Voktta DC-DC Buck Module

Contents

LM2596 DC to DC Buck Converter User Manual

High Efficiency Voltage Regulator Module

1. Introduction

This manual provides instructions for the Voktta LM2596 DC to DC Buck Converter module. This high-efficiency voltage regulator is designed to step down a higher input voltage to a lower, stable output voltage. It is suitable for various DIY power supply projects, industrial control systems, low ripple and low noise power supplies, and automotive electronic power supplies. The module is available in both fixed voltage and adjustable output versions, offering flexibility for different applications.

2. Safety Information

  • Always ensure proper polarity when connecting the module to a power source. Incorrect connections can damage the module and connected devices.
  • Do not exceed the maximum input voltage of 60V or the maximum output current of 3A.
  • Operate the module within its specified junction temperature range (-40℃ to +125℃).
  • Handle electronic components with care to avoid electrostatic discharge.
  • If you are unsure about any wiring or configuration, consult a qualified electronics professional.

3. Product Overview

The LM2596 DC to DC Buck Converter is a high-quality step-down module featuring efficient synchronous voltage reduction and low ripple output. It incorporates high-frequency, low internal resistance, and long-life capacitors for stable performance.

3.1 Features

  • Efficient synchronous voltage reduction with up to 3A current output and low ripple.
  • Available in multiple styles: fixed voltage versions (3.3V, 5V, 12V, 24V) and adjustable potentiometer versions (2-34V or 3-32V).
  • Automatically switched bypass linear power supply for improved high voltage and light load efficiency.
  • Utilizes high-frequency, low internal resistance, and long-life capacitors.
  • Wide input voltage range (2V-60V), stable and consistent output, and fast dynamic response.
  • Supports large load capacitor startup and is applicable for flushing supercapacitors.
  • Multiple protection functions: Undervoltage Lockout (UVLO), Overcurrent Protection (OCP), Short Circuit Protection (SCP), Overtemperature Protection (OTP), Overvoltage Protection (OVP).
  • Wide junction temperature range: -40℃ to +125℃.
  • Supports variable frequency, with a default working frequency of 400kHz, and 1M after short circuiting.

3.2 Components

The module consists of input and output terminals, an inductor, capacitors, and a voltage regulation circuit. Adjustable versions include a potentiometer for output voltage adjustment.

Top view of the long LM2596 buck converter module showing input and output terminals, inductor, and capacitors.
Figure 1: Top view of the long LM2596 buck converter module.
Top view of the square LM2596 buck converter module showing input and output terminals, inductor, and capacitors.
Figure 2: Top view of the square LM2596 buck converter module.

4. Specifications

Table 1: Product Specifications
Parameter Value
Model Number DC-DC Buck Module (LM2596)
Input Voltage Range 2V - 60V (Note: If current is high, input voltage should be >1V higher than output voltage)
Output Voltage Range (Fixed Versions) 3.3V, 5V, 12V, 24V
Output Voltage Range (Adjustable Versions) 2V - 34V (potentiometer board), 3V - 32V (adjustable potentiometer)
Output Current Max 3A
Output Power 1 - 50W
Output Type SINGLE
Static Current Ultra low 20uA
Junction Temperature Range -40℃ to +125℃
Working Frequency Default 400kHz, 1M after short circuiting
Dimensions (Long Model) 43.00mm x 20.00mm x 13.5mm (with potentiometer)
Dimensions (Square Model) 26.00mm x 20.50mm x 9.2mm (chip inductance)
Weight 19g
Certification CE
Diagram showing dimensions of both long and square LM2596 buck converter modules, including thickness and component sizes.
Figure 3: Product dimensions for both long and square module types.

5. Setup Instructions

Before connecting the module, ensure your power source and load are compatible with the module's specifications.

5.1 Pin Connections

Refer to the pin description table and diagram below for correct wiring.

Table detailing the pin names, direction (input/output), and description for the LM2596 buck converter module.
Figure 4: Pin Description Table.
Table 2: Pin Description
Pin Name Direction Description
IN+ Input Power supply input positive pole. Ensure OUT+ < IN+ < 60V.
IN-/GND Input Input ground/negative pole. Directly connected to output ground.
OUT+ Output Positive pole of output power supply.
OUT-/GND Output Output ground/negative pole. Directly connected to input ground.

