confirm the new lower mesh is intact (no cracks, deformation, scratches, missing parts). Verify that its size, shape, and mounting points match your vehicle model. Check that all auxiliary components (clips, screws, sealing strips) are included.
  4. Pre-installation Treatment: For snap-in installation, check clips for elasticity. For bolt installation, ensure screws match. If a sealing strip is provided, apply it to the mesh edge as marked, ensuring it is secure.
  5. Disconnect Old Mesh (if replacing): Determine the old mesh's fixing method (snap-in or bolt). For snap-in, use a plastic pry bar to gently release it, avoiding metal tools to prevent scratches. For bolt type, use a wrench to remove screws.
  6. Inspect Installation Area: After removing the old mesh, clean the mounting points and surrounding bumper area. Check for damage, deformation, or looseness in snap-in points or bolt holes. Repair any damage before installing the new mesh.

4.2 Required Tools

  • Plastic Pry Bar: For prying and installing, to avoid scratching vehicle paint.
  • Socket Wrench Set & Screwdriver Set (flat-head and cross-head): For bolt-fixing types.
  • Lint-free Cloth & Cleaning Agent: For cleaning surfaces and mounting points.
  • Anti-slip Gloves: To prevent hand slipping, tool scratches, and dirt.
  • Anti-rust Spray (Optional): For bolt holes and snap-in points to enhance corrosion resistance.
  • Double-sided Tape (Optional): For auxiliary fixing if snap-in points are loose.

Note: Installation and disassembly are relatively simple and can be performed by individuals with basic hands-on ability. Handle with care to avoid damage to the mesh or vehicle body.

4.3 Disassembly Steps (Removing Old Lower Mesh)

  1. Confirm Preparation: Ensure the vehicle is fixed, front is clean, and area is clear.
  2. Determine Fixing Method: Check if the old mesh is snap-in or bolt-fixed.
  3. Snap-in Disassembly: Wear gloves, use a plastic pry bar to gently pry the mesh from snap-in points, starting from one end. Avoid excessive force.
  4. Bolt-fixing Disassembly: Use a socket wrench or screwdriver to loosen and remove screws (typically 2-4). Carefully remove the mesh.
  5. Clean Installation Area: Clean mounting points, snap-in points, or bolt holes. Remove dust, oil, and old glue.
  6. Inspect Mounting Points: Check snap-in points for intactness, bolt holes for deformation or rust. Use double-sided tape for broken snap-in points or anti-rust spray for rusted bolt holes.
  7. Dispose of Old Mesh: Discard the old mesh according to environmental regulations.

4.4 Installation Steps (Installing New Lower Mesh)

  1. Pre-installation Treatment: Remove protective film. Check clips/mounting holes. Apply sealing strip if provided, ensuring it's firmly in place.
  2. Align Mounting Position: Hold the new mesh with both hands, aligning it with the lower grille. Ensure clips/holes align with original vehicle points. Adjust for level and contour consistency.
  3. Snap-in Fixing: Press the mesh firmly from the middle outwards until each snap-in point clicks into place. Gently shake to check for looseness and re-press if needed.
  4. Bolt-fixing: Align mesh holes with vehicle bolt holes. Insert and evenly tighten screws with a wrench or screwdriver. Do not over-tighten.
  5. Auxiliary Fixing (if needed): If snap-in points are loose, apply double-sided tape to the back of the mesh at loose positions. If bolt holes are misaligned, adjust position slightly without forcing.
  6. Post-installation Inspection: Gently shake the mesh to check for looseness. Verify alignment with the bumper and check for gaps. Clean the surface with a lint-free cloth.

4.5 Post-installation Check

  1. Check Firmness: Gently pull and shake the mesh. For snap-in, ensure all points are engaged. For bolt-fixed, ensure all screws are tight.
  2. Check Fit Degree: Observe gaps between the mesh, bumper, and grille. Gaps should be uniform (≤2mm), with no deviation or protrusion.
  3. Check Surface Condition: Inspect for scratches, deformation, or damage. Check sealing strip for looseness. Adjust or replace if necessary.
  4. Test Run: Drive at low, medium, and high speeds. Listen for abnormal noise (wind, vibration). After driving, check for looseness or displacement. Recheck and adjust if issues occur.

4.6 Key Installation & Disassembly Notes

  • Avoid Scratching: Use plastic tools (pry bar) during installation/disassembly. Avoid metal tools to protect paint.
  • Gentle Operation: Use gentle force when prying snap-in points. Press evenly to avoid deformation.
  • Ensure Alignment: Accurately align the mesh with mounting points before installation. Avoid forced installation.
  • Do Not Over-tighten: For bolt-fixing, tighten screws evenly without over-tightening to prevent cracking or damage.
  • Clean Area: Ensure mounting points and surfaces are clean to ensure firm installation.
  • Confirm Model: Always confirm the mesh is suitable for your vehicle's specific model, front-end size, and mounting points.

