HLTNC HLTNC DC Switching Power Supply

Contents

HLTNC DC Switching Power Supply User Manual

Models: S-Series, LRS-Series, RSP-Series, SMBC-Series, SML-Series, AS-Series, DR-Series, MDR-Series, EDR-Series, NDR-Series, SMV-Series, SD-Series, SMJ-Series, PSP-Series

1. Introduction

This manual provides essential information for the safe and efficient use of your HLTNC DC Switching Power Supply. Designed for a wide range of applications, this power supply offers stable and reliable DC output from various AC input voltages. Please read this manual thoroughly before installation and operation.

2. Safety Information

Always observe the following safety precautions to prevent injury or damage to the device:

  • Ensure the power supply is connected to a grounded outlet.
  • Do not operate the unit in wet or damp conditions.
  • Avoid exposing the unit to direct sunlight or high temperatures.
  • Ensure proper ventilation to prevent overheating.
  • Disconnect power before making any connections or adjustments.
  • This device operates at low voltage (below 50Vac or 75Vdc) but improper handling can still be dangerous.
  • The product is CE certified, indicating compliance with European safety standards.
  • It is also RoHS compliant.

3. Product Overview

The HLTNC DC Switching Power Supply is a robust unit designed for various industrial and hobbyist applications. It features a metal casing with ventilation slots and a cooling fan (on some models).

HLTNC Switching Power Supply
Figure 3.1: HLTNC Switching Power Supply
HLTNC Switching Power Supply views
Figure 3.2: Front, Side, Top, and Bottom Views of the Power Supply

3.1. Components and Controls

The power supply features a terminal block for input and output connections, and a potentiometer for fine-tuning the output voltage.

Terminal block and potentiometer on HLTNC Switching Power Supply
Figure 3.3: Terminal Block and Potentiometer

Terminal Block Labels:

  • L: AC Input (Live)
  • N: AC Input (Neutral)
  • ✉ (Ground wire symbol): Ground connection
  • -V: DC Output (Negative pole)
  • +V: DC Output (Positive pole)
  • +V ADJ: Potentiometer for output voltage adjustment (typically ±10%)

3.2. Internal Circuitry (for reference)

The internal design includes various components for stable power conversion:

Internal circuit board components of HLTNC Switching Power Supply
Figure 3.4: Internal Circuit Board with Labeled Components
  • Package transistor
  • 100UF electrolytic capacitor
  • Pure copper transformer
  • Pure copper inductance coil
  • Rectifier bridge
  • Brand filter
  • Safety capacitor
  • Low voltage capacitor
  • Terminals

3.3. Applications

This power supply is suitable for a variety of applications:

Application scenarios for HLTNC Switching Power Supply
Figure 3.5: Application Scenarios (3D Printers, CNC Machines, Textile Machines, Cutting Machines)

Applications include 3D printers, CNC machines, textile machines, and cutting machines.

3.4. Product Video

Video 3.1: Product demonstration of the HLTNC Switching Power Supply.

4. Specifications

The HLTNC DC Switching Power Supply is available in various models with different output voltages and power ratings. Key specifications are detailed below. Please refer to the specific model for exact values.

4.1. General Specifications

  • Type: Power Supply
  • EU LVD Voltage: Low voltage: Below 50Vac or 75Vdc
  • Rated Capacity: ≤1000VA
  • Output Current: 0-100A (varies by model)
  • Output Frequency: 50/60HZ
  • Output Type: SINGLE
  • Certification: CE
  • Origin: Mainland China
  • Package Dimensions: Length 18cm, Width 10cm, Height 5cm
  • Package Weight: 0.95 kg

4.2. Model-Specific Specifications

Below are tables detailing specifications for various series and models. Note that values may vary slightly between different production batches or specific configurations.

S-Series (e.g., S-500, S-350, S-250, S-400)

Specifications for S-500-12, S-500-24, S-500-36 models
Figure 4.1: S-500 Series Specifications

S-500 Series (Partial Data):

ModelDC Output VoltageOutput Voltage ToleranceRated CurrentOutput Current RangeOutput PowerRipple and Noise
S-500-1212V±1%40A0-40A480W100mVp-p
S-500-2424V±1%20A0-20A480W150mVp-p
S-500-3636V±1%14A0-14A504W150mVp-p
Specifications for S-350-12, S-350-24, S-350-36, S-350-48 models
Figure 4.2: S-350 Series Specifications

S-350 Series (Partial Data):

ModelDC Output VoltageRated CurrentCurrent RangeRated PowerRipple and NoiseVoltage Adjustment Range
S-350-1212V29A0-29A348W150mVp-p10-13.2V
S-350-2424V14.6A0-14.6A350.4W150mVp-p20-26.4V
S-350-3636V9.7A0-9.7A349.2W240mVp-p32-40V
S-350-4848V7.3A0-7.3A350.4W240mVp-p41-56V
Specifications for S-250-12, S-250-15, S-250-24, S-250-36 models
Figure 4.3: S-250 Series Specifications

S-250 Series (Partial Data):

