Infitary Multi-Socket LED Car Headlight

Contents

Infitary Multi-Socket LED Car Headlight User Manual

Model: Multi-Socket LED Car Headlight

1. Introduction

Thank you for choosing Infitary LED Car Headlights. This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your new LED headlights. Please read this manual carefully before installation and use to ensure proper function and safety.

2. Product Features

  • High Brightness: Utilizes imported LED chips, providing several times higher brightness compared to traditional halogen lamps.
  • Energy Saving and Environmental Protection: Significantly lower power consumption than traditional halogen lamps, resulting in a much longer lifespan.
  • Plug and Play: Designed for compatibility with the original vehicle circuit, eliminating the need for circuit modifications. (Note: Some vehicle models may require a decoder for optimal performance).
Infitary LED Headlight product packaging and two LED bulbs

Figure 1: Infitary LED Headlight product packaging and two LED bulbs.

3. Lamp Bead Explanation

For dual beam LED car headlights such as H4/9003/HB2, 9004/HB1, 9007/HB5, and 9008/H13, a portion of the LED beads illuminates during low beam operation, while another portion activates for high beam. Certain car models may activate more LED beads during high beam for enhanced visibility.

4. Setup (Installation)

4.1. General Installation Steps

  1. Turn off the vehicle power and allow the headlights to cool down completely.
  2. Dismantling Old Lights: Open the engine compartment, locate the rear cover of the headlights, turn it counterclockwise, and remove the original car light bulb.
  3. Install LED Light: Insert the LED light into the original light socket. Pay close attention to the positive and negative directions, ensuring the buckle is securely in place. Refer to the specific diagrams below for details.
  4. Debugging Lighting: After powering on, verify that the lighting is normal and adjust the lens angle to meet the regulatory illumination range (low beam tangent level).

4.2. Installation Diagrams

The installation process may vary slightly depending on the bulb type. Please refer to the relevant diagram for your specific bulb socket type.

Type: H11 / 9005 / 9006 / 9012 / 880

  1. Open the front cover of the vehicle and prepare to install the LED headlights.
  2. Locate and unscrew the original car bulb.
  3. Remove the original car bulb.
  4. Place the LED bulb in its original position.
  5. Twist the LED bulb until it fits and is secure.
  6. Connect the power supply and test if it is working properly.
Installation diagram for H11/9005/9006/9012/880 type headlights, showing steps to open cover, remove old bulb, insert new LED bulb, and secure.

Figure 2: Installation steps for H11/9005/9006/9012/880 type headlights.

Type: H1 / H3 / H4 / H7 / H13 / 9004 / 9007

  1. Open the front cover of the vehicle and prepare to install the LED headlights.
  2. Locate the original bulb.
  3. Open the spring clip, take out the original bulb and chuck.
  4. Install on the new chuck.
  5. Press the spring clip and make it firm.
  6. Aim at the chuck slot, put the bulb into the chuck.
  7. Ensure the chuck slot matches the convex position.
  8. Rotate slightly to fix the bayonet.
  9. Connect the power supply and test if it is working properly.
Installation diagram for H1/H3/H4/H7/H13/9004/9007 type headlights, showing steps to open cover, remove old bulb, insert new LED bulb, and secure.

Figure 3: Installation steps for H1/H3/H4/H7/H13/9004/9007 type headlights.

4.3. Installation Precautions

  • Ensure the vehicle is in park or securely in gear.
  • Confirm that the ignition is turned off and keys are removed.
  • Exercise caution to avoid burns, especially when turning the vehicle's lighting on or off.
  • Avoid touching the lamp bead with your fingers to prevent staining or damage. Do not press the fan to avoid damage.
  • Pay attention to positive and negative connections. Thoroughly examine the connection of contact points, ports, and wires, as faulty connections can cause lighting problems.
  • Ensure that the end of the bulb does not contact the interior light shield of the headlight when adjusting. The wires of the lights should face downwards.
  • It is recommended to install a dust cover to protect the headlights and extend their service life.
  • If the light does not work after installation, try reversing the plug 180° and reconnecting.

5. Operating Instructions

Once installed, operate your LED headlights by using your vehicle's standard headlight controls. Ensure proper alignment and functionality as described in the installation steps.

