SPORTARC Bicycle Computer

Contents

SPORTARC Wired Bicycle Computer User Manual

Model: Bicycle Computer

SPORTARC Wired Bicycle Computer

Image: SPORTARC Wired Bicycle Computer with red accents, displaying speed, temperature, and time.

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your SPORTARC Wired Bicycle Computer. This device is designed to enhance your cycling experience by providing essential riding data at your fingertips. Please read this manual thoroughly before use to ensure proper setup and functionality.

2. Product Overview

2.1. Features (19 Functions)

  • Instant Riding Speed Display
  • Single Trip Distance
  • Riding Time
  • Average Speed
  • Maximum Speed
  • Total Mileage (Odometer)
  • Calories Consumed
  • Temperature Display
  • Clock Display
  • Menu Loop Scan Display (Automatic Cycling through functions)
  • Speed Comparison Indicator (+ or -)
  • Sleep Clock Display
  • Maintenance Reminder
  • Wheel Circumference Setting
  • Kilometer (KM) / Mile (MPH) Selection
  • Automatic Wake-up during Riding
  • Battery Replacement Data Storage (up to 20 seconds)
  • Backlight Function (User Selectable)
  • Power Saving Mode (after 300 seconds of no riding)

2.2. Components

Bicycle Computer Components

Image: All components included in the package: bicycle computer head, wired sensor, magnet, cable ties, and a small instruction sheet.

  • Bicycle Computer Head (Main Unit)
  • Wired Sensor
  • Magnet
  • Mounting Base
  • Anti-slip Silicone Pad for Base
  • Nylon Cable Ties (for mounting)
  • Instruction Manual (PDF available: View PDF)

3. Setup

3.1. Battery Installation

  1. Use a coin to open the battery compartment cover on the back of the computer head.
  2. Insert one CR2032 battery with the positive (+) side facing up and the negative (-) side facing down.
  3. Close the battery compartment cover securely.

3.2. Sensor and Magnet Installation

Sensor and Magnet Installation Diagram

Image: Diagram illustrating the correct placement of the sensor on the fork and the magnet on a spoke.

Magnet and Sensor Alignment

Image: Close-up view showing the magnet and sensor aligned with a gap of less than 5mm.

  1. Attach the wired sensor to the lower part of your bicycle's front fork using the provided cable ties. Ensure it is securely fastened.
  2. Attach the magnet to one of the spokes on your front wheel.
  3. Position the magnet so that it aligns with the sensor. The optimal distance between the magnet and the sensor should be less than 5mm.
  4. Rotate the wheel 5-6 times to test if the computer displays speed. If no speed is detected, adjust the magnet's vertical position on the spoke until speed is registered.

3.3. Mounting the Computer Head

Bicycle Computer Mounted on Handlebar

Image: The bicycle computer head securely mounted on a handlebar, showing the display and buttons.

  1. Fix the mounting base to your bicycle's handlebar using the provided cable ties. Place the anti-slip silicone pad between the base and the handlebar for added stability.
  2. Slide the computer head completely into the groove of the mounting base until it clicks into place.
  3. To remove the computer head, press the buckle on the base and slide the head out in the opposite direction of insertion.

3.4. Wheel Circumference Setting

The wheel circumference is the distance your wheel travels in one full rotation, measured in millimeters (MM). Accurate setting is crucial for precise speed and distance readings.

Bicycle Computer Dimensions

Image: Dimensions of the bicycle computer: 60mm height, 45mm width, 20mm depth.

Measurement Methods:

  1. Roll-out Method: Mark a starting point on your tire and the ground. Roll the bicycle in a straight line for one full wheel rotation until the mark on the tire returns to the ground. Measure the distance traveled in millimeters.
  2. Calculation Method: Measure the diameter of your wheel (including the tire) in millimeters. Multiply this value by 3.1416 (π).

