1. Introduction
The NOPARDE Custom Logo Projection Light is designed for various commercial and decorative uses, including hotel doors, advertising, shop displays, and general commercial applications. This embedded projection lamp offers clear, striking projections of custom logos and patterns, saving space and enhancing visual appeal.
Video: Overview of the NOPARDE Custom Logo Projection Light in various settings.
2. Safety Precautions
- Lamps that are not waterproof should not be installed in places that can get wet outdoors. Damage from outdoor water exposure is not covered by warranty.
- For any product problems, please contact customer service immediately. Do not attempt to disassemble the unit yourself, as disassembly voids the warranty.
- For waterproof lights, ensure the "waterproof fixed iron ring" is securely tightened. Failure to do so may lead to water seepage over time, affecting projection quality.
3. Package Contents
Your package should contain:
- 1 x NOPARDE Custom Logo Projection Light unit
- 1 x Custom GOBO lens (if ordered)
- 1 x LED power driver
4. Setup and Installation
4.1. Luminaire Opening Size
The required opening size for installation varies by lamp style. Please refer to the table below and the diagram for your specific model:

Image: Diagram showing perforation and depth for LQ, PKQ, PDD, and GD models.
| Model | Wattage | Perforation | Depth |
|---|---|---|---|
| LQ | 15-25W | 9cm | 19cm |
| PKQ | 35W | 10cm | 21cm |
| PDD | 35-80W | 10.5-12.5cm | 17-19cm |
| GD | Not specified | 15cm x 12cm | 16-18cm |
4.2. Installation Procedure
Always disconnect the power supply before installation or removal.
- Use appropriate tools to cut a hole in the ceiling according to the corresponding size of the lamp (refer to section 4.1).
- Connect the LED power driver to the power access.
- Vertically insert the spring fasteners at both ends of the lamp into the hole, ensuring they stand up to secure the lamp.
- Once the lamp is securely in place, installation is complete.

Image: Detailed installation instructions showing cutting a hole, connecting power, and securing the lamp.
4.3. Custom Logo (GOBO) Ordering
The projector requires a GOBO lens to display custom logos. Please ensure you purchase the projector and the logo lens together. To customize your logo:
- Purchase the projector and select the desired logo customization option (e.g., one color, 2-3 colors, colorful).
- Send your customized logo files (AI, CDR, JPG, PNG, TIF, PSD formats are accepted) to the provided email address: sales2@noparde.com.

Image: Visual guide on how to order a custom GOBO lens with your projector.
5. Operating Instructions
5.1. Adjusting Projection Clarity
After the light is turned on, you can adjust the definition of the projection:
- Gently twist the lens outwards to adjust focus. Be careful not to drop the lens.
- The projection distance can affect clarity. For optimal results, adjust the focus at your intended projection distance.
- Avoid debugging outdoors during the day, as the projection may not be visible.
5.2. Adjustable Projection Direction
The projection direction can be adjusted by up to 17°, depending on your specific model:
- LQ series (15/25W): Non-adjustable.
- PKQ series (35W): Adjustable from 0 to 15°.
- PDD series (35/55/85W): Adjustable from 0 to 17°.

Image: Diagram illustrating the adjustable projection angles for LQ, PKQ, and PDD series.
5.3. Color Temperature Options
The default color temperature is white light (6000K). Other color temperatures (4000K, 8500K) can be customized upon request. Please consult customer service for custom color temperature options.

Image: Visual representation of 4000K, 6000K, and 8500K color temperatures.
6. Maintenance
6.1. Lens Fastening
After adjusting the projection clarity, ensure you tighten the iron ring around the lens to prevent it from loosening over time.
6.2. Replacing the GOBO Lens
To replace the custom logo (GOBO) lens:
- Disconnect the power supply.
- Carefully unscrew the top half of the light fixture.
- Remove the old GOBO lens from its placement.
- Insert the new GOBO lens.
- Securely re-fasten the top half of the light fixture, ensuring the iron ring is tightened to prevent any movement or water ingress (for waterproof models).
7. Troubleshooting
- No Projection/Light: Ensure the power supply is connected correctly and the LED power driver is functioning. Check all connections.
- Blurry Projection: Adjust the lens by twisting it gently until the image is clear. Ensure the projection surface is within the optimal distance.
- Water Seepage (for waterproof models): Check if the "waterproof fixed iron ring" is securely tightened. If not, tighten it immediately.
- For any other product problems or issues not covered here, please contact customer service for assistance. Do not attempt to disassemble the unit.
8. Specifications
| Feature | Specification |
|---|---|
| Model Number | noparde15w~55w (INS15-105W) |
| Supply Voltage | AC100-240V |
| Input Power | 15-105W |
| Operating Voltage | DC24-36V |
| Working Environment | -40℃ to 60℃ |
| Lamp Diameter | 37mm |
| Light Source | OSram lamp beads |
| Body Material | Aluminum alloy |
| Waterproof Rating | Not waterproof (Indoor use only) |
| Life Span | 50,000h |
| Installation Method | Screw fixed (self-contained) |
| Weight | 0.7-1.2kg |
| Appearance Color | Silver |
| Color Temperature | 4000K-8500K (customizable) |
| Heat Dissipation | Honeycomb |
| Luminous Flux | 2000-82000 |
| Certifications | CE, RoHS |
9. User Tips
- Changing Logos: To change the projected logo, you will need to order a new custom GOBO lens. Follow the same procedure as initial logo ordering (Section 4.3) to send your new design files to customer service. The GOBO lens can then be replaced as described in Section 6.2.
- Optimal Clarity: For the sharpest projection, ensure the lens is clean and free of dust. Adjust the focus carefully after installation and if the projection distance changes.
10. Warranty and Support
For product problems, warranty claims, or any technical assistance, please contact customer service directly. Do not attempt to disassemble the product, as this will void your warranty.
For more detailed information and diagrams, please refer to the official user manual PDF available at: User Manual (PDF)