GEYA GTS8-W

Contents

GEYA GTS8-W TUYA WIFI Smart Time Relay Switch Instruction Manual

Model: GTS8-W | Brand: GEYA

1. Introduction

The GEYA GTS8-W Intelligent WiFi Time Switch is designed for smart control of household electrical equipment. It allows for periodic and regular switching of loads, such as lights and appliances, enhancing convenience and energy efficiency in your smart home.

This device supports remote control via the Tuya Smart App, manual operation, and advanced timing functions including countdown, sunrise/sunset, and circulatory timing.

GEYA GTS8-W 2P and 4P WiFi Intelligent Switches

Image: GEYA GTS8-W 2P and 4P WiFi Intelligent Switches.

2. Safety Information

Caution:

  • The products must be installed by qualified electricians.
  • All electrical connections of the time relay shall comply with the appropriate safety standards.
  • Ensure the phone is connected to a 2.4GHz WiFi network during setup. If your router uses a 2.4G/5G intelligent switching mode, temporarily turn off the 5G signal to avoid connection issues.

Disposal of Electrical Waste:

All electrical waste should be disposed of in compliance with current WEEE regulations.

3. Specifications

Below are the technical parameters for the GEYA GTS8-W WiFi Intelligent Switch:

Parameter2P Model4P Model
FunctionWiFi intelligent switch
Rated supply voltageAC220VAC220V(L-N)
Rated frequency45~65Hz
Rated operational current (AC1)32A, 40A, 50A, 63A, 80A63A, 80A
BurdenAC max. 3VA
WIFI connectivity802.11 b/g/n 2.4GHz
Electrical life (AC1)1x104
Mechanical life1x106
Operating temperature-20°C to +55°C (-4°F to 131°F)
Storage temperature-35°C to +75°C (-22°F to 158°F)
Mounting/DIN railDin rail EN/IEC 60715
Protection degreeIP40 for front panel/IP20 terminals
Operating positionany
Overvoltage categoryIII.
Pollution degree2
Dimensions82 × 36 × 68mm
Weight130g370g

Panel Diagram

The panel features a WiFi signal indicator, a switch indicator, and an ON/OFF button for manual control and configuration.

Panel diagram of GTS8-W 2P and 4P models showing indicators and button.

Image: Panel diagram of GTS8-W 2P and 4P models showing WiFi signal indicator, switch indicator, and ON/OFF button.

Dimensions (mm)

Physical dimensions of the 2P and 4P models.

Dimensions of GTS8-W 2P and GTS8-W 4P models, showing front and side views with measurements.

Image: Dimensions of GTS8-W 2P and GTS8-W 4P models, showing front and side views with measurements.

4. Installation

The GTS8-W switch is designed for DIN rail mounting (EN/IEC 60715).

Wiring Diagram

Refer to the following diagram for proper electrical connection. Ensure all connections are made by a qualified electrician and comply with safety standards.

Wiring diagram for GEYA GTS8-W 2P and 4P WiFi intelligent switches, showing connections to AC220V power, a circuit breaker, and a load.

Image: Wiring diagram for GEYA GTS8-W 2P and 4P WiFi intelligent switches, showing connections to AC220V power, a circuit breaker, and a load. For 2P, N and L are connected to the switch, then to the load. For 4P, N, L1, L2, L3 are connected to the switch, then to the load.

5. Setup: Networking and App Configuration

5.1. Install App

To control your GEYA GTS8-W switch, you need to install the Tuya Smart App.

  • Scan the QR code below to download the Tuya Smart App.
  • Alternatively, search for "Tuya Smart" in your device's App Store (iOS) or Google Play Store (Android) and download the App.
QR code for downloading the Tuya Smart App.

Image: QR code for downloading the Tuya Smart App.

5.2. Add Device

When using the device for the first time, or if you need to restore it to factory condition, follow these steps:

  • Press and hold the power button on the switch for 5 seconds.
  • The device will enter the distribution network state, and the WiFi indicator will start flashing.
  • Open the Tuya Smart App on your phone.
  • Click the "Add Device" button and follow the prompts in the App to complete the device addition.
  • Once added, the main interface of the App will display the device icon, and the WiFi indicator on the device will be solid on.

