1. Safety Notes
Important Safety Instructions: To Be Read Prior To Operation.
- This appliance can be used by children aged from 8 years and above and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been supervision or instruction concerning use of the appliance in a safe way and understand the hazards involved.
- Children shall not play with the appliance.
- Cleaning and user maintenance shall not be made by children without supervision.
- If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
- WARNING: the drive shall be disconnected from its power source during cleaning, maintenance and when replacing parts.
- The instructions shall state that the A-weighted emission sound pressure level of the drive is equal to or less than 70 dB(A), e.g. by writing LpA ≤ 70 dB(A).
- The mass and the dimension of the driven part shall be compatible with the rated torque and rated operating time.
- The type of driven part the drive is intended for.
- WARNING: Important safety instructions. It is important for the safety of persons to follow these instructions. Save these instructions.
- Do not allow children to play with fixed controls. Keep remote controls away from children.
- Frequently examine the installation for imbalance and signs of wear or damage to cables and springs. Do not use if repair or adjustment is necessary.
- Watch the moving shutter and keep people away until the shutter is completely closed.
- WARNING: Important safety instructions. Follow all instructions, since incorrect installation can lead to severe injury.
- Before installing the drive, remove any unnecessary cords and disable any equipment not needed for powered operation.
2. Specifications
The DOOYA DM25LEU Tubular Motor is designed for the motorization of roller blinds.
| Feature | Description |
|---|---|
| Model Number | DM25LEU |
| Type | Electric Tubular Motor Roller Blind Drive |
| Voltage | DC 5V (Input: 5V/2A) |
| Wattage | 8W |
| Rated Speed | 20rpm |
| Torque (N.m) | 1.1Nm |
| Motor Size | Diameter 25mm |
| Power Supply | Built-in rechargeable battery (Li-ion) |
| Charge Method | USB charging |
| Control Mode | Remote control (RF433 Emitter) |
| Radio Frequency | 433.92MHz |
| Maximum Running Time | 6 minutes |
| Working Temperature | -10°C to +55°C |
| Certification | CE |
| EU LVD Voltage | Low voltage: Below 50Vac or 75Vdc |
| Battery Included | Yes |
For more motor models and specific torque, please refer to the nameplate.


3. Setup
Essential Settings: Steps 1 to 3 must be completed to ensure proper operation.
3.1. Motor Installation
The motor is designed to fit a 38mm tube for roller blinds.
- Cut the drive tube to the required length.
- Ensure the tube edge is clean and burr-free.
- Mount the correct crown and drive adapter on the motor. Make sure the drive adapter fits firmly and the crown rotates freely.
- Align the notches on the crown and drive adapter with the drive tube, then slide and fit the motor into the drive tube. Mount the idler and bracket on both ends.

3.2. Pairing the Emitter (Remote Control)
To pair the motor with the emitter:
- Press the P1 button on the motor for 2 seconds (1 jog, long beep once). The motor is now ready for pairing.
- On the remote control, press P2 (1 beep and 1 jog), then P2 again (1 beep and 1 jog), and finally UP (6 beeps and 1 jog). The motor is now paired with the emitter.
After successful code pairing, delete the original stroke setting and motor running mode speed setting, and restore the factory value.
3.3. Setting Upper and Lower Limits
Initiate Limit Setting:
- Press P2 (1 beep and 1 jog), UP (1 beep and 1 jog), and P2 (4 beeps and 1 jog). The motor is now ready for limit settings.
- Press UP or DOWN once. The motor will run continuously up or down. After pressing the emitter setting button, the motor will jog in the running direction. The limit positions can be set precisely.
Set Upper Limit:
- Press UP to operate the motor to the desired upper position.
- Press STOP once, motor stops running.
- Then press and hold STOP for 3 seconds or press STOP 5 times (5 beeps and 1 jog). The upper limit is set.
Set Lower Limit:
- Press DOWN to operate the motor to the desired lower position.
- Press STOP once, motor stops running.
- Then press and hold STOP for 3 seconds or press STOP 5 times (5 beeps and 1 jog). The lower limit is set.
Note: If there is no further operation within 2 minutes after entering limit setting status, the motor will exit the limit setting status. If the motor is powered off and then powered on, the motor will exit the limit setting mode. If the motor already has a limit, delete the limit before setting.
3.4. Adding a Preferred Position
To set a preferred intermediate stop position:
- Check that both upper and lower limits are set.
- Operate the product to the desired preferred position.
- Press P2 (1 beep and 1 jog), STOP (1 beep and 1 jog), and STOP again (3 beeps and 1 jog). The preferred position is now set.
To delete the preferred position, press STOP for 2 seconds. Repeat the operation to set a new preferred position.
3.5. Pairing Additional Emitters
Normal Addition:
- Press P2 (1 beep and 1 jog) and P2 (1 beep and 1 jog) on an existing paired emitter.
- Press P2 on the new emitter to add (7 beeps and 1 jog). The new emitter is paired to the motor.
Quick Addition:
- Press P1 button on the motor for 2 seconds (1 jog), release button and long beep once.
- Press UP and DOWN on the new emitter to add (7 beeps and 1 jog). The new emitter is paired to the motor.
Note: Normal addition of the emitter needs to be carried out with a limit. After the emitter is successfully added, all the original settings of the motor are retained.
4. Operating Instructions