ModeDC Output VoltageRated CurrentOutput Current RangeOutput PowerWave and Noise
S-250-1212V20A0-20A240W150mVp-p
S-250-1515V17A0-17A255W150mVp-p
S-250-2424V10A0-10A240W150mVp-p
S-250-3636V6.9A0-6.9A248W150mVp-p
Specifications for S-400-5, S-400-12, S-400-24 models
Figure 4.4: S-400 Series Specifications

S-400 Series (Partial Data):

ModeDC Output VoltageRated CurrentOutput Current RangeOutput PowerRipple and Noise
S-400-55V60A0-60A300W100mVp-p
S-400-1212V33A0-33A396W150mVp-p
S-400-2424V16.5A0-16.5A396W150mVp-p

5. Setup and Installation

Follow these steps for safe and correct installation:

  1. Mounting: Securely mount the power supply in a well-ventilated area. Ensure adequate clearance around the unit for airflow, especially if it has a cooling fan.
  2. AC Input Connection:
    Connect the AC input wires to the terminal block as follows:
    • Connect the Live (L) wire to the 'L' terminal.
    • Connect the Neutral (N) wire to the 'N' terminal.
    • Connect the Ground wire to the ground symbol terminal (✉).

    The power supply supports a wide AC input range, typically 100-240VAC at 50/60Hz. Refer to the product label for specific input voltage requirements (e.g., 100-120VAC 6.5A or 200-240VAC 3.5A).

  3. DC Output Connection:
    Connect your load to the DC output terminals:
    • Connect the positive (+) wire of your load to the '+V' terminal.
    • Connect the negative (-) wire of your load to the '-V' terminal.
  4. Initial Check: Before powering on, double-check all connections to ensure they are secure and correctly wired.

6. Operation

Once installed, operate the power supply as follows:

  1. Power On: Apply AC power to the unit. The power LED indicator (if present) should light up.
  2. Voltage Adjustment: If your model includes a '+V ADJ' potentiometer, you can fine-tune the output voltage within a specified range (typically ±10% of the nominal output voltage). Use a small screwdriver to carefully turn the potentiometer. Monitor the output voltage with a multimeter to achieve the desired setting.
  3. Cooling Fan Operation: Some models feature a cooling fan. The fan control logic may vary, for example:
    • Fan on when temperature ≥50℃.
    • Fan off when temperature ≤45℃.
    • Cut off output when temperature ≥80℃ (5-7.5V).

    Ensure the fan is not obstructed and can operate freely.

7. Maintenance

To ensure the longevity and optimal performance of your power supply:

  • Cleaning: Periodically clean the exterior of the unit with a soft, dry cloth. Ensure ventilation openings are free from dust and debris. Do not use liquid cleaners.
  • Environmental Conditions: Operate and store the power supply within the specified temperature and humidity ranges:
    • Working Temperature: -10℃ to +60℃ (derating may be required at higher temperatures).
    • Working Humidity: 20% to 90% RH (non-condensing).
    • Storage Temperature: -20℃ to +85℃.
    • Storage Humidity: 10% to 95% RH (non-condensing).
  • Inspection: Regularly inspect all wiring connections for tightness and signs of wear or damage.

8. Troubleshooting

If you encounter issues with your power supply, consider the following:

  • No Output Voltage:
    1. Check AC input power and connections.
    2. Verify the power LED indicator is on.
    3. Ensure no short circuit or overload condition is present on the output.
  • Output Voltage Fluctuations:
    1. Check the stability of the AC input voltage.
    2. Ensure the load is within the rated capacity.
    3. Verify the potentiometer setting is stable.
  • Overload Protection Triggered: The unit may enter hiccup mode or shut down if the load exceeds 105-150% of the rated output power. Reduce the load to allow the unit to recover automatically.
  • Overvoltage Protection Triggered: If the output voltage exceeds 115-135% of the rated voltage, the unit will protect itself. Disconnect power, check the load, and restart.
  • Over Temperature Protection: If the internal temperature exceeds safe limits (e.g., ≥85℃), the unit may shut down. Ensure adequate ventilation and reduce ambient temperature. The fan should turn off when the temperature returns to normal.
  • Fan Noise: Some users have reported that the fan can be noisy. If fan noise is a concern, consider placing the unit in an area where the sound will not be disruptive.

9. User Tips

  • Placement: If your power supply model includes a cooling fan, it might produce some noise. Consider placing the unit in a location where fan noise will not be an issue.
  • Verify Dimensions: Be aware that actual product dimensions and appearance may sometimes differ slightly from promotional images. Always verify the exact dimensions and features upon receipt if precise fitment is critical for your application.

10. Warranty and Support

HLTNC provides a warranty for its products. The standard warranty period is typically 3 years, with some series like RSP offering a 5-year warranty. Please retain your purchase receipt for warranty claims.

For detailed information, specific model inquiries, or technical support, please refer to the official user manual (PDF) available from the seller or contact the manufacturer directly. You may also contact Smunchina@163.com for further assistance.

© 2024 HLTNC. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.