5. Usage Instructions & Functional Requirements

5.1 Basic Functional Requirements

  • Foreign Object Blocking: The grid structure effectively blocks stones, gravel, branches, dust, and other foreign objects from entering the engine compartment, protecting the radiator, condenser, fan, and other core components.
  • Ventilation & Heat Dissipation: The reasonable grid aperture ensures good ventilation, guiding external air into the engine compartment to help dissipate heat and prevent engine overheating.
  • Aerodynamic Function: The grid design reduces wind resistance during driving, improving aerodynamic performance and indirectly reducing fuel consumption.
  • Aesthetic Decoration: Matches the original vehicle's front-end styling, enhancing the visual layering and overall aesthetic sense.
  • Waterproof & Dustproof: Prevents rainwater, dust, and other impurities from entering the engine compartment in large quantities, reducing wear and corrosion of internal components.

5.2 Usage Precautions

  1. Avoid Impact: During driving, avoid collisions with large stones, branches, or other hard objects that could cause deformation, cracking, or detachment of the mesh. Inspect the mesh for damage after any collision.
  2. Regular Cleaning: Clean the mesh surface and grid gaps regularly (every 1-2 weeks) to remove dust, debris, and dirt, preventing blockages that could affect ventilation and heat dissipation.
  3. Avoid Corrosive Agents: Use neutral cleaning agents (e.g., car wash liquid) when cleaning. Do not use strong acid or alkali cleaning agents to avoid corroding the mesh surface and affecting its service life.
  4. Check Regularly: Periodically check the installation firmness, clips/screws for looseness, and sealing strip for detachment. Adjust or replace as needed.
  5. No Modification: Do not cut, bend, or modify the mesh yourself, as this can damage its structure, impair protective and ventilation functions, and potentially cause it to fall off during driving.
  6. Avoid High-Temperature Baking: Do not park the vehicle in direct sunlight for extended periods or use high-temperature tools (e.g., hair dryer) on the mesh, as this may cause deformation and discoloration.

6. Maintenance & Inspection

6.1 Replacement Cycle

  • Normal Service Life: The lower mesh has a service life of 8 years or more under normal use and maintenance conditions.
  • Replacement Scenarios: Replace if cracked, deformed, broken, severely rusted (for metal versions), faded, clips are broken/lost, mesh is blocked and cannot be cleaned, or if the vehicle is overhauled and the mesh is aged.
  • Auxiliary Components: Replace fixing clips/screws if broken, lost, or rusted. Replace sealing strip if aging, cracking, or losing elasticity. Replace mounting bracket if deformed or broken.

6.2 Daily Maintenance & Inspection

Before Each Ride:

  • Check installation status: Ensure the mesh is firm, not loose or shaking. Check clips/screws for intactness.
  • Check mesh surface: Observe for damage, deformation, or blockage by foreign objects. Remove large foreign objects promptly.

Every Week:

  • Clean mesh surface: Use a lint-free cloth and neutral cleaning agent. Use a small brush (e.g., toothbrush) for grid gaps to prevent blocking.

Every Month:

  • Comprehensive inspection: Check installation firmness, clips/screws for looseness/rust. Check mesh for deformation, cracking, or rust. Adjust or replace faulty parts.
  • Clean installation area: Clean around the mesh and mounting points to ensure firmness.

Every 3-6 Months:

  • Anti-rust treatment (metal mesh): Spray anti-rust spray on metal mesh and mounting points.
  • Check grid aperture: Ensure grid is not blocked by dirt; clean thoroughly if necessary.

Every 12 Months:

  • Check aging status: Observe for fading, rusting, or sealing strip aging. Replace if obvious.
  • Inspect mounting points: Check snap-in points or bolt holes for damage, deformation, or rust. Repair or treat to ensure firmness.

Long-term Maintenance:

  • If vehicle is unused for >1 month: Cover front with car cover to protect from dust, debris, sunlight. Clean mesh before reuse.
  • If mesh is removed for long-term storage: Store in a dry, clean, cool place, wrapped in cloth to avoid collision/scratches. Check regularly for intactness.

