NovelLife TS101

Contents

NovelLife TS101 Smart Soldering Iron User Manual

Model: TS101

1. Safety Statements

Please read this user manual carefully before using the product. The user manual contains information on safe use, please keep it for future reference. Users can visit our website to learn about the update of the user manual.

1.1 General Safety

  • Please only use power adapter/source specially designed for this product or certified by your country/region (please refer to Power Source Selection for detailed power standards).
  • Do not operate in humid environment.
  • Do not operate in flammable and explosive environment.
  • Please keep the product surface clean and dry.

1.2 Warnings

  • When using TS101, please turn off the power when not in use or left unattended to prevent fire.
  • After the power is turned on, the temperature of the soldering tip in operation will reach 50°C to 400°C (122°F to 752°F), so be careful to prevent burns.
  • Do not soak TS101 in water or use it with wet hands to prevent electricity shock.
  • Do not use DC and USB-C interface at the same time.

1.3 Precautions

  • TS101 controller is composed of precision components, dropping shall be avoided.
  • After 5 minutes of continuous operation at full power above 350°C, or 40 minutes of continuous use, the controller temperature will reach above 50°C.
  • For the first time using, due to the heating of the heating element, soldering tip may generate a light smoke, which is a normal phenomenon.

1.4 Liability Statements

Any special, indirect, incidental or subsequent damage or loss caused by the operation of the product that does not follow the contents of this manual (including but not limited to the operating conditions, warnings, precautions, instruction, etc.), the liability will belong to the user.

The user is responsible for any damage or loss caused by disassembling or modifying the product without permission. Please keep this product in a safe place to prevent children from using this product without being supervised.

2. Product Overview

2.1 Interface and Buttons Introduction

NovelLife TS101 Smart Soldering Iron with accessories including the main unit, soldering tip, USB-C cable, stand, and box.

Figure: NovelLife TS101 Smart Soldering Iron with accessories.

Diagram showing the components of the TS101 soldering iron: Soldering Tip Heating End, Soldering Tip Connection End, Anti-slip Cap, Soldering Tip Insertion End, Ball screw, Button A, Button B, OLED Screen, Ground Screw, USB Type-C interface, DC5525 interface.

Figure: TS101 Soldering Iron Components and Interfaces.

  1. Soldering Tip Heating End
  2. Soldering Tip Connection End
  3. Anti-slip Cap
  4. Soldering Tip Insertion End
  5. Ball screw
  6. Button A (heating, temperature adjustment)
  7. Button B (setting, temperature adjustment)
  8. OLED Screen
  9. Ground Screw
  10. USB TYPE-C interface
  11. DC5525 interface

3. Setup

3.1 Unboxing and Initial Assembly

Video: Unboxing and initial assembly of the TS101 Smart Soldering Iron.

The video demonstrates the unboxing process, showing the TS101 unit, soldering tip, USB-C cable, and other accessories. It also illustrates how to connect the soldering tip to the main unit.

3.2 Installing the Soldering Tip and Connecting Power

  1. Put the anti-slip cap into the front end of the soldering controller, and then insert the soldering tip into the controller.
  2. Fix the ground wire with the ground screw.
  3. Use a USB TYPE-C power cable or a DC power cable to connect the power source with TS101 (the two power supply methods cannot be used at the same time), turn on the power, and follow the instructions on the screen.

Note: After the power is turned on, if TS101 shows "No tip!", it means the soldering tip is not firmly installed. Please re-install the soldering tip.

Usage of Anti-slip Cap:

  • When using the soldering iron, the anti-slip cap can prevent fingers from slipping.
  • Acts as a simple stand to prevent the controller from rolling when placing the soldering iron.
  • Hold the anti-slip cap and push it forward to help remove the soldering tip.

4. Operating Instructions

4.1 Power Source Selection

Smart Soldering Iron TS101 supports two power inputs: DC power source with DC5525 (9-24V) interface (including power adapter, power supply or battery pack, etc.) and PD power source with USB TYPE-C (9V and above) interface (including charger, power bank, etc.).

Diagram showing the TS101 with DC5525 and USB Type C dual power jacks, illustrating connections to a PD charger, laptop power supply, power bank, and drone Lipo battery pack.

Figure: TS101 Dual Power Jack Support with various power sources.