Video 1: Demonstration of Infitary LED headlight beam patterns (low beam, high beam) and clarity on a dark road, highlighting 6500K cool white light, 200M clear vision, and good light shape with clear tangent.

6. Maintenance

  • Avoid prolonged continuous lighting. Intermittent shutdown is recommended if usage exceeds 4 hours.
  • Check the cooling fan for dust accumulation every 6 months and clean if necessary to ensure optimal heat dissipation.
Diagram illustrating fast heat dissipation through aviation aluminum and high-quality electrothermal separation copper substrate.

Figure 4: Fast heat dissipation mechanism.

7. Troubleshooting

  • Flickering or Error: Ensure you have chosen the correct socket type for your vehicle. If flickering or errors occur, it may be due to current differences. Since energy-efficient LED headlights require less current than halogen or xenon lamps, installing a pair of decoders may be necessary to resolve the problem.
  • No Light After Installation: Try reversing the plug 180° and reconnecting.
  • Voltage Stability: In case of flicker or extinguishing, prioritize checking whether the vehicle voltage is stable at the appropriate standard voltage (12V or 24V).

8. Specifications

Attribute Value
Brand NameInfitary
Wattage80W/pair
Color Temperature6500K (Cool White)
Voltage12 V
Lumen20000LM
Light Source1860 Chip
Car Brand CompatibilityMost Of The Car
Car Model CompatibilityMost Of The Car
OriginMainland China
CertificationCE
Item TypeOther (LED Car Headlight)
Applicationautomobiles, kit, auto, car led light, lampada, for Kia hyundai audi opel ford volvo benz bmw
Package Length15 cm
Package Width13 cm
Package Height6 cm
Package Weight0.28 kg

8.1. Physical Dimensions

Diagram showing 400% luminance increase over halogen, with dimensions (1.51in, 1.18in, 1.57in), aviation-grade aluminum fuselage, 360-degree adjustable mounting ring, and 12,000RPM silent turbofan. Also shows LED vs Halogen beam patterns.

Figure 5: General dimensions and comparison with halogen lamps.

Mini design diagram showing the compact size (30.2mm / 1.19inch heat sink) compared to a car key, indicating easy installation and no effect on original construction.

Figure 6: Mini design for easy installation, showing 30.2mm heat sink.

Detailed dimensions for various socket types: H7 (39.5mm/1.55inch, 30.2mm/1.19inch, 39.8mm/1.56inch), H4 (47.6mm/1.87inch, 25.4mm/1inch, 39.8mm/1.56inch), H1 (37.6mm/1.48inch, 35.3mm/1.39inch, 11mm/0.43inch, 39.8mm/1.56inch), H11 (40.5mm/1.60inch, 30.8mm/1.21inch, 39.8mm/1.56inch).

Figure 7: Detailed dimensions for H7, H4, H1, and H11 socket types.

9. User Tips

  • For some vehicles, especially those with limited space, the bulbs with integrated fans might be slightly long. You may need to modify or shape the dust cover (e.g., with a heat gun) to ensure it doesn't interfere with the fan when reinstalled.
  • The control module might also occupy space in tight areas, so plan accordingly during installation.

10. Frequently Asked Questions (FAQ)

Q: Are these LED lamps compatible with my car model?
A: The headlights are designed for most car brands and models. However, compatibility can vary. Please ensure you select the correct socket type (e.g., H7, H4, H11, H1, 9005, 9006, HB3, HB4, 9003, HB2, 9004, HB1, 9007, HB5, 9008, H13) for your vehicle. If you are unsure, consult your vehicle's manual or a professional.
Q: What if the lights flicker or show an error?
A: Flickering or errors can sometimes be caused by current differences. Since these LED headlights draw less current than halogen or xenon lamps, installing a pair of CANBUS decoders may be necessary to resolve the issue. Also, check that your vehicle's voltage is stable (12V or 24V).

11. Warranty and Support

This product comes with a 1-year warranty from the date of purchase.

For detailed user guides and documents, including a PDF version of the user manual, please refer to the official documentation available at User manual (PDF).

For further assistance or warranty claims, please contact Infitary customer support.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.