1. Safety Warnings
Please read and understand all safety instructions before using the charger. Failure to follow these instructions may result in electric shock, fire, or serious injury.
- This charger is designed exclusively for cylindrical Lithium-Ion (Li-ion 3.70V/3.80V), Lithium Iron Phosphate (LiFePO4 3.20V), Ni-MH/Ni-Cd (1.20V), and 9V Ni-MH rechargeable batteries. Do not attempt to charge other battery types.
- Always refer to the battery manufacturer's recommended charging current and do not exceed it.
- Use only the specified 12.0V DC power adapter with a minimum output current of 4.0A.
- The charger may generate heat during operation. Place it on a heat-resistant surface and keep it out of reach of children and pets.
- Disconnect the power supply and remove all batteries when the charger is not in use.
- For indoor use only, at normal room temperature.
- The data displayed on the charger's LCD screen is for reference only. For precise measurements, use professional instruments.
- Fire Risk: Please be aware of potential fire risks associated with battery charging. Strictly follow the instruction manual for charging and storage procedures.
2. Product Overview
The LiitoKala Lii-S12 is an advanced 12-slot intelligent battery charger designed for versatility and efficiency. It features a microcomputer management system for each slot, allowing for simultaneous charging of various battery types with individual monitoring.

Figure 2.1: LiitoKala Lii-S12 Charger, showing the main unit, power adapter, car adapter, and product packaging.
Key Features:
- 12 Independent Charging Slots: Each slot operates independently, allowing for simultaneous charging of different battery types and sizes.
- Versatile Compatibility: Supports Li-ion, LiFePO4, Ni-MH, Ni-Cd, and 9V Ni-MH batteries.
- Intelligent Charging: Microcomputer control automatically detects battery type (for most cylindrical cells) and configures optimal charging parameters.
- Adjustable Charging Current: Five selectable current levels (0.30A, 0.50A, 0.70A, 1.00A, 2.00A) for cylindrical batteries.
- LCD Display: Provides real-time information including battery type, voltage, current, charging time, capacity, and internal resistance.
- Multiple Safety Protections: Includes overcharge, over-discharge, short-circuit, reverse polarity protection, and intelligent bad battery detection.
- Dedicated 9V Battery Charging: Specific slots for charging 9V Ni-MH batteries.
3. Setup
- Unpack the Charger: Carefully remove the LiitoKala Lii-S12 charger and its accessories from the packaging.
- Connect Power Adapter: Insert the DC plug of the provided 12V/4A power adapter into the DC input port on the back of the charger.
- Plug into Outlet: Connect the power adapter to a suitable AC power outlet.
- Initial Display: Upon power-on, the LCD screen will briefly illuminate all segments for about 3 seconds, then display "null". The indicator lights for each channel will cycle through red and green before turning off, with the green light remaining on for standby.
4. Operating Instructions
4.1 Battery Insertion
Carefully insert rechargeable batteries into any of the 12 available slots. Ensure correct polarity (+ and -) as indicated on the charger slots. The charger is designed to accommodate various cylindrical battery sizes.

Figure 4.1: The charger accommodating various cylindrical battery types (e.g., 18650, AA, AAA) in its slots.
4.2 Automatic Detection and Manual Battery Type Selection
- Automatic Detection: For Li-ion (3.70V/3.80V) and LiFePO4 (3.20V) batteries, the charger will automatically configure the charging current based on the battery's internal resistance upon insertion. For Ni-MH/Ni-Cd (1.20V) batteries, the charging current is fixed at 0.50A and cannot be adjusted.
- Manual Selection (MODE Button): Within 9 seconds of inserting a battery, you can press the "MODE" button to manually select the battery type: Li-ion 3.70V, Li-ion 3.80V (IMR), or LiFePO4 3.20V. This option is not available for Ni-MH/Ni-Cd batteries. During the charging process, you can long-press the "MODE" button to reselect the battery type, but any previously recorded charging data for that slot will be lost.
4.3 Charging Current Selection (CURRENT Button)
- For Li-ion/LiFePO4 Batteries: To change the charging current for a specific slot, first use the "NEXT" or "PREV" buttons to select that channel on the LCD. Then, long-press the "CURRENT" button until the current value on the display starts flashing. Short-press the "CURRENT" button repeatedly to cycle through the available current options: 0.30A, 0.50A, 0.70A, 1.00A, 2.00A.
- Maximum Current Distribution:
- Slots 1, 3, 6, 8 can support a maximum charging current of 2.0A.
- Slots 2, 4, 5, 7 can support a maximum charging current of 1.0A.
- The total charging current between paired slots (1&2, 3&4, 5&6, 7&8) will not exceed 2A. For example, if slot 1 is charging at 2.0A, and a battery is then inserted into slot 2, slot 2 will charge at 1.0A.
4.4 LCD Display Interpretation
The LCD provides comprehensive real-time information about the charging process for each slot.

