RACBOX Car LED Tail Light Rear High-mounted 3rd Brake Stop Light

Contents

RACBOX Universal Car LED High-Mounted 3rd Brake Stop Light User Manual

Model: Car LED Tail Light Rear High-mounted 3rd Brake Stop Light

1. Introduction

Thank you for purchasing the RACBOX Universal Car LED High-Mounted 3rd Brake Stop Light. This product is designed to enhance your vehicle's safety by providing an additional, highly visible brake signal. Please read this manual carefully before installation and use to ensure proper function and longevity of the product.

RACBOX LED 3rd Brake Light, showing the light unlit and illuminated bright red.

Figure 1: RACBOX LED 3rd Brake Light (unlit and illuminated)

2. Safety Information

  • Always disconnect the vehicle's battery before performing any electrical work.
  • Ensure all wiring connections are secure and properly insulated to prevent short circuits.
  • Do not modify the product. Unauthorized modifications may void the warranty and create safety hazards.
  • Consult a professional automotive technician if you are unsure about any installation steps.

3. Setup and Installation

3.1. Package Contents

  • 1 x RACBOX LED High-Mounted 3rd Brake Stop Light

3.2. Tools Required

  • Wire strippers/cutters
  • Electrical tape or heat shrink tubing
  • Crimping tool (if using crimp connectors)
  • Multimeter (optional, for testing voltage)
  • Drill (if new mounting holes are required)

3.3. Installation Steps

  1. Choose Mounting Location: Select a suitable high-mounted position on the rear of your vehicle, such as on the rear spoiler or above the rear window. Ensure the light will be clearly visible to following drivers and does not obstruct your rear view.
  2. Prepare Mounting Surface: Clean the mounting area thoroughly. If drilling new holes, mark the positions carefully, ensuring they align with the light's mounting points.
  3. Mount the Light: Secure the brake light using appropriate fasteners. Ensure it is firmly attached and stable.
  4. Wiring:
    • Locate your vehicle's existing brake light wiring. You will need to tap into the positive (+) and negative (-) wires of your vehicle's brake light circuit.
    • Connect the Red wire from the RACBOX LED light to the Positive (+) wire of your vehicle's brake light circuit.
    • Connect the Black wire from the RACBOX LED light to the Negative (-) / Ground wire of your vehicle's electrical system.
    Wiring diagram showing red wire for positive and black wire for negative connection.

    Figure 2: 2-Wire Connection Diagram

  5. Secure Connections: Use electrical tape or heat shrink tubing to insulate all connections properly. Ensure no bare wires are exposed to prevent short circuits or corrosion.
  6. Test Functionality: Before fully reassembling any vehicle panels, test the brake light by pressing the brake pedal. Ensure the new LED light illuminates brightly when the brakes are applied and turns off when released.
  7. Final Assembly: Once tested and confirmed working, secure all wiring and reassemble any removed vehicle panels.
Examples of the 3rd brake light installed on the rear of an SUV and a pickup truck.

Figure 3: Installation Examples

4. Operating Instructions

The RACBOX LED High-Mounted 3rd Brake Stop Light operates automatically. It will illuminate when the vehicle's brake pedal is pressed and turn off when the brake pedal is released, in conjunction with your vehicle's existing brake lights.

5. Maintenance

  • Cleaning: Clean the light's lens periodically with a soft cloth and mild soap solution. Avoid abrasive cleaners that could scratch the lens.
  • Inspection: Periodically check the wiring for any signs of wear, corrosion, or damage. Ensure all connections remain secure.
  • Mounting: Verify that the light remains securely mounted to the vehicle. Tighten any loose fasteners if necessary.

6. Troubleshooting

ProblemPossible CauseSolution
Light does not illuminate
  • Incorrect wiring (reversed polarity, loose connection)
  • No power to the circuit
  • Blown fuse in vehicle's brake light circuit
  • Faulty LED unit
  • Check and correct wiring connections (positive/negative).
  • Verify 12V power is reaching the light with a multimeter.
  • Check and replace the vehicle's brake light fuse if necessary.
  • Contact seller for support if LED unit is faulty.
Light flickers or is dim
  • Loose wiring connection
  • Insufficient power supply
  • Inspect and secure all wiring connections.
  • Ensure a stable 12V power supply.
Water inside the light
  • Improper sealing during installation
  • Damage to the light housing
  • Ensure the light is properly sealed to the vehicle surface.
  • If housing is damaged, contact seller for replacement.

7. Specifications

FeatureSpecification
Product TypeCar LED Tail Light Rear High-mounted 3rd Brake Stop Light
Shell ColorRed
Light ColorRed
MaterialPlastic
Voltage12V
Lighting TypeLED
LED Quantity18LED (for 340mm model) / 24LED (for 390mm model)
Dimensions (18LED Model)Approx. 340mm (Length) x 42mm (Height) x 8mm (Thickness)
Dimensions (24LED Model)Approx. 390mm (Length) x 55mm (Height)
Waterproof RatingIP67
Product specification diagram showing dimensions for 340mm and 390mm models.

Figure 4: Product Dimensions (340mm and 390mm models)

Product specification diagram showing 300mm mounting hole distance for 340mm model and 8mm thickness.

Figure 5: Product Dimensions (340mm model with mounting hole distance)

Image highlighting the IP67 waterproof design, showing resistance to sand, dust, snow, and water.

Figure 6: IP67 Waterproof Design

8. User Tips

  • Verify Compatibility: Before purchasing or installing, carefully measure the available space and the distance between any existing mounting holes on your vehicle's spoiler or mounting surface. Compare these measurements with the product dimensions provided in Section 7 to ensure a proper fit.
  • Pre-fit Check: Always perform a dry fit of the light in your desired location before making any permanent modifications or wiring connections.
  • PDF Manual: A detailed user manual in PDF format may be available from the seller. Refer to it for additional information or specific vehicle compatibility details.

9. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your retailer or the platform where you purchased this product. If you encounter any issues or require technical assistance, please contact the seller directly with your order details.

© 2024 RACBOX. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.