4.1. Basic Operation (P1 Button)
The P1 button on the motor allows for cycle operation:
- Press the P1 button once: The motor will run upward.
- Press the P1 button again: The motor will stop.
- Press the P1 button again: The motor will run downward.
- Press the P1 button again: The motor will stop.
This cycle repeats with each press.
4.2. Jog Mode & Running Mode Switch
To switch between jog mode (momentary movement) and running mode (continuous movement):
- Press P2 (1 beep and 1 jog), UP (1 beep and 1 jog), and DOWN (2 beeps and 1 jog). The motor will switch to jog mode.
- Repeat the same procedure to switch back to running mode.
Note: When in jog mode, if you press UP or DOWN once, the motor will jog. If you press for more than 2 seconds, the motor will be continuously running.
4.3. Speed Regulation
The motor has adjustable speed settings:
Acceleration Setting:
- Press and hold UP and STOP buttons simultaneously for 2 seconds (2 jogs). The motor speed will be set to Level 2.
- If the motor jogs 3 times, the speed is set to Level 3.
Deceleration Setting:
- Press and hold DOWN and STOP buttons simultaneously for 2 seconds (1 jog). The motor speed will be set to Level 1.
- If the motor jogs twice, the speed is set to Level 2.
Note: If the motor does not respond, it has already reached the maximum or minimum speed.
4.4. Switch Rotating Direction
If the motor runs downward when you press UP, you can switch the direction:
- Turn the DIP switch to "0" and then to "1".
- Repower the motor.
- Press P2 (1 jog), P2 again (1 jog), and DOWN (3 beeps and 1 jog). The direction has been switched successfully.
5. Maintenance
5.1. Charging Instructions
The DM25LEU motor has a built-in Li-ion battery pack with integrated charge management. The maximum power input for recharging is 5V 2A.
- Before first use, please charge the motor for 6 hours. Use a 5V charger (most phone chargers are 5V).
- During operation, the motor will stop running when the voltage is lower than 6.5V and will resume again when the voltage is greater than 6.8V.
- The motor buzzer will sound when the voltage is lower than 8.0V and will resume again when the voltage is greater than 8.2V.
- When the motor is running continuously and the voltage is lower than 7.2V, the buzzer sounds 10 times and the LED light will flash 10 times.


5.2. Rechargeable Battery Status
- Blinking red during operation: Charge the battery.
- Blinking green: Battery is charging.
- Continuously green: Battery is fully charged.
5.3. General Care and Caution
- Never drop, knock, drill, or submerge the motor.
- Keep the power cable in the correct position.
- Do not expose the motor to humid or extreme temperature conditions.
- Do not drill into the motor.
- Do not cut the antenna and keep it clear from metal objects.
- Do not allow children to play with this device.
- If the power cable or connector is damaged, do not use.
- Ensure correct crown and drive adaptor are used.
- Ensure the power cable and aerial are clear and protected from moving parts.
- Cables routed through walls shall be properly isolated.
- Motor is to be mounted in a horizontal position only.
- Before installation, remove unnecessary cords and disable equipment not needed for powered operation.
6. Troubleshooting
| Issue | Possible Causes | Solution |
|---|---|---|
| The motor has no response | Battery in motor is depleted Power failure or incorrect connection Emitter battery is low capacity Radio interference/shielding Out of radio control range | Recharge with compatible AC adaptor. Double check power and cable connections, follow wiring instructions. Replace emitter battery. Check if the antenna on the motor is intact and exposed. Check for possible sources of interference. Try control within closer range. |
| The emitter can't control a single motor | Multiple motors are paired to the same channel | Pair a single motor with the emitter correctly. Consider using multi-channel emitters to control multiple projects, ensuring each channel controls one single motor. |
| The motor doesn't run or starts too slowly or makes loud noise | Connections are incorrect Installation is improper or overload | Check connections. Check installation for proper load and ensure no overload. |
| The motor stops during up and down running | The motor has reached the lower limit The running time is more than 6 minutes | Adjust the new lower limit. Allow the motor to cool down if it has been running continuously for its maximum duration. |
7. User Tips
- Initial Charge: Ensure the motor is fully charged for at least 6 hours before first use to optimize battery life and performance.
- Remote Control Range: If experiencing issues with the remote, try moving closer to the motor. Ensure there are no obstructions or sources of radio interference.
- Motor Compatibility: This motor is specifically designed for 38mm tubes. Verify your roller blind tube size before installation.
- Battery Life: The built-in lithium battery offers convenience. Keep an eye on the blinking red light to know when it's time to recharge.
- Professional Installation: For complex setups or if you are unsure about any steps, it is recommended to have installation and programming performed by a qualified professional to avoid voiding the warranty.
8. Warranty and Support
Incorrect installation can lead to serious injury and will void the manufacturer's liability and warranty. Always follow the instructions carefully.
For detailed information, including additional motor models and specific torque values, please refer to the official user manual PDF: DOOYA DM25LEU User Manual (PDF).
If you encounter any issues not covered in this manual or require further assistance, please contact the seller or a qualified service agent.