Setting Procedure:

  • After battery installation, the unit will default to kilometers. Touch the SET (left) button to select the desired speed unit (KM/H or MPH).
  • Then, the display will show the default wheel circumference (e.g., 2060).
  • Touch the SET (left) button to adjust the flashing digit.
  • Touch the MODE (right) button to confirm the digit and move to the next one.
  • Repeat until the full circumference is entered. For example, if your measured circumference is 1651mm, input '1651'.
  • After confirming the last digit, touch MODE (right) again to save and proceed to the next setting (e.g., maintenance reminder).

Common Tire Size Chart (Circumference in MM):

Tire Size Circumference (MM) Tire Size Circumference (MM)
12 x 1.7593526 x 1 (59)1913
14 x 1.50102026 x 1 (65)1952
14 x 1.75105526 x 1.251953
16 x 1.50118526 x 1-1/81970
16 x 1.75119526 x 1-3/82068
18 x 1.50134026 x 1-1/22100
18 x 1.75135026 x 1.402005
20 x 1.75151526 x 1.502010
20 x 1-3/8161526 x 1.752023
22 x 1-3/8177026 x 1.952050
22 x 1-1/2178526 x 2.002055
24 x 1175326 x 2.102068
24 x 3/4 Tubular178526 x 2.1252070
24 x 1-1/8179526 x 2.352083
24 x 1-1/4190526 x 3.002170
24 x 1.75189027 x 12145
24 x 2.00192527 x 1-1/82155
24 x 2.125196527 x 1-1/42161
26 x 7/8192027 x 1-3/82169
650 x 20C193829 x 2.12288
650 x 23C194429 x 2.32326
650 x 35A2090700 x 18C2070
650 x 38A2125700 x 19C2080
650 x 38B2105700 x 20C2086
700 x 23C2096700 x 25C2105
700 x 28C2136700 x 30C2146
700 x 32C2155700C Tubular2130
700 x 35C2168700 x 38C2180
700 x 40C2200

4. Operating Instructions

The computer has two buttons: SET (left) and MODE (right).

4.1. Basic Navigation

  • MODE Button (Right): Press briefly to cycle through different display functions (e.g., Speed, Distance, Time, Temperature, Clock).
  • SET Button (Left): Used for adjusting values during settings.

4.2. Kilometer/Mile Selection

  • After battery installation, or by pressing both SET and MODE buttons simultaneously for 3 seconds, the KM/H (or MPH) unit will flash.
  • Press SET (left) to toggle between KM/H and MPH.
  • Press MODE (right) to confirm your selection.

4.3. Single Trip Distance (DST) / Riding Time (TM)

  • These functions display the distance and time for your current ride.
  • Range: 0.001 to 9999. When the maximum value is exceeded, it automatically resets to 0.
  • To reset DST and TM: In the DST or TM display mode, press and hold the SET (left) button for 3 seconds.

4.4. Average Speed (AVS) / Maximum Speed (MXS)

  • These functions display the average and maximum speed achieved during your current ride.
  • To reset AVS and MXS: In the AVS or MXS display mode, press and hold the SET (left) button for 3 seconds.

4.5. Total Mileage (ODO) / Calories (CAL)

  • Total Mileage (ODO): Displays the cumulative distance traveled by the bicycle. Range: 0 to 9999. Resets to 0 after exceeding the maximum.
  • Calories (CAL): Estimates the energy consumed during your ride.
  • Setting Initial ODO Value: If the battery is replaced for more than 10 seconds, the ODO will reset to 0. In ODO/CAL mode, press and hold the SET (left) button for 3 seconds to enter ODO setting. You can then input your previous total mileage.

4.6. Temperature Display (TEMP) / Clock (CLOCK)

  • Temperature Display: Shows the current ambient temperature.
  • Clock Display: Shows the current time.
  • Setting Temperature Unit and Clock:
    1. In CLOCK mode, press and hold the SET (left) button for 3 seconds to enter temperature unit selection.
    2. Press SET (left) to toggle between Celsius (°C) and Fahrenheit (°F). Press MODE (right) to confirm.
    3. Next, set the 24-hour or 12-hour format. Press SET (left) to select, MODE (right) to confirm.
    4. Then, set the hour. Press SET (left) to adjust, MODE (right) to confirm.
    5. Finally, set the minute. Press SET (left) to adjust, MODE (right) to confirm.

