1. Product Overview
The HAKO 936 Electric Soldering Iron Station is a constant temperature adjustable welding tool designed for household maintenance, DIY projects, and professional use. It features ESD (Electrostatic Discharge) safe design and is compatible with 900M series soldering tips.
2. Safety & Warnings
Read all instructions before use to ensure safety and prevent damage.
- Warning: Keep the device and its cord out of reach of children under 3 years old.
- Wear protective eyewear during operation to prevent eye injury from solder splashes or fumes.
- Ensure good ventilation in the work area to prevent inhalation of flux fumes.
- Ensure the soldering station is properly grounded to prevent static electricity damage to sensitive components and for user safety.
- Do not dry-heat the soldering iron tip for extended periods at excessively high temperatures, as this will accelerate oxidation and reduce tip lifespan.
- Always turn off and unplug the soldering station when not in use or before performing maintenance.
3. Setup Instructions
- Unpack Components: Carefully remove all items from the packaging. Verify that you have the soldering station, 907 handle, soldering iron stand, and power cable.
- Connect Soldering Iron: Plug the 907 soldering iron handle into the designated handle socket on the front of the soldering station.
- Position Stand: Place the soldering iron stand on a stable, heat-resistant surface near your work area. Ensure it is easily accessible for resting the hot soldering iron.
- Power Connection: Connect the power cable to the soldering station and then plug it into a suitable electrical outlet. Ensure the voltage matches the requirements of your specific unit (available in AC220V/50HZ or AC110V/50HZ versions).
- Initial Inspection: Before turning on, visually inspect all connections for security and ensure no damage to the cables or components.
4. Operating Instructions
4.1. Settings and Preheating
- Connect the soldering station to power and turn on the power switch. The pilot lamp will illuminate.
- Set the desired temperature using the temperature adjustment knob. The recommended temperature range is usually 300-380°C.
- For leaded solder, a temperature of 330-370°C is typically used.
- For lead-free solder, a higher temperature of 350-400°C or more may be required.
- Allow the soldering iron to preheat until the indicator light shows constant temperature (usually by turning off or changing color, depending on the model).
4.2. Cleaning and Tinning the Tip
- Before initial use or after cleaning, clean the soldering iron tip on a damp sponge or brass wool.
- Apply fresh solder to the tip, melting a thin layer of tin onto it. This process, known as "tinning," prevents oxidation and improves heat conduction.
4.3. Soldering Operation
- Simultaneously contact the heated soldering iron tip with both the component lead and the PCB pad you intend to solder.
- Heat the joint for approximately 1-2 seconds.
- Feed in the solder wire to the heated joint. The solder should melt and flow smoothly, wetting both the component lead and the pad.
- Once the solder has leveled out and formed a good joint, remove the solder wire first.
- Then, remove the soldering iron tip, allowing the solder joint to cool naturally and solidify.
- After use, re-tin the tip to protect it from oxidation.
5. Maintenance
5.1. Daily Maintenance and Care of the Soldering Iron Tip
- Preventing Oxidation: Avoid dry-heating the soldering iron tip for extended periods at excessively high temperatures, as this accelerates oxidation.
- Cleaning Method: Never use abrasive materials like files or sandpaper to mechanically clean the soldering tip. Always use a dedicated damp sponge or brass wool.
- Removing Oxidation: If the soldering iron tip becomes oxidized and blackened, preventing it from accepting solder, it can often be restored using a special "soldering iron tip revival paste."
- Consumable Replacement: The soldering iron tip is a consumable item. Replace it promptly when surface wear or structural changes cause it to lose its ability to accept solder.
5.2. General Maintenance & Storage
- Cleaning: Turn off and unplug the device before cleaning. Use a soft, lint-free cloth to wipe down the station and handle.
- Storage: Store the soldering station in a dry place at room temperature (15°C - 35°C).
- Long-term Storage: If not used for a long time, ensure the device is stored in a dry, temperature-controlled environment.
6. Troubleshooting
- Iron not heating: Check power connection, ensure the power switch is on, and verify the temperature setting. If the issue persists, the heating element or control board may be faulty.
- Tip not accepting solder (oxidized): Clean the tip thoroughly with brass wool or a damp sponge, then re-tin it with fresh solder. If severely oxidized, use a tip revival paste.
- Inconsistent temperature: Ensure the tip is properly seated. The ceramic heating core or temperature sensor might be malfunctioning.
- Power outlet compatibility: The unit is available in AC220V/50HZ and AC110V/50HZ versions. Ensure your unit matches your local power supply and that you are using the correct plug adapter if necessary.
7. Specifications
| Attribute | Value |
|---|---|
| Model Number | 936 |
| Type | Soldering Station |
| Origin | Mainland China |
| Certification | RoHS |
| Input Voltage | AC220V/50HZ or AC110V/50HZ (model dependent) |
| Power | 60W |
| Temperature Range | 200-480°C |
| Dimensions | 24 x 23 x 10.5 cm |
| Soldering Tip Series | 900M series |
| Heating Core | Ceramic heating core |
| Handle Wire Length | 1.2 m |
| Weight | 1.8 kg |
| Usage | Welding |
8. User Tips
- Tip Compatibility: The station uses 900M series soldering tips. Ensure you have the correct tip shape (e.g., horseshoe, pointed, knife-edge) for your specific soldering task. Pointed tips are generally good for small components, while knife-edge tips are useful for drag soldering.
- Power Adapter: If your local power outlet differs from the station's voltage (e.g., using an AU plug with a 220V unit), ensure you have a compatible voltage converter and/or plug adapter.
- Regular Tinning: Always tin your soldering iron tip before and after use, and periodically during long soldering sessions, to prolong its life and maintain optimal performance.
9. Disposal & Recycling
This symbol indicates that this product should not be treated as household waste. According to the WEEE Directive (2012/19/EU), it must be disposed of at an appropriate electronic waste collection point for recycling to prevent potential negative consequences for the environment and human health.
10. Warranty & Support
For warranty information, technical support, or service inquiries, please contact the manufacturer or your point of purchase. Keep your purchase receipt as proof of purchase.
A user manual in PDF format may be available for download. Please refer to the seller's product page or contact support for the link: View User Manual (PDF)