Introduction
Thank you for purchasing the noqiz M22 SN Smart Lock. This manual provides detailed instructions for the installation, programming, and operation of your new keypad digital deadbolt. Please read this manual thoroughly before operating your device to ensure proper function and safety. All illustrations are for reference only; the actual product may vary due to product upgrades.
Important Safety Information
- Do not use an electric screwdriver during installation to avoid damaging the lock components.
- Do not load batteries until the lock is completely installed.
- Do not use rechargeable batteries or non-alkaline batteries.
- Keep your Master Code confidential.
- Ensure the door is unlocked and open when installing batteries and performing the door handing process.
- If the keypad and mounting plate are deflected, adjust the mounting plate screws.
- The key must be pulled out when installing.
Product Overview
The noqiz M22 SN Smart Lock is a keyless entry deadbolt featuring a touchscreen keypad, multiple unlock methods, and robust security features. It is designed for easy installation and provides convenience and enhanced security for your home.
Parts List
| Item | Description | Quantity | Image |
|---|---|---|---|
| A | Latch | 1 | ![]() |
| B | Exterior Assembly | 1 | ![]() |
| C | Interior Assembly | 1 | ![]() |
| D | Mounting Plate | 1 | ![]() |
| E | Strike Plate | 1 | ![]() |
| F | Battery Cover | 1 | ![]() |
| G | 3/4" (19mm) Strike/Latch Screws | 4 | |
| H | 1-5/16" (33mm) Mounting Plate Screws | 2 | |
| I | 3/4" (19mm) Interior Assembly Screws | 2 | |
| J | Buckle box | 1 | |
| K | Backup key | 2 | |
| IC Card | 2 |
If any parts are missing or damaged, please contact customer support.
Installation Instructions
For a visual guide, you can scan the QR code on page 4 of the manual or refer to the official product video:
Video: Official product installation and programming guide.
Step 1: Prepare the door and check dimensions
- Measure to confirm that the hole in the door is 2-1/8" (54mm).
- Measure to confirm that the hole in the door edge is 1" (25mm).
- Measure to confirm that the backset is either 2-3/8" or 2-3/4" (60 or 70mm).
- Measure to confirm that the door is 1-3/8" to 2" (35mm or 50mm) thick.
- Make sure the hole in the door frame is drilled a minimum of 1" (25mm) deep.
Diagram illustrating door dimensions for installation.
Step 1-1: Instructions for drilling a new door (if applicable)
- Cut out the template provided in the manual (page 7).
- Fold the template and place it on the door 36" (915mm) from the ground as marked.
- Mark the center hole on the door edge through the template for a 1" (25mm) latch bolt.
- Mark the center hole on the door face through the template for 2-3/8" (60mm) or 2-3/4" (70mm) backset.
Diagram of the installation template for marking drill points.
Step 3: Drill and Chisel Door
- Drill a 2-1/8" (54mm) hole through the door panel as marked for the lock set.
- Drill a 1" (25mm) hole in the center of the door edge for the Deadbolt Latch Assembly.
- Insert the Deadbolt Latch Assembly into the hole, keeping it parallel to the face of the door. Mark the outline and remove the latch.
- Chisel 5/32" (4mm) deep or until the latch face is flush with the door edge.
Diagram showing the process of drilling and chiseling the door for the latch mechanism.
Step 4: Mark and Drill Door Jamb
- Mark the center hole on the edge of the jamb even with the center of the Latch Bolt on the door edge.
- Drill a 1" (25mm) hole 1-3/16" (30mm) deep in the door jamb on the center mark.
- Outline the outside edges of the Strike Plate.
- Chisel 5/32" (4mm) deep for the Strike Plate or until it is flush with the door surface.
- Install the Strike Plate using two 3/4" (19mm) screws provided.
Diagram illustrating how to mark and drill the door jamb for the strike plate.
Step 2: Install the Latch and Strike
- Determine backset and adjust the latch: Hold the latch in front of the door hole. If the slotted hole is centered, no adjustment is required. If not, twist the latch to adjust the bolt length (ensure the latch bolt is retracted).
- Install the latch into the door edge.
- Use a screwdriver to test if the deadbolt works smoothly.
- Install the strike on the door frame. Ensure the hole in the door frame is a minimum of 1" (25mm) deep.
Diagram showing the installation of the latch and strike plate.