4.7. Speed Comparison Indicator

  • A "+" symbol in the upper left corner of the screen indicates your current speed is higher than your average speed.
  • A "-" symbol indicates your current speed is lower than your average speed.

4.8. Maintenance Reminder Setting

  • The default maintenance reminder is set to 200 km (or miles).
  • To set: Press and hold both SET and MODE buttons simultaneously for 3 seconds to enter the maintenance reminder setting.
  • Press SET (left) to adjust the value. Press MODE (right) to confirm each digit.
  • When the set mileage is reached, the reminder will flash. To turn it off, press and hold the MODE (right) button for 3 seconds. The reminder will reactivate when the next trip reaches the set mileage.

4.9. Scan Mode (Automatic Loop Display)

  • In scan mode, the screen automatically cycles through single trip distance, riding time, average speed, maximum speed, total mileage, calories, temperature, and clock every 4 seconds.
  • To exit scan mode, briefly press the MODE (right) button.

4.10. Power Saving Mode

  • If no movement signal is detected for 300 seconds, the display will enter power saving mode (screen turns off, but clock remains active).
  • Any movement or button press will restore the full display and functionality.

5. Maintenance

  • Cleaning: Wipe the computer and sensor with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Battery Replacement: Replace the CR2032 battery when the display becomes dim or unresponsive. Follow the battery installation steps in Section 3.1.
  • Protective Film: Ensure the protective film on the screen is removed for optimal display clarity and touch responsiveness.
  • Water Exposure: If the touch area becomes wet (e.g., during heavy rain), wipe off any surface water to prevent automatic function activation or unresponsiveness.

6. Troubleshooting

Problem Possible Cause & Solution
Speed always 0 while riding Magnet and sensor distance/angle is incorrect. Ensure the gap is <5mm and they are aligned.
Speed value doesn't match actual speed Incorrect wheel circumference parameter set. Re-enter the correct value (refer to Section 3.4).
Display slow to react Computer operating below 0°C. Functionality will recover when the temperature rises.
Black screen Exposed to direct sunlight for too long. Place in a dark area for a period to recover.
Dim display Battery is low. Replace the CR2032 battery.
Unresponsive touch Wait 10 seconds and try again. Wipe any surface water from the touch area.
Automatic function activation in heavy rain Water on the touch area. Wipe off surface water.

7. Specifications

  • Type: Wired Bicycle Computer
  • Functions: 19 (Speed, Distance, Time, Temperature, Calories, Clock, etc.)
  • Model Number: Bicycle Computer
  • Stopwatch and Accessories: Temperature Testing Stopwatch
  • Dimensions: 60mm (Height) x 45mm (Width) x 20mm (Depth)
  • Battery Type: CR2032 (Button Cell)
  • Display: LCD with Backlight
  • Origin: Mainland China

8. User Tips

  • Wheel Size Settings: For a 29-inch wheel, a common circumference setting is 2288mm. Always verify with a direct measurement for best accuracy.
  • Backlight: The backlight function is user-selectable. If not immediately obvious, try a long press on one of the buttons or check if it activates automatically in low light conditions.
  • Battery Life: The unit is battery-powered (CR2032) and does not have a USB charging port. Keep a spare battery handy.
  • Intended Use: This device is specifically designed for bicycles and is not suitable for motorcycles or other vehicles due to different wheel sizes and speed ranges.
  • Confirm Settings: After inputting any values (like wheel circumference or time), always remember to press the MODE button to confirm and save your changes.

9. Warranty and Support

For any issues not covered in this manual, or for warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase records for reference.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.