CooSpo BK9

Contents

CooSpo BK9 Series Cycling Sensor User Manual

Dual Bluetooth 5.0 & ANT+ Speed and Cadence Sensor

1. Introduction

This manual provides detailed instructions for the CooSpo BK9 series cycling sensors, including the BK9C Cadence Sensor and BK9S Speed Sensor. These sensors utilize both Bluetooth 5.0 and ANT+ wireless technologies to connect with various cycling apps and bike computers, providing accurate data for your rides.

CooSpo BK9 Cadence Sensor and Speed Sensor side-by-side
Figure 1: CooSpo BK9 Cadence Sensor (left) and Speed Sensor (right).

2. Package Contents

Please check the contents of your package. If any items are missing or damaged, contact customer support.

2.1. BK9C Cadence Sensor Package

  • CooSpo BK9C Cadence Sensor x1
  • User Manual x1
  • Cadence Silicone Pad x1
  • Silicone Strap x2
CooSpo BK9C Cadence Sensor packaging and accessories
Figure 2: Contents of the BK9C Cadence Sensor package.

2.2. BK9S Speed Sensor Package

  • CooSpo BK9S Speed Sensor x1
  • User Manual x1
  • Speed Silicone Pad x1
  • Silicone Strap x2
CooSpo BK9S Speed Sensor packaging and accessories
Figure 3: Contents of the BK9S Speed Sensor package.

3. Setup and Installation

Before installation, ensure you remove the transparent insulation sheet from the sensor's battery compartment. This activates the sensor.

Diagram showing removal of transparent insulation sheet from sensor battery
Figure 4: Remove the transparent insulation sheet before use.

3.1. Cadence Sensor (BK9C) Installation

  1. Install the silicone pad on the back of the sensor.
  2. Select the Silicone Strap that best fits the thickness of your bike's crank arm.
  3. Install the cadence sensor on the inner side of the left crank arm.
  4. Turn the crank to ensure that the cadence sensor and Silicone Strap do not rub against the bike frame or your shoes during operation.
Diagram showing installation of cadence sensor on a bike crank arm
Figure 5: Cadence sensor installation on the left crank arm.

3.2. Speed Sensor (BK9S) Installation

The speed sensor is typically installed on the wheel hub.

  1. Install the silicone pad on the back of the sensor.
  2. Select the Silicone Strap that best fits the thickness of your bike's wheel hub.
  3. Install the speed sensor securely on the wheel hub.
  4. Ensure the sensor is firmly attached and does not interfere with any moving parts of the wheel or fork.
Diagram showing installation of speed sensor on a bike wheel hub with dimensions
Figure 6: Speed sensor installation on a wheel hub. Dimensions: 1.2 inch (height), 1.3 inch (width), 0.3 inch (thickness), weight 8.4g.

4. Operating Instructions

4.1. Pairing with Cycling Apps (Bluetooth)

  1. Turn on Bluetooth and location services on your smartphone.
  2. Important: Do not pair the sensor directly through your phone's Bluetooth settings. The sensor should be paired within the cycling application.
  3. Open your preferred cycling app (e.g., CoospoRide App).
  4. Navigate to the Sensor Settings Menu within the app (e.g., "More" > "Sensors" > "Add Device").
  5. Find the BK9C/BK9S Bluetooth ID in the app's list of available sensors and select it to connect.

4.2. Pairing with Smart Devices (Bluetooth and ANT+)

This applies to bike computers and other compatible smart devices.

  1. On your smart device, select "Add Sensor" from the settings menu.
  2. The device will search for available sensors. Find the BK9C/BK9S Bluetooth or ANT+ ID in the list and select it to connect.

4.3. Sensor Wake-Up

The sensor will enter sleep mode after a period of inactivity to conserve battery. To wake it up before pairing or use, simply turn the wheel (for speed sensor) or crank (for cadence sensor) a few rotations.

5. Function and Indicator Status

The sensor uses an indicator light to communicate its status:

Sensor Status Indicator Light
Battery Installed Red and Blue Alternately Flashing
Wake Up Blue Light Flashing
Low Battery Alert Red Light Flashing

6. Specifications

Feature Detail
Model BK9C / BK9S
Battery Type CR2032, 3V
Battery Life 300H (hours)
Wireless Transmission Bluetooth 5.0; ANT+
Waterproof Rating IP67

Note: The actual battery life may vary depending on usage environment and conditions.

7. User Tips

  • Ensure the sensor is securely installed to prevent loss or damage during your ride.
  • Always wake up the sensor by rotating the crank or wheel before attempting to pair it with an app or device.
  • If experiencing pairing issues, double-check that Bluetooth and location services are enabled on your phone, and try pairing directly within the cycling app, not through the phone's system settings.
  • Replace the CR2032 battery promptly when the red light flashes to ensure continuous data tracking.

8. Troubleshooting

  • Sensor not detected:
    • Ensure the transparent insulation sheet has been removed.
    • Rotate the crank/wheel to wake up the sensor (blue light should flash).
    • Check that Bluetooth and location services are enabled on your phone/device.
    • Attempt to pair within the cycling app or smart device's sensor settings, not the general Bluetooth settings.
    • Verify the battery is correctly installed and not depleted (check for red light flashing).
  • Inaccurate readings:
    • Ensure the sensor is securely mounted and not moving during your ride.
    • For cadence, ensure it's on the left crank arm. For speed, ensure it's on the wheel hub.
    • Check for any obstructions or rubbing against other bike parts.
  • Short battery life:
    • Battery life can vary with usage and environmental conditions. Ensure you are using a fresh CR2032 battery.
    • The sensor automatically enters sleep mode when inactive to conserve power.

9. Maintenance

  • Cleaning: Wipe the sensor with a soft, damp cloth. Do not use abrasive cleaners or solvents.
  • Battery Replacement: When the red light flashes, replace the CR2032 battery. Carefully open the battery compartment, replace the old battery with a new one, ensuring correct polarity, and securely close the compartment.
  • Storage: Store the sensor in a cool, dry place when not in use for extended periods.
  • Inspection: Periodically check the silicone pad and strap for wear and tear, replacing them if necessary to ensure secure mounting.

10. Warranty and Support

For more information regarding product support, warranty details, or to view the full user manual PDF, please visit the official CooSpo website:

www.coospo.com

A PDF version of the user manual is available for download from the manufacturer's website. The information in this manual is for reference and may be subject to alteration without prior notice due to ongoing product development.

11. Regulatory Information

11.1. FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) this device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

11.2. IC Warning (Innovation, Science and Economic Development Canada)

This device contains licence-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada's licence-exempt RSS(s). Operation is subject to the following two conditions:

  1. This device may not cause interference.
  2. This device must accept any interference, including interference that may cause undesired operation of the device.

L'émetteur/récepteur exempt de licence contenu dans le présent appareil est conforme aux CNR d' Innovation, Sciences et Développement économique Canada applicables aux appareils radio exempts de licence. L'exploitation est autorisée aux deux conditions suivantes:

  1. L'appareil ne doit pas produire de brouillage;
  2. L'appareil doit accepter tout brouillage radioélectrique subi, même si le brouillage est susceptible d'en compromettre le fonctionnement.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.