DC Power Source Requirements:

Working VoltageWorking CurrentPowerFastest Heat-up Time (30°C to 300°C)
9V≥1.0A9W95s
12V≥1.3A16W43s
16V≥1.8A30W22s
19V≥2.2A40W15s
24V≥2.8A65W9s

PD Power Source Requirements:

Working VoltageWorking CurrentPowerFastest Heat-up Time (30°C to 300°C)
9V≥1.0A9W95s
12V≥1.4A16W43s
15V≥1.7A25W25s
20V≥2.3A45W15s
28V*≥3.2A90W6s

* For this voltage level, please use a PD3.1 28V power supply and a USB-C power cable supporting 50V 5A 240W EPR. At the same time, set menu PDPwMax as OFF.

4.2 Screen Display and Basic Operations

TS101 screen displaying various settings: 3 preset temperatures (T1, T2, T3), display direction (right/left hand), boost mode temperature, power source selection (DC), and modifiable sensitivity.

Figure: TS101 Screen Display with Settings.

Screen Display Icons:

Screen AreaDisplay ContentDefinition
ACurrent temperature and unitCurrent temperature of the soldering tip
TS101 is in boost mode
BNo displayTS101 is in normal working state
CVoltage value and unitCurrent power source voltage
DSolid lineInstant working power bar, the length of the power bar indicates the ratio of the current instant power to the maximum power
EMTS101 is moving
No displayTS101 is still
FT1/T2/T3Preset temperature T1-T3
zZTS101 is in sleep mode
GNumerical valueCurrent preset temperature

4.3 Parameter Settings

  1. In standby mode, press Button B to enter setting mode.
  2. In setting mode, press Button A/B to select the setting item that needs to be modified. Long press Button A to enter the modification state. Press Button A/B to select the appropriate setting value and wait for 5 seconds after selection. The parameter is successfully modified and will automatically return to setting mode. Other settings can be modified in the same way.
  3. After the setting is completed, long press Button B to save the modification and return to standby mode.
  4. In standby state, long press Button A, TS101 screen will display the current internal resistance of the soldering tip as "Tip R:xx".
  5. In standby state, long press Button B, TS101 screen will display the current firmware version as "Ver:V1.xx".

Note: In standby state, TS101 will enter the off screen state if it stays still for a long time. You can wake it up by shaking the controller to enter standby state.

Parameter Definitions:

ParameterParameter NameDefinitionDefault SettingParameter Range
T1 TempPreset temperature 1System preset working temperature 1300°C: 50~400, °F: 122~752
T2 TempPreset temperature 2System preset working temperature 2330°C: 50~400, °F: 122~752
T3 TempPreset temperature 3System preset working temperature 3350°C: 50~400, °F: 122~752
Temp StepTemperature stepThe stepping of each button operation when adjusting temperature101~25
Sleep TempSleep temperatureStandby temperature in sleep mode, it is recommended to set the value not higher than working temperature250°C: 50~400, °F: 122~752
Sleep TimeSleep Time1. Time needed to enter sleep mode from working mode when controller stays still; 2. Time needed to enter off screen state from standby mode.18060~999, unit: second
Idle TimeIdle timeTime needed to enter from standby mode to sleep mode24060~999, unit: second
BacklightScreen brightnessLED Screen brightness31 to 10; the larger the number, the brighter the screen
TempUnitTemperature unitTemperature display unit°C°C: Celsius, °F: Fahrenheit
Display DirDisplay directionScreen display direction; in different modes, the screen display direction will be reversed, yet the button function will remain unchangedRightRight: right hand mode, Left: left hand mode
BoostTempBoost temperaturePreset working temperature for boost mode (by holding Button A in working mode)380°C: 50~400, °F: 122~752
PowerSrcDC power sourceTypes of DC power sourceDCDC: DC power adapter, 3S~6S: series battery pack
MinVoltUnit minimum voltageMinimum working voltage per cell when powered by a series battery pack35003300~4000, unit: mV
LowCurrentLow current wakeupIn TS101 standby mode, this feature can keep power bank in active stateOFFOFF, ON
PDPwMaxPD power limitMaximum power when using PD power sourceOFF0: OFF, 18~45:18~45, unit: watt
MsenUnitSensitivityAdjust the sensitivity of the internal sensor, the higher the value, the more sensitive31~5
TempCalibTemperature calibrationCalibrate the soldering tip temperature; let the soldering tip cool to room temperature before calibrating
RestoreResetReset

4.4 Heating Operation

  • Heating operation: In standby state, press Button A. TS101 will enter heating working mode. After the temperature is heated to the preset working temperature, TS101 will automatically maintain a constant temperature.
  • Boost operation: In heating working state, hold Button A. TS101 will enter boost heating mode, and the temperature of the soldering tip will rise to the boost heating temperature and maintain a constant temperature. When Button A is released, the temperature will drop back to stay in preset working temperature.
  • Long press Button B in heating mode to return to standby mode.

