wenzhi WZ-M100

Contents

wenzhi WZ-M100 Human Presence Motion Sensor User Manual

Model: WZ-M100

1. Introduction

The wenzhi WZ-M100 is a smart human presence motion sensor designed for home automation and security. It utilizes mmWave radar technology for accurate detection of human presence, motion, micro-motion, and even breathing, along with luminance and distance detection capabilities. This sensor can be integrated into smart home systems via ZigBee or Wi-Fi, supporting platforms like Tuya Smart Life.

wenzhi WZ-M100 Human Presence Motion Sensor, showing both ceiling mount and wall mount versions with ZigBee and Wi-Fi logos.
Figure 1: wenzhi WZ-M100 Human Presence Motion Sensor (Ceiling and Wall Mount)

2. Specifications

Category Parameter Description (5.8GHz Model) Description (24GHz Model)
Physical Parameters Model Number Wall Mount: WZ-M100-W
Ceiling Mount: WZ-M100-C
Wall Mount: WZ-M100-W-24
Ceiling Mount: WZ-M100-C-24
Product Size Wall Mount: 58*58*11mm (2.28*2.28*0.43 inch)
Ceiling Mount: Ø61*H39mm (Ø2.4*H1.54 inch)
Wall Mount: 58*58*11mm (2.28*2.28*0.43 inch)
Ceiling Mount: Ø61*H39mm (Ø2.4*H1.54 inch)
Product Weight 70g
Sensor Parameters Beam Angle 120x120° (signal energy decays by 3dB at 0°) 100x100° (signal energy decays by 3dB at 0°)
Ceiling Detection Radius Presence: 2.5~3m
Motion: 4~5.5m
Presence: 2~3m
Motion: 4~4.5m
Sensitivity 1-9 (Typical 7) Trigger: 0-9 (Typical 5)
Maintain: 0-9 (Typical 7)
Sense Distance 0-10m, Default 6m 0.3-10m, Default 6m
Ceiling Installation Height Typical height: 2.7-3.5 m
System Parameters Unmanned Delay 5s~1500s, Default: 15s
Illuminance 0~2000 Lux (Approximate brightness of the environment)
Human Confirmation Delay 0~100s, Default: 0.1s
Report Interval Time 1~3600s, Default: 5s (Controls data reporting frequency)
Working Frequency 5.8 GHz 24 GHz
Transmitting Power 3~5 dBm 10 dBm
Networking Method ZigBee3.0 / Wi-Fi (2.4GHz) / BLE
Working Voltage Wall Mount: USB 5V Ceiling Mount: 80-240VAC
Working Temperature -20℃~+70℃
Storage Temperature -20℃~+70℃
Other Parameters Working Humidity 5~90% RH (No Condensation)
Working Altitude 0-3500m
Restricted Usage Scenarios In elevators, metal sealed toilets, and similar all-metal sealed spaces. Scenarios where the plane area of metal decorative materials outside the non-ceiling area exceeds 20%.

3. Setup

3.1. Installation Guidelines

Observe the following principles for optimal sensor performance:

  • General Placement: In hallways, changing rooms, and kitchens, install the sensor as centrally and firmly as possible.
  • Bathrooms/Toilets: Install 0.4-0.6m in front of the toilet/squatting position, away from doors, windows, and exhaust fans.
  • Living/Dining/Conference Rooms: Place 0.5-1m in front of the sofa, directly above the table.
  • Bedrooms/Studies: Position directly above the bed, within 0.6-1.5 meters behind the table.
  • Glass/Gypsum Board Partitions: Mount the sensor as close to a solid wall as possible. If only glass or gypsum board walls are present, install centrally and adjust detection range and sensitivity to prevent detection beyond the intended area.
  • Dense Deployment: The linear spacing between sensors should not be less than 5m.