Step 3: Install Exterior Assembly
Route the cable through the door below the bolt and push the keypad onto the door. The key must be pulled out when installing.
Diagram showing cable routing and exterior assembly installation.
Step 4: Install Interior Assembly
- Take off the mounting plate (D).
- Route the cable through the bottom of the mounting plate.
- Tighten the mounting plate screws. Note: Support the exterior assembly during mounting plate installation.
- Ensure a tight cable connection. The smooth side of the plug should be at the bottom.
- Tighten the interior assembly screws.
- Insert the key and test the latch. If the latch does not extend or retract smoothly, adjust the mounting plate screws.
Diagram illustrating the installation of the interior assembly and cable connection.
Step 5: Install the batteries and perform the door handing process
- While the door is OPEN and UNLOCKED, load 4 AA batteries into the battery compartment. Do not use rechargeable or non-alkaline batteries.
- Perform the door handing process: Press the SET button, the latch bolt extends by itself.
- Enter the preset programming code: 123456, then press the lock icon. The latch bolt retracts by itself.
Diagram showing battery installation and the door handing process.
Programming Instructions
The default Master Code is 123456. It is required that you change it to your own before programming any other features.
For a visual guide on programming, refer to the official product video:
Video: Official product installation and programming guide.
Definitions
- Master Code: Required for programming and feature settings. Default is 123456.
- Auto Lock: Automatically locks the deadbolt 10 seconds after unlocking. Customizable delay between 5-30 seconds.
- Key Unlock: Always available even if batteries are dead or User Codes are forgotten.
- Low Battery Indicator: Red light flashing after pressing any key indicates low battery. Replace with 4 new AA alkaline batteries.
- Wrong Entry Limit: After 5 incorrect user codes within one minute, the lock shuts down for 90 seconds.
- Silent Mode: Mutes keypad beep sounds, but low battery and system alerts will still sound.
Code Format
- Master Code: 6 digits.
- User Code: 6-9 digits. Up to 50 User Codes can be stored.
- User ID: 2 digits (01 to 50).
Quick Set Up
Press the SET button (inside the battery compartment) to enter programming mode.
- Change Master Code:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 4 ↓ Lock Icon ↓ New Master Code ↓ Lock Icon ↓ Confirm New Master Code ↓ Lock Icon - Add User Code:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 1 ↓ Lock Icon ↓ User ID (01-50 digits) ↓ Lock Icon ↓ New User Code ↓ Lock Icon ↓ Confirm New User Code ↓ Lock Icon - Delete Single User Code:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 2 ↓ Lock Icon ↓ Unwanted User ID (01-50 digits) ↓ Lock Icon ↓ Unwanted User ID (01-50 digits) ↓ Lock Icon - Delete All User Codes:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 3 ↓ Lock Icon ↓ Master Code ↓ Lock Icon - Set Auto-lock (5-30 seconds):
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 5 ↓ Lock Icon ↓ Auto-lock Time (5-30 seconds) ↓ Lock Icon - Cancel Auto-lock:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 5 ↓ Lock Icon ↓ Keyboard 00 ↓ Lock Icon - Sound On/Off:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 6 ↓ Lock Icon ↓ Keyboard 1 (Off) or 2 (On) ↓ Lock Icon - Add IC Card:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 7 ↓ Lock Icon ↓ Put IC Card ↓ Lock Icon - Delete All IC Cards:
SET ↓ Master Code ↓ Lock Icon ↓ Keyboard 8 ↓ Lock Icon ↓ Master Code ↓ Lock Icon
Operating Instructions
Unlock the door from outside
- Enter Master Code + Lock Icon
- Enter User Code + Lock Icon
- Use IC Card
Unlock the door from inside
- Rotate the thumb turn to the horizontal position.
Lock the door from outside
- Auto Lock Mode: The bolt will extend out automatically 10 seconds after unlocking.
- Manual Mode: Press the Lock Icon.
Lock the door from inside
- Auto Lock Mode: The device will be locked automatically.
- Manual Mode: Rotate the thumb turn to the vertical position.
Maintenance
Battery Replacement
When the low battery indicator (red light flashing after pressing any key) appears, replace all 4 AA alkaline batteries immediately. Do not mix old and new batteries, or different types of batteries.
Factory Default Settings (Reset)
Resetting the lock will delete all User Codes. The Master Code will revert to 123456.
- Keep the door open and unlocked.
