diymore DCE003

Contents

DC-DC Step Down Power Supply Module Instruction Manual

Model: DCE003

Brand: diymore

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the diymore DCE003 DC-DC Step Down Power Supply Module. This module is designed to convert a high DC input voltage (6V-100V) to a lower, fixed DC output voltage (5V, 9V, 12V, or 24V). It features overheat and overload shutdown protection, making it suitable for various applications including smart home devices, industrial IoT, and vehicle power supplies.

For a comprehensive guide, you may also refer to the User Manual (PDF).

2. Safety Information

Please read and understand all safety precautions before installing or operating this module. Failure to do so may result in electric shock, fire, or damage to the module or connected devices.

  • Ensure the input voltage does not exceed 100V DC.
  • Always ensure the input voltage is higher than the desired output voltage.
  • Do not exceed the maximum output current of 2A for long-term operation (3A peak).
  • Disconnect power before making any connections or adjustments.
  • This module is unisolated; take appropriate precautions when integrating into systems.
  • Operate within the specified temperature and humidity ranges.

3. Product Features

  • Fixed output voltages: 5V, 9V, 12V, 24V (selectable via solder pads).
  • Wide input voltage range: 6V-100V DC.
  • Overheat and overload shutdown protection.
  • Compact size: 25.5mm x 16.5mm x 7mm (L*W*H).
  • High conversion efficiency: Up to 96%.
  • Low output ripple: <30mA.
  • Output accuracy: ±0.1V.
  • Built-in shutdown function (EN pin).
  • Motherboard half-hole design for SMD integration.
DC-DC Step Down Power Supply Module
Overview of the DC-DC Step Down Power Supply Module.

4. Specifications

Parameter Value
Input Voltage7V-100V (Input must be greater than output)
Output Voltage5V/9V/12V/24V (Fixed)
Output Current3A (maximum peak), 2A (long-term current)
Conversion Efficiency96% (maximum)
Output Ripple<30mA
Output Accuracy±0.1V
No-load Current1mA
Operating Temperature-40°C to +125°C
Working Humidity20%-90%
Dimensions (L*W*H)25.5mm x 16.5mm x 7mm
PCB Layers2 layers
Shutdown FunctionYes
Heat Dissipation ModeNatural heat dissipation
Installation ModeWelding wire, patch
IsolationUnisolated
Production TechnologyReflow welding
Service Life35000 hours without fault (output current does not exceed rating)
Operating Frequency1MHz
Product dimensions diagram
Detailed dimensions of the module (25.5mm x 16.5mm x 7mm).

5. Installation and Setup

5.1. Pinout Description

Module pinout and wiring diagram
Pinout and basic wiring connections for the DC-DC module.
  • IN-: Negative input terminal.
  • IN+: Positive input terminal.
  • OUT-: Negative output terminal.
  • OUT+: Positive output terminal.
  • EN (On/Off): Enable pin. Applying a positive input level to this pin enables the output. Disconnecting this pin (or pulling it low) will close the output. By default, the module powers on with the output enabled if this pin is connected to the input positive terminal.

5.2. Output Voltage Selection

The module provides fixed output voltages. The desired output voltage (5V, 9V, 12V, or 24V) is selected by soldering specific pads on the bottom of the module. Refer to the diagram below for the solder pad configuration.

Bottom view of module showing output voltage selection pads
Bottom view of the module with solder pads for selecting fixed output voltages (5V, 9V, 12V, 24V).

To select an output voltage, bridge the corresponding solder pads. For example, to select 12V output, bridge the pads labeled '12'.

5.3. Wiring Instructions

  1. Identify the IN+ and IN- terminals for your input power source.
  2. Identify the OUT+ and OUT- terminals for your load.
  3. Ensure the input voltage is within the 6V-100V range and is greater than your selected output voltage.
  4. Connect the positive terminal of your input power source to IN+.
  5. Connect the negative terminal of your input power source to IN-.
  6. Connect the positive terminal of your load to OUT+.
  7. Connect the negative terminal of your load to OUT-.
  8. If using the shutdown function, connect the EN pin as required. For continuous operation, connect EN to IN+.
  9. Double-check all connections before applying power.

6. Operating Instructions

Once the module is correctly wired and the output voltage is selected, apply power to the input terminals. The module will automatically regulate the voltage to the chosen fixed output. The shutdown function can be utilized via the EN pin to control the output without disconnecting the main input power.

The module is designed for natural heat dissipation. Ensure adequate airflow around the module, especially when operating at higher currents or ambient temperatures, to prevent overheating.

7. Maintenance

This module requires minimal maintenance. Keep the module clean and free from dust and debris. Avoid exposing it to excessive moisture or corrosive environments. Regularly inspect connections for any signs of wear or damage. Do not attempt to repair the module if it is damaged; contact support or replace the unit.

8. Troubleshooting

  • No Output Voltage / Output Voltage same as Input:
    • Verify that the input voltage is correctly connected to IN+ and IN-.
    • Ensure the input voltage is sufficiently higher than the selected output voltage (e.g., for 5V output, input should be at least 7V).
    • Check the output voltage selection solder pads to ensure the correct voltage is selected and the connection is solid.
    • Inspect the EN pin connection. If it's disconnected or pulled low, the output will be off. Connect it to IN+ for continuous operation.
    • Confirm the module is not overloaded. Reduce the load current to see if the output stabilizes.
    • If the issue persists, the module might be faulty.
  • Module Overheating:
    • Ensure adequate ventilation around the module.
    • Verify that the output current does not exceed the specified limits (2A continuous, 3A peak).
    • Check if the input voltage is excessively high for the desired output, leading to higher power dissipation.
  • Unstable Output Voltage:
    • Check for loose connections at input or output terminals.
    • Ensure the input power supply is stable and within the specified range.
    • Verify that the load is not drawing current intermittently or exceeding the module's capacity.

9. User Tips

  • Many users report accurate and stable voltage output, making it reliable for various projects.
  • The compact size is frequently praised for fitting into tight spaces.
  • Consider using a multimeter to verify the output voltage after setup, especially when selecting fixed voltage via solder pads.

10. Warranty and Support

For warranty information and technical support, please contact the seller or manufacturer directly. Keep your purchase records for any warranty claims.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.