1. Introduction
This manual provides essential information for the safe and effective use of your new LED Atmosphere Foot-Well Lights for Tesla Model 3, Y, S, and X. These lights are designed to enhance your vehicle's interior ambiance, providing bright and energy-efficient illumination for foot-wells, door puddles, and trunk areas. Please read all instructions carefully before installation and use.
2. Safety & Warnings
Important Safety Information: Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Keep the device and its cord out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult.
- Do not use this product for purposes other than its intended use.
- Inspect the product before each use; do not use if damaged.
- Follow installation and operation guidelines to avoid injury.
- Do not expose to water or moisture.
3. Package Contents
Please check the package for the following items:
- LED Atmosphere Foot-Well Light(s) (Quantity may vary based on purchase option: 1, 2, 4, or 8 units)
Note: The exact quantity of lights included depends on the specific purchase option.
4. Specifications
| Attribute | Value |
|---|---|
| Product Name | Car Ambient Light Strip |
| Model | FCS-18-26 |
| Compatibility | Tesla Model 3, Model Y, Model S, Model X (Trunk Light, Frunk Light, Puddle Light, Foot Well Lights, Glove box light) |
| Special Features | With wires for easy installation, Plug-and-Play, Smart SMD (6 Pcs High power LED chips) |
| Voltage | 12 V |
| Power | 1.8 W |
| Color Temperature | 6000K (White), also available in Blue, Red, Pink |
| LED Lamp Beads | 6 pieces per unit |
| Luminous Flux/Brightness | 200 LM |
| Item Weight | 0.05 kg |
| Material | LED, ABS |
| Package Dimensions (L x W x H) | 11 cm x 8 cm x 1 cm |
5. Setup & Installation
The LED Atmosphere Foot-Well Lights are designed for plug-and-play installation, making the process straightforward. They are a direct replacement for the factory dim lights in compatible Tesla models.
Installation Steps:
- Before First Use: Remove any protective films from the device.
- Carefully Pry the Original Lights: Use a suitable prying tool to gently remove the existing factory light unit from its housing.
- Remove the Original Lights: Disconnect the wiring from the original light unit.
- Connect the Car Cable to the New Light Connector: Plug the car's existing wiring harness into the connector of the new LED light unit.
- Install the New Lights: Carefully push the new LED light unit back into the original position until it clicks securely into place.
6. Operation
These LED lights are designed to function as a direct replacement for your vehicle's existing interior lights. They will illuminate when the corresponding original light would normally turn on (e.g., when doors open, or when the car's interior lights are activated).
The product description mentions "4 Colors" and "Smart SMD" which suggests color options. If your specific model includes a separate controller or has integrated color-changing functionality, refer to its specific instructions for changing modes or colors. Otherwise, the lights will operate in a single, fixed color as selected during purchase.
After Use:
The lights will turn off automatically when the vehicle's interior lighting system deactivates. Store any unused lights in a dry place and keep them away from children.
7. Maintenance
- Cleaning: Use a soft, dry cloth to clean the light units. Avoid abrasive cleaners or solvents that could damage the plastic or LED components.
- Inspection: Periodically check the lights for any signs of damage or loose connections. Ensure they are securely seated in their housings.
- Storage: If removing the lights for any reason, store them in a cool, dry place away from direct sunlight and extreme temperatures.
8. Troubleshooting
- Lights not turning on:
- Ensure the connectors are securely plugged in.
- Verify that the car's interior lighting system is active.
- Check for any visible damage to the light unit or wiring.
- Confirm compatibility with your specific Tesla model and light location.
- Flickering lights:
- Check for loose connections.
- Ensure the vehicle's electrical system is stable.
If issues persist, contact customer support for further assistance.
9. User Tips
- Easy Installation: Users have noted the installation process is easy due to the plug-and-play design and included wiring.
- Quality Assurance: The product is generally well-received for its quality and adherence to description.
10. Compliance Information
This product has received an Attestation of Compliance, Certificate No. HUT20029631-26, indicating conformity with relevant standards, including the Council Directive 2014/30/EU (EMC Compatibility). The CE mark is affixed to the product, signifying compliance with essential European health, safety, and environmental protection requirements.
11. Manufacturer Information
Manufacturer: Shenzhen maggie color technology co., ltd.
Address: No. 202 no. 9, xinle street, pinghu street, longgang district, shenzhen city, guangdong province, China.
Contact: 86-18028619586, 1783705019@qq.com
EU Authorized Representative: SUCCESS COURIER SL
Address: CALLE RIO TORMES NUM. 1.PLANTA 1, DERECHAOFICINA 3, Fuenlabrada, Madrid, 28947 Spain.
Contact: 34-910602659, successservice2@hotmail.com
Importer: Shenzhen maggie color technology co., ltd.
Address: No. 202 no. 9, xinle street, pinghu street, longgang district, shenzhen city, guangdong province, China.
Contact: 86-18028619586, 1783705019@qq.com