Note: If the power source voltage is too low, the screen will show "Low volt!", please replace the power source.

4.5 Temperature Adjustment

TS101 has two temperature adjustment methods: select preset temperature or directly adjust temperature.

  1. Select preset temperature: In standby state, press Button A to select preset temperature T1/T2/T3. After selection, TS101 will heat up to the selected preset temperature and maintain a constant temperature.
  2. Direct temperature adjustment: In heating state, press Button B to enter "Work Temp" menu of the working temperature setting, and press Button A/B to adjust temperature (long press A/B for quick adjustment). The setting will be automatically saved and returned to heating mode after 5 seconds of no operation, heated to the set temperature and then keep in the temperature (this modification is valid for one time setting, and will not be saved after power off).

4.6 Sleep and Standby Mode

  • In working mode, if TS101 stays still for 180 seconds (factory default setting, which can be modified by "Sleep Time"), it will enter sleep mode. The "zZ" symbol will appear on the screen, and the soldering tip will cool down to sleep temperature (can be adjusted by the "Sleep Temp").
  • When movement is detected, TS101 will exit the sleep mode and automatically return to working mode, and the soldering tip will heat up to the working temperature before sleep mode.
  • When left still in sleep mode for 240 seconds (factory default setting, can be modified by "Idle Time"), TS101 will return to standby mode. Another 180 seconds in standby mode (factory default setting, can be modified by "Sleep Time"), and the screen of TS101 will turn off.

4.7 Configuration File

  1. Use a USB TYPE-C data cable to connect TS101 to the computer. A virtual disk will appear on the computer, and TS101 will enter USB mode and display "CONFIG" on screen.
  2. Open the CONFIG.TXT file in the virtual disk, and modify the setting parameters (the parameter setting value should be within the adjustable range).
  3. After the setting parameters are saved, they will be updated to TS101 immediately.

5. Maintenance

5.1 Replacing a Soldering Tip

Diagram showing the components of the TS101 soldering iron: Soldering Tip Heating End, Soldering Tip Connection End, Anti-slip Cap, Soldering Tip Insertion End, Ball screw, Button A, Button B, OLED Screen, Ground Screw, USB Type-C interface, DC5525 interface.

Figure: TS101 Soldering Iron Tip Replacement.

  1. Please replace the soldering tip after power off.
  2. Pull out the original soldering tip and reinsert another soldering tip.
  3. Power on again. If TS101 shows "No tip!", it means that the soldering tip is not firmly installed, please reinsert the soldering tip.

Note: The soldering tip insertion end of TS101 controller uses a ball screw to fix the soldering tip, and the tightness of the screw has been adjusted before leaving the factory. If necessary, users can adjust it by themselves.

5.2 Choosing a Soldering Tip

TS101 uses the same soldering tips as the TS100 Mini Soldering Iron. Choosing the right soldering tip can make your job more efficient.

Diagram showing various types of soldering tips for TS101: TS-B2, TS-BC2, TS-C1, TS-C4, TS-D24, TS-I, TS-ILS, TS-K, TS-KU, with their respective dimensions and angles.

Figure: Various Soldering Tip Types for TS101.

5.3 Maintenance of Soldering Tips

  1. When not in use for a long time, it is recommended that the soldering tip be properly tinned to prevent oxidation.
  2. Do not let the soldering tip be heated at a high temperature for a long time to avoid dry burning.
  3. When soldering, do not apply too much pressure on the soldering tip to rub the solder joints to avoid damage to the soldering tip.
  4. Never use rough materials or files to clean the tip of the soldering iron.
  5. If the surface of the soldering tip has been oxidized and does not stick to tin, you can carefully rub it with 600-800 mesh gold steel emery cloth and clean it with ethyl propanol or an equivalent solution as needed, then heat to 200°C, and dip tin immediately to prevent oxidation.
  6. Do not use chlorine or acid-rich flux, only use synthetic resin or activated resin flux.

