COOSPO BK467

Contents

COOSPO BK467 Cadence and Speed Sensor User Manual

Model: BK467

1. Product Introduction

The COOSPO BK467 is a versatile sensor designed to measure either speed or cadence in real-time. It transmits this data to compatible cycling apps or bike computers via Bluetooth 4.0 and ANT+ protocols. This manual provides detailed instructions to help you effectively use and maintain your BK467 sensor.

2. Standard Accessories

Please check the package contents to ensure all standard accessories are present:

  • Speed / Cadence Sensor x 1
  • Rubber Mat (Flat x 1, Curved x 1)
  • Band (Large x 2, Medium x 2, Small x 2)
  • User Manual x 1
COOSPO BK467 Standard Accessories

Figure 2.1: Contents of the COOSPO BK467 package, including the sensor, rubber mats, various sized bands, and the user manual.

3. Setup

3.1. Battery Installation and Insulation Sheet Removal

The sensor comes with a pre-installed battery, but an insulation sheet must be removed before first use.

  1. Twist the battery cover counter-clockwise (in the 'OPEN' direction) using a coin.
  2. Carefully remove the battery cover and the battery.
  3. Remove the insulating sheet located beneath the battery.
  4. Reinsert the battery with the positive (+) side facing up.
  5. Replace the battery cover and twist it clockwise (in the 'CLOSE' direction) until secure.
Battery Insulation Sheet Removal

Figure 3.1: Diagram illustrating how to open the battery cover with a coin and remove the insulating sheet before first use.

3.2. Mode Switching (Speed or Cadence)

The BK467 sensor can operate in either Speed Mode or Cadence Mode. The mode is switched by reinstalling the battery.

  1. Open the battery cover and remove the battery as described above.
  2. Reinstall the battery. Observe the indicator light immediately after reinstallation:
    • If the BLUE indicator flashes, the sensor is in Cadence Mode.
    • If the RED indicator flashes, the sensor is in Speed Mode.
  3. If the desired mode is not active, remove and reinstall the battery again until the correct indicator light flashes.
  4. Securely close the battery cover.
Cadence Mode Blue LED, Speed Mode Red LED

Figure 3.2: The sensor displays a blue LED flash for Cadence Mode and a red LED flash for Speed Mode upon battery reinstallation.

Cadence Mode and Speed Mode Visual Guide

Figure 3.3: Visual guide showing the sensor in Cadence Mode (blue LED, installed on crank arm) and Speed Mode (red LED, installed on wheel hub).

3.3. Installation for Speed Mode

To measure speed, ensure the sensor is in Speed Mode (red indicator flashes) and install it on your bike's wheel axle.

  1. Buckle the curved rubber mat onto the back of the sensor.
  2. Bind the sensor with a large rubber band onto the wheel axle. Ensure it is securely fastened and does not interfere with wheel rotation.
Speed Mode Installation Steps

Figure 3.4: Step-by-step guide for installing the sensor in Speed Mode on the wheel axle using the curved rubber mat and a large band.

3.4. Installation for Cadence Mode

To measure cadence, ensure the sensor is in Cadence Mode (blue indicator flashes) and install it on your bike's pedal crank.

  1. Buckle the flat rubber mat onto the back of the sensor.
  2. Bind the sensor with a small rubber band onto the pedal crank. Ensure it is securely fastened and does not interfere with pedaling.
Cadence Mode Installation Steps

Figure 3.5: Step-by-step guide for installing the sensor in Cadence Mode on the pedal crank using the flat rubber mat and a small band.

4. Operating

4.1. Pairing with Devices and Apps

The COOSPO BK467 sensor supports both ANT+ and Bluetooth 4.0 for broad compatibility with various bike computers and smartphone applications.

  1. Ensure the sensor is correctly installed and in the desired mode (Speed or Cadence).
  2. Activate Bluetooth on your smartphone or turn on your bike computer.
  3. Open your preferred cycling app (e.g., CoospoRide, Strava, Wahoo Fitness) or navigate to the sensor pairing menu on your bike computer.
  4. Search for new sensors. The BK467 should appear in the list of available devices.
  5. Select the BK467 to pair. Once paired, the sensor will typically connect automatically for subsequent rides.

Compatible Devices and Apps:

  • ANT+ Compatible Devices: COOSPO, GARMIN, Wahoo, iGPSPORT, ZWIFT, ONELAP, BKOOL, TACX, BRYTON, and other ANT+ enabled bike computers.
  • Bluetooth Compatible Apps: CoospoRide, STRAVA, NIKE+, ENDOMONDO, RUNTASTIC PRO, WAHOO FITNESS, and other apps with speed/cadence features.
ANT+ and Bluetooth Compatibility

Figure 4.1: Chart illustrating the broad compatibility of the BK467 sensor with various ANT+ devices and Bluetooth applications.

CoospoRide App Interface

Figure 4.2: Example of the CoospoRide app interface displaying real-time cycling data from the sensor.

5. Maintenance

5.1. Battery Replacement

When the sensor's performance degrades or it stops transmitting data, it may be time to replace the battery. The BK467 uses a CR2032 coin cell battery.