5.2 Voltage Configuration

Adjustable Versions (e.g., 2-34V, 3-32V)

Connect the input power. Use a small screwdriver to gently turn the onboard potentiometer clockwise to increase the output voltage, or counter-clockwise to decrease it. Monitor the output voltage with a multimeter during adjustment.

Long LM2596 module with 3-32V adjustable output, showing the potentiometer.
Figure 5: Adjustable 3-32V output module.
Long LM2596 module with 2-34V adjustable output, showing the potentiometer.
Figure 6: Adjustable 2-34V output module.

Fixed Voltage Versions (e.g., 3.3V, 5V, 12V, 24V)

For fixed voltage versions, the desired output voltage (3.3V, 5V, 12V, or 24V) is set by shorting specific contacts on the module. Refer to the product diagram (Figure 3, left side) for the "green mark 1234" which indicates the shorting points for different voltages. Ensure the correct contacts are shorted for your desired output.

Long LM2596 module with fixed 3.3V output.
Figure 7: Fixed 3.3V output module.
Long LM2596 module with fixed 5V output.
Figure 8: Fixed 5V output module.
Long LM2596 module with fixed 12V output.
Figure 9: Fixed 12V output module.
Long LM2596 module with fixed 24V output.
Figure 10: Fixed 24V output module.
Square LM2596 module with fixed 3.3/5/12/24V output options.
Figure 11: Square module with fixed voltage options.

6. Operating Instructions

  1. Connect Input Power: Apply a DC voltage within the specified input range (2V-60V) to the IN+ and IN-/GND terminals.
  2. Connect Load: Connect your load to the OUT+ and OUT-/GND terminals.
  3. Verify Output: Before connecting sensitive devices, always verify the output voltage with a multimeter to ensure it matches your requirements.
  4. Current Limit: Ensure the total current drawn by your load does not exceed 3A. Exceeding this limit can damage the module.
  5. Heat Dissipation: For continuous operation at higher currents or larger voltage differences, ensure adequate heat dissipation.

7. Maintenance

  • Keep the module clean and free from dust and debris.
  • Avoid exposing the module to moisture or corrosive environments.
  • Regularly check connections for tightness and signs of wear.
  • Store the module in a dry, cool place when not in use.

8. Troubleshooting

8.1 No Output Voltage

  • Check input power supply: Ensure it is connected correctly and providing voltage within the specified range.
  • Check wiring: Verify all connections (input, output, ground) are secure and correctly polarized.
  • Check for short circuits: Inspect the output for any accidental short circuits.
  • For fixed voltage versions, ensure the correct shorting contacts are made.

8.2 Incorrect Output Voltage

  • For adjustable versions, re-adjust the potentiometer while monitoring with a multimeter.
  • For fixed voltage versions, verify the correct shorting contacts are made for the desired voltage.
  • Ensure the input voltage is sufficiently higher than the desired output voltage (at least 1V difference, especially at higher currents).

8.3 Module Overheating

  • Reduce the load current.
  • Ensure adequate ventilation or add a heatsink if operating at high power.
  • Verify the input/output voltage difference is not excessively large, leading to higher power dissipation.

8.4 Intermittent Output

  • Check for loose connections.
  • Inspect for damaged components or cold solder joints.

9. User Tips

  • Measure Before Connecting: Always use a multimeter to measure the output voltage before connecting any sensitive electronic components to prevent damage.
  • Heat Management: If you plan to draw close to the maximum 3A current, especially with a large voltage step-down, consider adding a small heatsink to the main IC for optimal performance and longevity.
  • Potentiometer Sensitivity: The adjustment potentiometer can be sensitive. Make small, gradual turns and re-measure the output voltage frequently.

10. Warranty and Support

For detailed technical specifications, wiring diagrams, or further assistance, please refer to the official user manual PDF available at: LM2596 Buck Converter User Manual (PDF).

Contact the seller or manufacturer for warranty claims or product support.

© 2023 Voktta. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.