taslauk 2025 LED Strip

Contents

User Manual: 5m High Density 2025 SMD 420 LEDs/m LED Strip Light

Model: 2025 LED Strip | Brand: taslauk

Introduction

This manual provides detailed instructions for the safe and efficient use of your taslauk 5m High Density 2025 SMD LED Strip Light. Please read this manual thoroughly before installation and operation, and retain it for future reference.

1. Product Specifications

ItemDetails
TypeCOB/LED Strip Light
Model Number2025 LED Strip
LED Chip ModelSMD2025
LEDs Number/Meter420 pcs/m
Working Input VoltageDC 24V
Power SourceDC
Wattage20W/m
Luminous Flux1600 lm/m
Emitted Colour OptionsWhite (6000K), Neutral White (4000K), Warm White (3000K)
CRI85+
Length5 meters (L500cm)
PCB Width10mm
Size (approx.)L500cm x W1cm x T0.2cm
Beam Angle140 degrees
Working Temperature-20°C to 60°C (No continuous use beyond this range)
Average Life50,000 hours
Waterproof GradeIP20 (Not waterproof)
CertificationsCE DoC, EMC Testing Report, RoHS Testing Report, UL
Batteries IncludedNo
High-concerned chemicalNone
Intended UseAdvertising lamp backlight, light box, living room decoration

Note: The product is sold in 5-meter lengths.

2. Setup Instructions

2.1 Correct Usage Method

  1. Inspection: Before use, carefully check the product packaging and the LED strip light for any signs of damage. Do not use the strip if the strip itself, wires, or connectors appear damaged.
  2. Power Supply Compatibility: Ensure that the input voltage of your power supply (not included) matches the rated voltage of the LED strip light, which is DC 24V. Using an incompatible power supply can lead to burnout and damage.
  3. Cutting the Strip: If you need a shorter length, cut the strip only at the designated positions. These positions are usually marked with a scissors icon or a clear cut line. Cutting elsewhere may damage the circuit and prevent the remaining part from functioning.
    Close-up of LED strip showing cut marks and 24V markings
    Figure 1: Close-up view of the LED strip, highlighting the 10mm width, 1.428mm segment length, 2025 LED type, 420 LEDs/m density, and +24V connection points. Note the designated cut marks.
  4. Connecting to Power: Connect the LED strip to the power supply correctly by aligning the positive (+) and negative (-) poles. Reverse connection will prevent the strip from lighting up and may cause damage to the product.
  5. RGB Strip Lights (if applicable): For RGB strip lights (this model is single color, but for general guidance), connect the control module (if included) according to its wiring diagram before connecting to the power supply. Test the color change function to ensure proper operation.
  6. Installation Location: Install the strip light in a dry, well-ventilated location. For IP20 rated strips, this means strictly indoor dry locations. Keep it away from flammable materials (e.g., curtains, paper) and high-temperature sources (e.g., stoves, heaters).

3. Operating Instructions

Once properly installed and connected to a compatible DC 24V power supply, the LED strip light will illuminate. The light output will correspond to the selected color temperature (Warm White 3000K, Neutral White 4000K, or White 6000K).

LED strips illuminated in White 6000K, Neutral white 4000K, and Warm white 3000K
Figure 2: Illustration of the available color temperatures: White (6000K), Neutral White (4000K), and Warm White (3000K).

Dimmability

These LED strips are generally dimmable. To achieve dimming functionality, you will need a compatible DC 24V dimmable power supply and/or an LED dimmer switch (not included). Ensure that any dimmer used is designed for 24V LED strip lights and matches the wattage requirements.

4. Maintenance

Cleaning

To clean the LED strip, ensure the power is disconnected. Gently wipe the surface with a soft, dry cloth. Do not use abrasive cleaners, solvents, or excessive moisture, as this can damage the LEDs or the strip's components.

Storage Guidelines

When not in use for extended periods, store the product in a cool, dry place away from direct sunlight and extreme temperatures. This helps maintain its performance and extends its lifespan.

5. Troubleshooting

  • Strip does not light up:
    • Check if the power supply is correctly connected and receiving power.
    • Verify that the positive (+) and negative (-) poles of the LED strip are correctly aligned with the power supply. Reverse connection will prevent illumination.
    • Ensure the power supply voltage matches the strip's requirement (DC 24V).
    • Inspect the strip for any visible damage or improper cuts.
  • Strip is overheating or emitting unusual odor:
    • Immediately disconnect the power supply.
    • Check if the strip is installed in a well-ventilated area and not covered by any materials that block heat dissipation.
    • Ensure the maximum continuous use time of 8 hours is not exceeded.
    • Contact customer support for inspection and repair; do not attempt to disassemble the product yourself.
  • Inconsistent lighting or flickering:
    • Check all connections for looseness.
    • Ensure the power supply is adequate for the total length of the strip.

6. Safety Information & Usage Restrictions

Warning

  • Risk of Electric Shock: Do not touch the connectors or wires with wet hands. Always disconnect the power supply before installing, maintaining, or replacing the product.
  • Risk of Fire: Do not install the strip light near flammable materials (e.g., fabric, wood, plastic) or cover it with any objects that block heat dissipation. Overheating may cause fire or product damage.
  • Unauthorized Modification: Do not modify the product, power cord, or connectors without professional guidance. Any modification must be performed by a qualified electrician. We are not liable for any damage, injury, or loss caused by unauthorized modification, improper use, or installation.
  • Children and Pets: Keep this product out of reach of children and pets to avoid accidental ingestion, electric shock, or burns.
  • Malfunction: If the product malfunctions (e.g., overheating, unusual odor), disconnect the power supply immediately and stop using it. Contact a professional for inspection or repair; do not disassemble the product yourself.
  • Intended Use: This product is not intended for use in medical, industrial, or high-precision equipment applications where equipment failure could cause serious consequences.

Usage Restrictions

  • Indoor Use Only: IP20 strip lights are strictly for indoor dry locations. Do not use in damp or outdoor environments.
  • Continuous Use: Do not exceed a maximum continuous use time of 8 hours. Turn off the strip periodically to allow it to cool down and avoid overheating.
  • Heat Dissipation: Do not wrap the strip light tightly around objects or install it in a sealed space without adequate heat dissipation. This can cause overheating and shorten the service life.
  • Power Cord: The power cord is for dry location use only; do not expose it to water or damp environments.
  • Purpose of Use: Do not use the product for purposes other than lighting (e.g., heating, decoration of high-temperature equipment).

7. User Tips

  • For optimal brightness and longevity, ensure your 24V power supply is robust enough for the entire 5-meter strip.
  • When cutting the strip, always double-check the designated cut marks to avoid damaging the circuit.
  • If planning to dim the lights, invest in a high-quality 24V dimmable power supply and a compatible LED dimmer for best results.

8. Warranty and Support

Warranty Terms

The product warranty is valid only for items used and installed in accordance with the instructions provided in this manual. The warranty is void for damage caused by improper use, unauthorized modification, or natural disasters.

Customer Support

For further assistance or technical support, please contact our customer service team. Refer to your purchase documentation for contact details.

A digital version of this manual is available for download: User Manual (PDF)

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.