7. Common Fault Handling & Solutions

Fault Symptom Possible Cause Solution
Lower mesh is loose, shaking during driving
  1. Plastic clips are loose or broken.
  2. Screws are loose or lost (bolt type).
  3. Mounting points are damaged.
  4. Mesh is not aligned with mounting points.
  1. Re-press or replace clips.
  2. Tighten or replace screws.
  3. Repair mounting points (use double-sided tape for auxiliary fixing).
  4. Re-align and re-install the mesh.
Mesh is blocked, affecting ventilation and heat dissipation
  1. Dust, debris, and dirt accumulate in grid gaps.
  2. Large foreign objects (stones, branches) block the mesh.
  3. Mesh has not been cleaned for a long time.
  1. Clean grid gaps with a small brush and neutral cleaning agent.
  2. Remove large foreign objects manually.
  3. Develop a habit of regular cleaning (every 1-2 weeks).
Mesh is deformed, cracked, or broken
  1. Collision with hard objects during driving.
  2. Improper installation (forced installation, over-tightening screws).
  3. Long-term sun exposure or high-temperature baking.
  4. Material aging.
  1. Replace the damaged mesh with a new one.
  2. Install the new mesh according to standard steps, avoiding forced installation.
  3. Avoid long-term sun exposure.
  4. Replace the aged mesh in advance.
Metal mesh rusts (if applicable)
  1. Corrosion by rainwater, salt water, or corrosive cleaning agents.
  2. No regular anti-rust treatment.
  3. Surface anti-rust layer is damaged.
  1. Remove rust with sandpaper, then spray anti-rust spray.
  2. Use neutral cleaning agents, avoid corrosive agents.
  3. Regularly spray anti-rust spray (every 3-6 months).
  4. Replace severely rusted mesh.
Abnormal noise during driving (wind noise, vibration noise)
  1. Mesh is loose, shaking.
  2. Gap between mesh and vehicle body is too large.
  3. Foreign objects stuck between mesh and engine compartment components.
  1. Tighten the mesh, replace loose clips/screws.
  2. Install a sealing strip to fill the gap.
  3. Remove stuck foreign objects, check for mesh damage.

8. Safety Warnings

IMPORTANT SAFETY WARNINGS

  1. Vehicle Stability: Installation and disassembly must be performed when the vehicle is stable and fixed (e.g., handbrake pulled) to prevent sliding and potential injury or component damage.
  2. Driving Safety: Do not disassemble or install the lower mesh while driving or when the vehicle is not fixed. This could cause the mesh to fall off, affecting driving safety and potentially leading to traffic accidents.
  3. Handle with Care: Handle the lower mesh carefully during operation. Avoid collision, deformation, or breakage. Do not use sharp tools to scratch the mesh surface, as this can impair its protective function and aesthetic appearance.
  4. Correct Parameters: Do not use the lower mesh with mismatched parameters (e.g., wrong model, size, mounting points). Incorrect parameters can lead to improper installation, the mesh falling off during driving, and damage to engine compartment components.
  5. Pre-Drive Check: After installation, always check the installation firmness before driving. If the mesh is loose, displaced, or damaged, do not drive. Check and adjust immediately.
  6. Children Safety: Keep children away from the installation area. Prevent children from touching the mesh, tools, or vehicle body to avoid scratches and injury.
  7. Proper Disposal: Used lower mesh, clips, screws, and other components must be recycled according to environmental protection regulations. Do not discard them randomly to prevent environmental pollution and potential safety hazards.
  8. Cleaning Precautions: When cleaning the mesh, do not use high-pressure water to flush the engine compartment directly, to avoid water entering the engine compartment and causing component damage.

9. User Tips

  • Verify Compatibility: Double-check your Audi A4 B8 bumper type. This product is specifically for Standard Version bumpers and will NOT fit S-line, S4, or Sport Version bumpers. Refer to the compatibility image in Section 2.3.
  • Inspect Upon Arrival: Carefully inspect the product for any damage, especially broken mounting clips, immediately upon receipt. Packaging can sometimes be insufficient, leading to transit damage.
  • Installation Ease: Many users find the installation straightforward and a perfect fit for standard B8 models. However, some users have reported minor fitment issues on the driver's side or with clips.
  • Alternative Fastening: If you encounter loose clips or minor fitment issues, consider using additional fasteners like zip ties or automotive-grade adhesive (e.g., windshield glue) to secure the grilles firmly in place.
  • Professional Help: If you are unfamiliar with automotive installations or if your vehicle's mounting points are damaged, it is recommended to seek assistance from a professional automotive technician.

10. Warranty & Support

This product is manufactured to high-quality standards. For any manufacturing defects or issues arising from normal use, please refer to the seller's return and refund policy. Keep your purchase receipt as proof of purchase.

For further assistance or technical support, please contact the seller directly through the platform where the product was purchased.

A PDF version of this manual is available for download: User Manual (PDF)

© 2023 Areyourshop. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.