VaneAims FXB38

Contents

FXB38 Series Control Switches Product Manual

Detailed instructions for installation, operation, and maintenance.

1. Product Overview

This manual is applicable to all products in the VaneAims FXB38 series, including rotary switches, push button switches, mushroom push button switches, emergency stop button switches, LED push button switches, and LED double-button switches. It provides detailed product parameters, usage instructions, and key term explanations to help users correctly install, use, and maintain the products.

FXB38 Series Push Button Switches in various colors

Figure 1: FXB38 Series Push Button Switches in various colors.

2. Key Term Explanation

2.1. Momentary (Auto-Recovery) vs. Latching (Auto-Lock) Buttons

  • Reset (Momentary) Button: Press this button to turn on the power (e.g., light on); Release your hand, and the power will turn off automatically (e.g., light goes out).
  • Self-locking (Latching) Button: Press the power button, release your hand, and the button remains stationary (e.g., lit); Press the button again to turn off the power (e.g., light goes out).

2.2. Definition of NO and NC Contacts

  • NO (Normally Open): The default state between the two terminals is disconnected. When the button is actuated, the circuit closes.
  • NC (Normally Closed): The default state between the two terminals is connected. When the button is actuated, the circuit opens.

3. Setup and Installation

WARNING: Disconnect the power supply completely before installation to avoid electric shock.

3.1. Installation Steps

  1. Ensure the power supply to the circuit where the switch will be installed is completely cut off.
  2. The installation opening diameter for FXB38 series switches is 22mm, compatible with standard industrial control panels. Prepare the appropriate mounting hole.
  3. Disassemble the switch components as shown in the exploded view (Figure 2).
  4. Insert the button head through the mounting hole from the front of the panel.
  5. Secure the button head with the mounting nut from the rear of the panel.
  6. Attach the contact block to the button head assembly. Ensure it clicks securely into place.
  7. Proceed with wiring according to the circuit diagram and desired operation type.
Exploded view of FXB38 Push Button Switch components

Figure 2: Exploded view of FXB38 Push Button Switch components for assembly.

3.2. Wiring

Strictly follow the NO/NC terminal markings for wiring. Incorrect wiring can lead to misoperation or damage. Refer to the specific wiring diagram for your application.

FXB38 Push Button Switch with contact block detail

Figure 3: Close-up of the contact block showing '1.NC 3.NO' terminal markings.

4. Operating Instructions

The operation of the FXB38 series switches depends on their type (Momentary or Latching) and contact configuration (NO or NC).

  • Momentary Switches: The switch activates only while pressed and returns to its default state upon release.
  • Latching Switches: The switch maintains its activated state after being pressed and released, and requires another press to return to its default state.
  • NO Contacts: The circuit is open by default and closes when the button is pressed.
  • NC Contacts: The circuit is closed by default and opens when the button is pressed.

4.1. Specific Switch Types

  • Push Button Switches: Used for general ON/OFF control.
  • Mushroom Push Button Switches: Often used for emergency stop functions due to their larger, easily accessible head.
  • Emergency Stop Button Switches: Designed for immediate shutdown in critical situations, typically latching with a mushroom head.
  • LED Push Button Switches: Include an integrated LED for visual indication of the switch state.
  • LED Double-Button Switches: Combine two functions (e.g., start/stop) with LED indicators in a single unit.
FXB38 Series Mushroom Push Button Switch

Figure 4: Example of FXB38 Series Mushroom Push Button Switches.

FXB38 Series Emergency Stop Button Switch

Figure 5: Example of FXB38 Series Emergency Stop Button Switch.

FXB38 Series LED Double-Button Switch

Figure 6: Example of FXB38 Series LED Double-Button Switch.

5. Maintenance

To ensure optimal performance and longevity of your FXB38 series switch, follow these maintenance guidelines:

  • Environment: The product is suitable for industrial control environments. Avoid using it in high temperature, high humidity, corrosive gas, or other harsh environments.
  • Cleaning: Regularly wipe the switch surface with a clean, dry cloth to remove dust and debris. Do not use abrasive cleaners or solvents.
  • Inspection: Periodically check for any signs of physical damage, loose connections, or wear on the button head and contact block.

6. Troubleshooting

If you encounter issues with your FXB38 series switch, consider the following:

  • Switch Not Activating/Deactivating:
    - Check all wiring connections to ensure they are secure and correctly terminated according to NO/NC markings.
    - Verify that the power supply to the switch is active and within the specified voltage range.
    - Confirm that the correct operation type (momentary or latching) is being used for the intended function.
  • Intermittent Operation:
    - Inspect for loose internal connections or damaged contacts. (Requires professional inspection).
    - Ensure the operating environment is within the recommended conditions (temperature, humidity).
  • LED Indicator Not Working (for LED switches):
    - Check the voltage supply to the LED. Ensure it matches the specified voltage for the LED (e.g., 12V, 24V, 220V, 380V AC/DC).
    - Verify the LED wiring is correct.

For complex issues or internal component problems, it is recommended to consult a qualified electrician or contact customer support.

7. Specifications

AttributeSpecification
Brand NameVaneAims
Model NumberFXB38
Item TypeSWITCHES
Switch TypePush Button Switch
MaterialPlastic
Current Rating (Ith)10A
Rated Insulation Voltage (UI)440V
EU LVD VoltageBelow 50Vac or 75Vdc
Opening Diameter22MM
Contact Type1NO1NC
Terminal Quantity4
Operation TypeMomentary / Latching
Head Color OptionsRED, BLUE, YELLOW, WHITE, GREEN, BLACK
FeaturesPush button switch without light, button without fixation, button with fixation, power button
Is Smart DeviceNo
OriginMainland China
High-concerned chemicalNone
Package Dimensions (L x W x H)15cm x 15cm x 15cm
Package Weight0.056 kg
FXB38 Push Button Switch dimensions

Figure 7: Product dimensions for the FXB38 Push Button Switch.

8. User Tips

  • Verify Operation Type: Always double-check if you have a momentary or latching switch before wiring to ensure it performs as expected in your application.
  • Color Coding: Utilize the available head colors (Red, Green, Yellow, Blue, White, Black) to visually differentiate functions in complex control panels.
  • Pre-planning: Before installation, plan your wiring carefully, especially for NO/NC contacts, to avoid rework and ensure safety.

9. Warranty and Support

For detailed product guides and documents, please refer to the official user manual PDF: FXB38 Series User Manual (PDF).

For special voltage, color, or other customized requirements, please contact VaneAims customer service in advance to confirm feasibility and delivery time.

Contact Information:
Email: chenmaike3303@sina.com
Mobile/Wechat/Skype: +86 15058777695
Address: zone, Yueqing, Zhejiang, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.