- Open the battery cover.
- Keep pressing the SET button for more than 5 seconds until the lock gives 5 short beeps and the light flashes blue 5 times. Then, the beep sounds for 1 second and the green light flashes once.
Diagram illustrating the factory reset process.
Troubleshooting
System Alerts
| Alert | Possible Cause | Solution |
|---|---|---|
| Light flashes red 3 times with 3 beeps. | Door jammed while attempting to lock. | Manually re-lock door. If needed, re-position strike. |
| Unsuccessful programming. | Re-start programming procedure. | |
| Incorrect User Code entered. | Re-enter User Code. | |
| Incorrect IC Card entered. | Re-authorize IC Card. | |
| Light flashes red 3 times with 3 beeps. | 5 incorrect User Codes entered within one minute. | Re-enter User Code 90 seconds after keypad lock out. |
| Red light when pressing any button. | Low battery. | Replace batteries. |
| Red light when pressing any button; cannot unlock/lock. | Super low battery. | Replace batteries. |
| Green light and beeps for 1s after pressing unlock/lock button. The lock gives no response. | Poor quality battery. | Replace batteries. |
| The keypad and light indicator give no response. | Battery run out. | Replace batteries. |
| Bad cable connection. | Re-connect the cable. |
Common Issues & Solutions
- Latch not extending/motor rotating during reset: Improper installation. Ensure latch and strike are aligned. Slightly loosen mounting screws if over-tightened. Open door and reset lock.
- Latch not extending/motor not rotating during reset: Deadbolt latch should be retracted (unlocked) throughout installation. Open door and reset lock.
- Latch goes in and out a few times when locking/unlocking: Latch and strike are misaligned. Ensure bolt hole in door frame is at least 1" (25mm) deep. Check if door closes properly and deadbolt goes directly into the hole.
- Lock only works with backup key / key cannot be pulled out when unlocked: Re-install the entire lock. Ensure lock is in unlocked status during installation and the turn knob is horizontal. Do not leave the backup key in the lock.
- 3 short and fast beeps during programming: Indicates time-out or wrong entry. Complete each setting step within 5 seconds.
- Forgot Master Code: Reset the lock to factory default settings. The Master Code will revert to 123456, and all previous user codes will be erased.
Specifications
| Feature | Detail |
|---|---|
| Brand Name | noqiz |
| Model Number | M22 SN |
| Power Supply | DRY BATTERY (4x AA) |
| Handle Direction | Direction Reversible |
| Protection Level | IP66 |
| Fit Door Thickness | 35-50 mm (1-3/8" to 2") |
| Included Components | Deadbolt Strike Plate X 1, Mounting Plate X 1, Touch Keypad Assembly X 1 (and other parts as listed in the Parts List) |
| Finish Type | Other |
| Ways To Unlock | Mechanical Keys, Password, IC Card |
| Origin | Mainland China |
| Certification | FCC |
| High-concerned Chemical | None |
| Max User Codes | 50 |
User Tips
- Read Instructions Carefully: Take your time to read and understand the setup instructions. This will make the installation and programming process much easier.
- Careful Installation: While installation is generally easy, be careful when screwing parts to avoid damage.
- Check Master Keys: Upon receiving your lock, verify that the master keys function correctly. If they don't, contact customer service for assistance.
- Weather Resistance: The lock has an IP66 protection level, indicating good resistance to dust and water jets. It should be suitable for outdoor use in various weather conditions, but extreme cold (e.g., -35°C) might affect battery performance.
- No App/Wi-Fi Integration: This model does not appear to support app control, Wi-Fi connectivity, or integration with smart home systems like Alexa. It operates as a standalone keypad deadbolt.
- IC Card Functionality: The IC card provides an additional method for unlocking the door. If your model includes IC cards, ensure they are programmed as per the instructions.
Warranty & Support
The warranty period for this product is 12 months from the date of purchase. Product specifications are subject to change without notice. The production and sale of this product may be discontinued if electronic parts become unavailable.
If you suspect a malfunction, please provide the following information when contacting support:
- Order number and product model number
- Failure status (explain in as much detail as possible)
For any questions or inquiries regarding malfunctions, please contact us. The manufacturer will not be held liable for incidental or consequential losses or damages due to acts of God.
A PDF version of this user manual is available for download. You can find the link on the product page under 'Item guides & documents'.