Figure 4.2: A close-up view of the LCD display, showing battery type, voltage, current, and charge percentage for multiple channels.
- Battery Symbol: Indicates the charge level. During charging, it will show a cycling animation. When full, it will be solid.
- CH (Channel Number): Identifies the specific charging slot (e.g., CH1, CH2).
- Battery Type: Displays the detected or selected battery chemistry (e.g., Li-ion 3.70V, LiFePO4 3.20V, Ni-MH 1.20V).
- Current (A): Shows the active charging current in Amperes.
- Voltage (V): Displays the current voltage of the battery in Volts.
- Time (h): Shows the elapsed charging time in hours.
- Capacity (mAh): Displays the accumulated charge capacity in milliampere-hours.
- Percentage (%): Indicates the estimated charge percentage.
- Internal Resistance (mΩ): Shows the internal resistance of the battery (for reference).
- "null": Displayed when a slot is empty or in standby mode.
- "Err": Indicates an error, such as a short circuit or reverse polarity. Check battery insertion and condition.
- Indicator Lights: Red light indicates charging. Green light indicates standby or fully charged. Flashing red light indicates an error.
4.5 9V Battery Charging
The charger includes dedicated slots for 9V Ni-MH rechargeable batteries. These are typically located on the far left side of the charger (slots C1 and C2, with specific 9V contacts).

Figure 4.3: The charger with two 9V batteries inserted into their dedicated charging contacts.
- Insert 9V Ni-MH batteries into the designated 9V charging contacts.
- The charging current for 9V batteries is approximately 85mA per battery and is not adjustable.
- The LCD screen will not display detailed data for 9V batteries during charging, but the indicator lights will show their status.
5. Maintenance
- Cleaning: Always disconnect the charger from the power source before cleaning. Use a soft, dry cloth to wipe the surface of the charger. Do not use abrasive cleaners, solvents, or immerse the charger in water.
- Storage: When not in use, store the charger in a cool, dry place away from direct sunlight, moisture, and extreme temperatures.
- Handling: Avoid dropping the charger or subjecting it to strong impacts, as this may damage internal components.
6. Troubleshooting
- Charger Not Powering On: Ensure the power adapter is securely connected to both the charger and a working AC outlet. Check if the outlet has power.
- "Err" Displayed: This indicates a short circuit or incorrect battery polarity. Remove the battery, check its condition, and reinsert it correctly. If the error persists, the battery may be faulty.
- Battery Not Charging: Check if the battery is inserted correctly with proper polarity. Ensure the battery is within the charger's supported voltage range (e.g., not completely dead 0V, or between 1.65V-2.20V, which may require trickle activation).
- Charger Becomes Warm: It is normal for the charger to become warm during operation, especially when charging multiple batteries at higher currents. Ensure adequate ventilation around the charger. If it becomes excessively hot, discontinue use and contact support.
- Inaccurate Readings: The LCD display provides approximate values for reference. For precise measurements of battery capacity or internal resistance, use dedicated testing equipment.
7. Specifications

Figure 7.1: The bottom of the charger displaying detailed input, output, and compatibility specifications.
| Feature | Specification |
|---|---|
| Input Voltage | DC 12.0V 4.0A (minimum) |
| Output Voltage (Li-ion) | DC 4.20V |
| Output Voltage (IMR) | DC 4.35V |
| Output Voltage (LiFePO4) | DC 3.65V |
| Output Voltage (Ni-MH/Ni-Cd) | DC 1.48V |
| Output Voltage (Ni-MH 9V) | DC 9.0V |
| Output Current (Li-ion/IMR/LiFePO4) | 2.00A x 4 (slots 1/3/6/8 only), 0.30A/0.50A/0.70A/1.00A x 8 |
| Output Current (Ni-MH/Ni-Cd) | 0.50A x 8 |
| Output Current (Ni-MH 9V) | 85mA x 2 |
| Cut-off Current | 100mA |
| Standby Current (no load) | <50mA |
| Compatible Li-ion/IMR/LiFePO4 | 26650, 21700, 20700, 18650, 18490, 18350, 17670, 17500, 16340 (RCR123), 14500, 10440 |
| Compatible Ni-MH/Ni-Cd | AA, AAA, SC, C |
| Dimensions (L x W x H) | 195.0mm x 142.5mm x 35.0mm |
| Weight | 800g (excluding power cable) |
8. User Tips
- Faster Charging: For the quickest charge, utilize single slots or ensure only one battery is charging in a paired slot (e.g., slot 1 or 2, but not both simultaneously at 2A). This allows for higher current delivery to individual cells.
- Reliable Detection: Users report that the charger generally detects battery types accurately and effectively prevents overcharging, contributing to battery longevity.
- Charge Level Indication: While the charger provides a good indication of the current charge level and voltage, it does not typically display the final accumulated capacity (mAh) after the charging cycle is complete.
9. Frequently Asked Questions (FAQ)
- Q: Does this charger come with an American plug?
A: The charger typically comes with a standard power adapter suitable for your region. Please check the product packaging or seller details for specific plug types included with your purchase. - Q: Are batteries included with the charger?
A: No, batteries are not included with the LiitoKala Lii-S12 charger. This product is a charger only, and batteries must be purchased separately.
10. Warranty & Support
For detailed warranty information, technical support, or service inquiries, please refer to the manufacturer's official website or contact your original point of purchase. Keep your purchase receipt as proof of purchase.