Ziqqucu AMS1117 Step Down Power Module

Contents

AMS1117 Step-Down Voltage Regulator Module User Manual

Model: AMS1117 Step Down Power Module | Brand: Ziqqucu

1. Introduction

This manual provides detailed instructions for the Ziqqucu AMS1117 Step-Down Voltage Regulator Module. This module is designed to convert a higher DC input voltage to a stable lower DC output voltage, available in 3.3V and 5V versions. It is suitable for various electronic projects requiring a regulated power supply.

Multiple AMS1117 5V Step-Down Modules
Figure 1: Overview of AMS1117 5V Step-Down Modules.
Single AMS1117 3.3V Step-Down Module
Figure 2: Overview of a single AMS1117 3.3V Step-Down Module.

2. Safety Information

  • Ensure all connections are correct before applying power. Incorrect wiring can damage the module or connected devices.
  • Do not exceed the maximum input voltage or output current specifications.
  • Handle the module with care to avoid electrostatic discharge (ESD) damage.
  • Keep the module away from moisture and extreme temperatures.
  • If you are unsure about any step, consult a qualified electronics professional.

3. Specifications

Feature 3.3V Version 5V Version
Input Voltage (VIN) DC 4.5V - 7V (VIN must be at least 1V higher than output) DC 6V - 12V (VIN must be more than 1V higher than output)
Output Voltage (OUT) 3.3V 5.0V (± 0.05V error)
Output Current (Max) 800mA (constant load current can exceed 800mA) 800mA (constant load current can exceed 800mA)
Low Voltage Differential 1.2V (Input only 1.2V higher than output for normal operation) N/A
Module Dimensions (3.3V) 8.6mm x 12.33mm N/A
PCB Board Size (5V) N/A 2.5cm x 1.1cm
Pins 2P single row pins for Input (VIN), Ground (GND), and Output (OUT)
Indicator Red power indicator light
Type Voltage Regulator

Package Contents:

  • Power module x 1 (quantity may vary based on purchase option)

For more detailed specifications, you may refer to the official user manual PDF: AMS1117 Module User Manual (PDF)

4. Setup and Installation

Follow these steps to correctly set up your AMS1117 module:

  1. Identify Pins: Locate the three pins on the module: VIN (Input Voltage), GND (Ground), and OUT (Output Voltage).
    Close-up of AMS1117 module showing VIN, OUT, GND pins
    Figure 3: Pin identification (VIN, OUT, GND).
  2. Connect Input Voltage (VIN): Connect your DC power source's positive terminal to the VIN pin of the module. Ensure the input voltage is within the specified range for your module version (DC 4.5V-7V for 3.3V output, DC 6V-12V for 5V output).
  3. Connect Ground (GND): Connect the ground (negative) terminal of your DC power source to the GND pin of the module. Also, connect the ground of your load device to this GND pin.
  4. Connect Output Voltage (OUT): Connect the positive power input of your load device to the OUT pin of the module.
    Two AMS1117 modules, showing top and bottom views
    Figure 4: Various views of the module for connection reference.
  5. Verify Voltage Differential: For proper operation, the input voltage (VIN) must be at least 1V higher than the desired output voltage (OUT). For the 3.3V version, a minimum 1.2V differential is required.

5. Operating Instructions

Once the module is correctly wired and power is applied:

  • The red power indicator light on the module should illuminate, indicating that the module is receiving power and operating.
  • The module will automatically regulate the input voltage down to the specified output voltage (3.3V or 5V).
  • Ensure the total current drawn by your load does not exceed 800mA to prevent damage to the module.

6. Maintenance

  • Cleaning: Keep the module clean and free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Environment: Operate the module in a dry, well-ventilated environment. Avoid exposure to high humidity, corrosive gases, or extreme temperatures.
  • Inspection: Periodically inspect the module for any signs of physical damage, loose connections, or discoloration which might indicate overheating.

7. Troubleshooting

Problem Possible Cause Solution
No output voltage / Power indicator off No input power, incorrect wiring, or input voltage too low. Check power source, verify VIN and GND connections, ensure input voltage is within specified range and meets minimum differential.
Output voltage is unstable or incorrect Input voltage fluctuations, load current exceeds 800mA, or insufficient input-output voltage differential. Use a stable input power source, reduce load current, ensure input voltage is sufficiently higher than output (at least 1V, or 1.2V for 3.3V version).
Module overheating Load current too high, or poor ventilation. Reduce load current to below 800mA. Ensure adequate airflow around the module.

8. User Tips

  • Always double-check your wiring before applying power to avoid damaging the module or your project.
  • When testing, use a multimeter to verify input and output voltages to ensure correct operation.
  • Consider adding a small heatsink if the module is expected to operate at its maximum current capacity for extended periods, especially in enclosed spaces.
  • For sensitive applications, adding additional input/output capacitors might improve stability, though the module typically includes sufficient onboard capacitance.

9. Frequently Asked Questions (FAQ)

Q: Can I use this module to boost voltage?
A: No, this is a step-down (buck) voltage regulator module, meaning it can only reduce voltage, not increase it.
Q: What is the maximum current output?
A: The module can supply a constant load current of up to 800mA.
Q: Why is the output voltage lower than expected?
A: Ensure your input voltage is sufficiently higher than the desired output voltage (at least 1V, or 1.2V for the 3.3V version). Also, check if your load is drawing more than 800mA, which could cause voltage drop.

10. Warranty and Support

Specific warranty details for this product are not provided in this manual. For any warranty claims, technical support, or further inquiries, please contact the seller or manufacturer directly through your purchase platform.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.