3.2. Physical Installation

The sensor comes in two main mounting types: wall mount and ceiling mount.

wenzhi Wifi Smart Human Presence Sensor, wall mount version with USB 5V input.
Figure 2: Wall Mount Sensor (USB 5V Input)
  • Wall Mounted Installation:
    1. Recommended installation height: 1.5 to 2 meters above the ground.
    2. Power the device using a 5V 1A USB power supply.
    3. Apply double-sided adhesive to the back of the wall-mounted sensor and firmly attach it to the desired position.
  • Ceiling Mounted Installation:
    1. Prepare a ceiling opening with a diameter of 53-58mm. A 55mm opening is recommended.
    2. Install the sensor into the opening using the two end buckles.
    3. It is recommended to complete the network connection (pairing with the app) before final installation into the ceiling.
ZigBee Smart Human Presence Sensor and ZigBee Hub, illustrating home automation and alarm push functionality with a smartphone app screenshot.
Figure 3: ZigBee Setup with Hub and App Interface

3.3. App Installation and Network Connection

The wenzhi WZ-M100 sensor integrates with the Tuya Smart Life app for smart home control.

  1. App Installation:
    • Search for "Tuya Smart" or "Smart Life" in your device's app store and download it.
    • Alternatively, scan the QR code provided in the original manual (refer to the PDF manual for the QR code) to download the app.
    • After installation, register and log in to your account.
  2. Network Connection (Pairing):
    • Initial Power-On: When the sensor is powered on for the first time or is not yet connected to a network, it will automatically enter network connection mode. The red indicator light will flash quickly.
    • Re-entry into Pairing Mode: If pairing fails or the red light is not flashing quickly, power cycle the device or press and hold the network connection button for more than 5 seconds to re-enter pairing mode.
    • Connecting via App:
      1. Open and log in to the Smart Life/Tuya app.
      2. Tap the "+" symbol in the upper right corner and select "Add Device".
      3. The app will search for nearby devices. Once your sensor is discovered, tap "Add".
      4. Upon successful addition, the sensor's red indicator light will turn off.
    • ZigBee Version: For ZigBee models, ensure you have a compatible ZigBee hub (gateway) and connect the sensor to it through the app.

3.4. ZigBee2mqtt Support

For users integrating with ZigBee2mqtt, ensure your ZigBee2mqtt instance is updated to the latest version. If issues persist, you may need to download and configure the JS file from the official wenzhi GitHub repository:

https://github.com/wzwenzhi/Wenzhi-ZigBee2mqtt

Follow the documentation provided in the link for proper configuration.

4. Operating Instructions

The wenzhi WZ-M100 sensor offers various detection functions and can be configured via the Tuya Smart Life app.

4.1. Detection Functions

The sensor is capable of detecting different types of human activity:

Diagram showing fretting detection, presence detection, motion detection, and distance measurement capabilities.
Figure 4: Various Detection Functions
  • Fretting Detection: Detects subtle, restless movements.
  • Presence Detection: Identifies static human presence (standing still, squatting still, sitting still).
  • Motion Detection: Recognizes larger movements like walking, jogging, or turning.
  • Distance Measurement: Provides an approximate distance of detected objects.
Functional Detection Sensor with More Accuracy, showing scenarios like sleeping, talking, fall alarm, and blinking detection.
Figure 5: Accurate Detection in Various Scenarios

4.2. Setting Detection Distance

The detection distance of the mmWave radar can be adjusted within the app to suit your environment and needs.

mmWave Radar Detection, showing a smartphone app interface to set the detection distance, currently set to 6.00 meters.
Figure 6: Adjusting Detection Distance in the App

The detection distance refers to the maximum linear distance from the sensor to a target that can be detected. It is not the maximum diameter or radius projected onto the ground. The sensor has a distance resolution of approximately 1m. Setting a distance of 3m means detection is normal within ±1m of the 3m position. This setting is primarily used to filter out detections through glass partitions, gypsum boards, or wooden partitions, rather than strictly defining detection zones.

4.3. Illumination Detection Function

The sensor also includes an illumination detection function, allowing it to measure the ambient light level (0-2000 Lux). This data can be used in smart home automations, for example, to control lighting based on room brightness.