  1. Twist the battery cover counter-clockwise using a coin to open.
  2. Remove the old CR2032 battery.
  3. Insert a new CR2032 battery with the positive (+) side facing up.
  4. Replace the battery cover and twist it clockwise until secure.
  5. Remember to check the mode (Speed or Cadence) after battery replacement by observing the LED flash.

5.2. Cleaning and Water Resistance

The BK467 sensor is IP67 waterproof, meaning it is protected from dust and can withstand immersion in water up to 1 meter for up to 30 minutes. This makes it suitable for use in various weather conditions, including rain.

  • To clean the sensor, wipe it with a soft, damp cloth.
  • Do not use abrasive cleaners or solvents, as these may damage the casing.
  • Ensure the battery cover is always securely closed to maintain water resistance.
IP67 Waterproof Rating

Figure 5.1: The sensor demonstrating its IP67 waterproof capability, suitable for use in wet conditions.

6. Troubleshooting

6.1. Common Issues and Solutions

  • Sensor not pairing:
    • Ensure the battery is correctly installed and has power.
    • Check if the sensor is in the correct mode (Speed/Cadence) by observing the LED flash.
    • Move the sensor closer to the receiving device.
    • Restart your bike computer or smartphone's Bluetooth.
  • Incorrect speed/cadence readings:
    • Verify the sensor is securely mounted and not moving during activity.
    • Ensure the sensor is in the correct mode for its installation location (Speed on wheel, Cadence on crank).
    • Check for any physical obstructions or interference.
  • Intermittent connection:
    • Replace the battery.
    • Ensure there are no strong electromagnetic interferences nearby.
    • Maintain a clear line of sight between the sensor and the receiving device if possible.

6.2. FCC Statement

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

  • Reorient or relocate the receiving antenna.
  • Increase the separation between the equipment and receiver.
  • Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
  • Consult the dealer or an experienced radio/TV technician for help.

Changes or modifications not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.

6.3. Waste Electrical Products

Waste electrical products should not be disposed of with household waste. Please recycle where facilities exist. Contact your local government or a retailer for additional information.

6.4. Product Handling Warnings

  • Do not open or modify the product.
  • Do not disassemble or attempt to service this product.
  • This product is safe under normal and reasonably foreseeable operating conditions.
  • If the product is operating improperly, call COOSPO support.
  • The product must be returned to the manufacturer for any service or repair.

7. Specifications

FeatureSpecification
Weight9.5 g
Battery Life300 hours
Battery TypeCR2032 220mAh
Waterproof RatingIP67
Wireless ConnectivityBluetooth & ANT+
Dimensions41 x 34 x 10 mm
Max Speed120 km/h
Max Cadence300 rpm
Working Temperature-10°C ~ 50°C
ColorBlack

8. User Tips

  • Dual Sensor Setup: For simultaneous speed and cadence tracking, many users purchase two BK467 sensors. Set one to Speed Mode and install it on the wheel axle, and set the other to Cadence Mode and install it on the pedal crank. Both can then transmit data to your compatible bike computer or app.
  • Mode Confirmation: Always double-check the LED color (blue for cadence, red for speed) immediately after reinstalling the battery to ensure the sensor is in your desired operating mode.
  • Easy Pairing: The BK467 is widely reported to pair seamlessly with popular bike computers from brands like Garmin (Edge series), Wahoo, iGPSPORT, and COOSPO (e.g., BC200, BC107).
  • Waterproof Reliability: Users have reported reliable performance even after riding in the rain and cleaning their bikes, thanks to the IP67 waterproof rating.

9. Warranty and Support

9.1. Disclaimer

  • The information contained in this manual is for reference only. The product described above may be subject to alteration owing to the manufacturer's continuing research and development plans, without making an announcement in advance.
  • We shall not make any statement or warranty about this manual.

9.2. Battery Statement and Warnings

WARNING: INGESTION HAZARD

  • This product contains a button cell or coin battery.
  • Death or serious injury can occur if ingested.
  • A swallowed button cell or coin battery can cause internal chemical burns in as little as 2 hours.
  • KEEP new and used batteries OUT OF REACH of CHILDREN.
  • Seek immediate medical attention if a battery is suspected to be swallowed or inserted inside any part of the body.

General Battery Safety:

  • Remove and immediately recycle or dispose of used batteries according to local regulations and keep away from children. Do NOT dispose of batteries in household trash or incinerate.
  • Even used batteries may cause severe injury or death. Call a local poison control center for treatment information.
  • Compatible battery type: CR2032. Nominal battery voltage: 3V.
  • Do not force discharge, recharge, disassemble, heat above 45°C or incinerate. Doing so may result in injury due to venting, leakage or explosion resulting in chemical burns.
  • Ensure the batteries are installed correctly according to polarity (+ and -).
  • Do not mix old and new batteries, different brands or types of batteries, such as alkaline, carbon-zinc, or rechargeable batteries.
  • Remove and immediately recycle or dispose of batteries from equipment not used for an extended period of time according to local regulations.
  • Always completely secure the battery compartment. If the battery compartment does not close securely, stop using the product, remove the batteries, and keep them away from children.

9.3. Further Support

For detailed inquiries, technical support, or warranty claims, please refer to the official COOSPO support channels or the comprehensive PDF user manual available at: COOSPO BK467 User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.