Visual representation of the device in distribution network state:

Diagram showing the WiFi indicator flashing for distribution network state and solid for online status.

Image: Diagram illustrating the device's status indicators: Offline (no WiFi indicator), Distribution network (WiFi indicator flashing), and Online (WiFi indicator solid).

5.3. Connect WiFi

  • Ensure your phone is connected to a 2.4GHz WiFi network.
  • If your router has a 2.4G/5G intelligent switching mode, temporarily disable the 5G signal.
  • Follow the App prompts to connect the device to your WiFi network.

5.4. Reconfigure WiFi

If you need to reconfigure the WiFi connection for the device:

  • If you no longer use this device, you can delete it from the App, and it will restore its factory settings. You can then add it again through the App.
  • Alternatively, press and hold the power button on the device for 5 seconds at any time. The device will re-enter the WiFi configuration state, allowing you to add it again through the App.

6. Operation

6.1. Manual Control

You can manually control the ON/OFF state of the connected load directly using the button on the equipment. The ON/OFF indicator shows the current status.

Diagram showing the manual ON/OFF button and indicator on the switch.

Image: Diagram illustrating the manual ON/OFF button and indicator on the switch. A red indicator means the load is connected (ON), and a white indicator means the load is disconnected (OFF).

6.2. Remote Control via Tuya App

Once the device is successfully added to the Tuya Smart App and connected to WiFi, you can control it remotely.

  • Open the Tuya Smart App.
  • Select your GTS8-W switch from the device list.
  • You can turn the load on and off remotely through the App interface.

Demonstration of remote control:

Video: A demonstration of connecting the GEYA GTS8-W switch to the Tuya Smart App and controlling a light bulb remotely, including setting a countdown timer.

6.3. Timing Functions

The Tuya Smart App allows you to set various timing schedules for your switch:

  • Countdown: Set a timer for the device to automatically turn on or off after a specified duration.
  • Sunrise/Sunset: Program the device to turn on or off automatically before, during, or after local sunrise or sunset times. This is particularly useful for outdoor lighting or street lights.
  • Circulatory Timing: Configure the device to turn on/off repeatedly during a set period, with customizable open and close durations.

These timing functions can be accessed and configured within the "Time" or "Setting" sections of the device interface in the Tuya Smart App.

7. Maintenance

  • Keep the device clean and free from dust. Use a dry, soft cloth for cleaning.
  • Avoid exposing the device to extreme temperatures or humidity outside its specified operating and storage ranges.
  • Do not attempt to disassemble or repair the device yourself. Refer to qualified personnel for any servicing needs.

8. Troubleshooting

  • Device not connecting to WiFi:
    • Ensure your phone is connected to a 2.4GHz WiFi network.
    • If your router has a 2.4G/5G intelligent switching mode, temporarily disable the 5G signal.
    • Make sure the WiFi indicator on the device is flashing (distribution network state) before attempting to add it in the App. If not, press and hold the power button for 5 seconds to re-enter this state.
    • Check your WiFi password for correctness.
  • Device not responding to App commands:
    • Verify that the device's WiFi indicator is solid on, indicating a stable connection.
    • Check your phone's internet connection.
    • Ensure the App is updated to the latest version.
  • Timing functions not working correctly:
    • Double-check the timing settings within the Tuya Smart App for accuracy (start/end times, days of the week, open/close durations).
    • Ensure the device has a stable WiFi connection.

9. User Tips

  • Reliability: Users have noted the GEYA GTS8-W's reliability compared to other brands.
  • Programmability: The device offers robust programming options through the Tuya Smart App, allowing for complex scheduling.
  • Advanced Integration: For advanced users, the device's compatibility with the Tuya ecosystem may allow for integration with other smart home platforms or custom solutions like Arduino, though direct Arduino control is not officially supported and may require advanced knowledge.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact GEYA directly. You can find their contact details below:

  • Email: sale@cngeya.com
  • Web: www.geya.net
  • Address: Wenzhou Bridge Industrial Zone, Beibaixiang Town, Yueqing, Zhejiang, China 325603

Please retain your purchase receipt for warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.