6. Troubleshooting (FAQ)

QuestionsChecking
No display on TS101 screen after power on
  1. Check power source and cable.
  2. Check if TS101 can enter DFU mode after connecting to the computer and read the virtual disk.
The displayed temperature of the soldering iron jumps around the preset temperature
  1. Is the soldering tip used for the first time or stored in a humid environment? When the soldering tip is fully heated, the temperature can be maintained.
  2. Whether the soldering tip has been installed correctly.
  3. Whether the power cable is in poor contact.
Soldering iron restarts automatically or screen displays "Low Volt!"
  1. Whether the power supply is plugged in and powered on normally.
  2. Whether the power parameters meet the usage requirements.
The screen displays "No tip!"
  1. Whether the soldering tip has been installed correctly.
  2. Whether the soldering tip is in poor contact.
  3. Long press A to check the internal resistance of the soldering tip.
Soldering tip does not stick to tin
  1. Whether the temperature of the soldering tip exceeds 400°C.
  2. Whether the soldering tip is not properly tinned.
  3. Whether there is a lack of flux or using solder with low purity or low tin.
  4. Whether you have ever wiped the soldering tip with a dry sponge or shredded with high sulfur content or dryness?
  5. Whether the tip has come into contact with organic substances such as plastics, silicon (silicon) grease or other chemicals.
When TS101 is powered by a mobile power source, it can be heated normally, but it will shut down after maintaining a constant temperatureSet the "LowCurrent" menu option as "ON".

7. Specifications

7.1 Product Parameters

ParameterValue
Is Smart DeviceYes
OriginMainland China
Dimensions168mm (L 98mm, φ13-16.5mm for controller)
Model NumberMiniware TS101 smart soldering iron TS100 Pine64 Pinecil Upgrade
Controller Weight20g
ScreenOLED (128*32 pixels)
USB InterfaceUSB TYPE-C (for power source and firmware upgrade)
DC InterfaceDC5525
Soldering Tip Sizeφ5.5mm, L about 105mm (different types of soldering tips are slightly different)

7.2 Working Parameters

ParameterValue
Input VoltageDC 9-24V, PD3.0 9-28V
Output Voltage65W(DC), 90W(PD)
Output Temperature50-400 Celsius Degree
Temperature Stability+/-2% (±3% as per manual)
Soldering Tip Resistance to Ground< 2Ω

7.3 Operating Environment

ConditionTemperatureHumidity
Working state+0°C~+50°CHigh: 40°C~50°C 0%~60%RH
Low: 0°C~40°C 10%~90%RH
Non-working state-20°C~+60°C40°C~60°C 5%~60%RH
0°C~40°C 5%~90%RH

8. User Tips

  • Quick Heating: Many users praise the TS101 for its rapid heat-up time, making it efficient for quick tasks.
  • Stable Temperature: The iron maintains a stable temperature, which is crucial for precise soldering work.
  • Portability: Its small size and USB-C power option make it highly portable and convenient for on-the-go repairs, especially for electronics like FPV drones.
  • Quality Tips: The soldering tips are noted for their good quality and performance.
  • Versatility: Excellent for small electronics projects, micro-soldering, and general fixes.

9. Warranty and Support

9.1 After-sales Service

The soldering iron controller has a one-year free warranty service in the case of non-artificial damage. Please contact the dealer for warranty service. Soldering tips are consumables; if there is no quality problem, once used they will not be returned.

9.2 Firmware Update

  1. Visit www.miniware.com.cn and download the applicable soldering iron firmware to the computer.
  2. Hold Button A of TS101 and connect it to the computer via a USB TYPE-C data cable. TS101 enters DFU mode, the screen displays "DFU: 1.05", and a virtual disk appears on the computer.
  3. Copy the prepared .hex firmware to the root directory of the disk. When the firmware suffix changes from .hex to .rdy, disconnect to complete firmware upgrade.
  • FCC Certification: This device complies with the regulation in the 15th part of FCC regulation. Operation is subject to the following two conditions: (1) This device may not cause harmful interference. (2) This device must accept any interference received, including the interference that may cause undesired operation.
  • CE Mark: The CE mark is a registered trademark of European Community. This CE mark shows that the product complies with all the relevant European Legal Directives.
  • UKCA Mark: UKCA (United Kingdom Conformity Assessed) mark is a certification mark for UK conformity. This device complies with the standard testing and certification under British regulations required for electrical and electronic products to enter the British market.
  • Battery Disposal: This product contains batteries and/or recyclable electronic parts. Please do not dispose of the product together with household garbage. Please handle it according to your local laws and regulations.

9.4 Warranty Terms

1. This Product has a 12-month warranty. During the warranty period, if Product fails or is damaged under correct operations, Product can be repaired or replaced for free. If the warranty period is exceeded, certain maintenance cost would be charged.

2. During warranty period, if following occurs, certain maintenance cost will be charged or after-sale service might be even refused:

  • (1) Failure to follow Safety Instructions or User Manual that results in product failure or damage.
  • (2) Product failure or damage caused by unauthorized disassembly, repair or modification.

For more details and updates, please visit www.miniware.com.cn.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.