Illumination detection function, showing the sensor mounted on a wall in a brightly lit room.
Figure 7: Illumination Detection in Action

5. Maintenance

  • Cleaning: Gently wipe the sensor's surface with a soft, dry cloth. Do not use liquid cleaners or aerosols, as they may damage the device.
  • Placement: Ensure the sensor is not obstructed by furniture, curtains, or other objects that could interfere with its detection range.
  • Power Supply: For wall-mounted USB 5V models, ensure a stable power supply. For ceiling-mounted AC models, ensure proper electrical connection.
  • Environmental Conditions: Avoid placing the sensor in areas with extreme temperatures or humidity, or in direct sunlight, which could affect its performance and lifespan.

6. Troubleshooting

This section addresses common issues and provides solutions for the wenzhi WZ-M100 sensor.

Interference Source Solution
Fans Change the position of the fan or sensor. Ensure the fan is not within the presence detection area.
Air Conditioning Ensure the air swing and louver vibration of the air conditioning unit are outside the sensor's presence detection area.
Rolling Shutters with Aluminum Alloy Lower Rail Set an appropriate detection range to filter out such interference.
Exhaust Fans Avoid exhaust fans or vibrating surfaces within the sensor's detection range. Secure the exhaust fan to prevent ceiling vibration.
Strong 5.8GHz Wi-Fi Signal Interference
  • Install Wi-Fi routers in the front area of the sensor at least 3m away.
  • For routers in other directions, maintain a distance of at least 1.5m between the router and the sensor.
  • When using a top-mounted Access Point (AP), maintain a distance of at least 1.5m between the AP and the sensor.
Air Flow (Wind) Adjust the sensor's sensitivity setting.
Animals Adjust the sensitivity and minimum detection distance settings to minimize false triggers.
Low Frequency Vibration Avoid direct exposure of radar signals to vibrating sources like speakers. Set a relatively low sensitivity to prevent false triggers and use a longer "Human Confirmation Delay" time.
Sensor Not Connecting to Network Ensure the sensor is in pairing mode (red light flashing quickly). Power cycle the device or press and hold the pairing button for 5+ seconds. Check Wi-Fi/ZigBee gateway status.
Inaccurate Detection Review installation guidelines (Section 3.1) for optimal placement. Adjust sensitivity and detection distance settings in the app. Ensure no obstructions are blocking the sensor's field of view.

7. User Tips

  • Compatibility: The sensor is compatible with all devices that support ZigBee or Wi-Fi connectivity through the Tuya Smart Life platform.
  • Connection: It connects via both Wi-Fi and ZigBee, offering flexibility for different smart home setups.
  • App Integration: Leverage the Tuya Smart Life app to customize detection parameters, set up automation routines, and receive alerts.
  • Optimal Placement: For best results, consider the detection range and beam angle when choosing between ceiling and wall mount options, and position the sensor to cover the desired area without interference.

8. Warranty and Support

8.1. Warranty Policy

The wenzhi WZ-M100 Human Presence Motion Sensor comes with a warranty policy as follows:

  • Free Warranty Service: Within one year from the date of receipt, free warranty service is provided for performance failures occurring during normal use.
  • Non-Free Warranty Regulations: The warranty does not cover:
    • Unauthorized repair, collision, accident, negligence, misuse, abuse, modification, incorrect use, or tearing/tampering with anti-counterfeiting labels.
    • Damage caused by force majeure (e.g., natural disasters).
    • Performance failures of products and their accessories caused by human factors (e.g., intentional damage).

8.2. Regulatory Compliance (FCC)

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation.

If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Important:

Changes or modifications not expressly approved by the manufacturer responsible for compliance could void the user's authority to operate the equipment.

8.3. Manufacturer Information

Wenzhou Wenzhi Automation Technology Co., Ltd
Address: B203, No. 228 Wenzhou Avenue, Puzhou Jiedao, Longwan District, Wenzhou City, Zhejiang Province, 325000, China

EU Representative (EC REP): MJCM SARL
Address: 78 avenue des Champs-Elysees Bureau 326
Email: mjcm190928@gmail.com
Tel: +33 767213611

UK Representative (UK REP): EU&MJCM LTD
Address: R.487 5 Brayford Square, London, England, E1 0SG

Certifications: FC CE ROHS

Made in China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.