Heltec 21700 6S Battery Case

Contents

Heltec 21700 6S Battery Case User Manual

Model: 21700 6S Battery Case | Brand: Heltec

1. Introduction

This manual provides essential instructions for the safe and effective use of your Heltec 21700 6S Battery Case. This product is designed for DIY power wall battery boxes, offering a modular and easy-to-assemble solution for 21700 lithium-ion cells.

Heltec 21700 6S Battery Case with BMS board

Figure 1: Heltec 21700 6S Battery Case with BMS board

2. Safety Precautions

  • Always observe correct battery polarity as indicated on the circuit board. Incorrect installation can damage the device and batteries.
  • Do not short-circuit the battery terminals.
  • Use only 21700 lithium-ion batteries that are in good condition.
  • Ensure proper ventilation when assembling and operating battery packs.
  • Avoid exposing the battery case to extreme temperatures, direct sunlight, or moisture.
  • If using a BMS (Battery Management System), ensure it is correctly wired and functioning to prevent overcharge, over-discharge, and voltage imbalance.
  • It is recommended to use a dedicated charger for your battery pack. If using other chargers, ensure they are compatible and use a DC connector.
  • Do not exceed the recommended charging current of 1A per layer.

3. Package Contents

Please check the package for the following items:

  • Heltec 21700 6S Battery Holder (1P or 2P configuration)
  • Optional: 40A BMS board (if selected)
  • Connection cables (for multi-layer stacking)
  • M4 Copper pillars
  • Screws and nuts
Parts display including cables, copper pillars, screws, and nuts

Figure 2: Included parts for assembly

4. Setup and Assembly

4.1. Product Classification

The battery case is available in different configurations:

  • 6S1P: Six cells in series, one parallel string.
  • 6S2P: Six cells in series, two parallel strings.
  • 6S1P with 40A BMS: Six cells in series, one parallel string, integrated with a 40A Battery Management System.
Product classification showing 6S1P, 6S2P, and 6S1P with BMS 40A configurations

Figure 3: Available product configurations

4.2. Battery Installation

  1. Install the 21700 batteries directly into the holder.
  2. Ensure the direction and polarity of each battery match the symbols marked on the circuit board. Incorrect polarity can cause damage.
  3. Ensure the notch direction of all installed batteries is consistent.
Diagram showing correct battery installation polarity

Figure 4: Correct battery installation orientation

4.3. Assembly Steps

  1. After installing the batteries, screw on the M4 copper pillars to secure the layers.
  2. If stacking multiple layers, ensure the connection cables are properly installed between layers.
  3. Once all components are assembled and connections are confirmed, the unit is ready for use.

4.4. Wiring Diagram (6S Battery Box)

Refer to the diagram below for connection points:

Wiring diagram for 6S battery box showing charge/discharge ports, XT60, and other interfaces

Figure 5: 6S Battery Box Interface Layout

  • Charge and discharge cathode: Negative terminal for charging and discharging.
  • XT60 interface: High-current connector for power input/output.
  • Charge and discharge positive electrode: Positive terminal for charging and discharging.
  • Charge and discharge DC5.5*2.5 female: Standard DC jack for charging/discharging.
  • Line plugs: For balance leads or other control signals.
  • Copper column interface: Mounting points for structural support and electrical connections between layers.

5. Operating Instructions

Once assembled and wired correctly, the battery case functions as a power source. Connect your load or charger to the appropriate terminals (XT60, DC5.5*2.5, or main charge/discharge terminals) as per your application's requirements.

  • Voltage: The output voltage will correspond to the series configuration (e.g., 6S fully charged is 25.2V).
  • Current: The average instantaneous maximum current per layer is 20A. For long-term operation, it is recommended to keep the current below 10A per layer. Actual current capacity depends on the performance of the installed batteries.
  • Note: If there is no protection board layer (BMS), the output terminals will have no voltage, as the protection board is connected in series within the circuit. Without a BMS, the output is open.

6. Maintenance

  • Regularly inspect all connections for tightness and corrosion.
  • Keep the battery case clean and free from dust and debris.
  • Store the battery pack in a cool, dry place away from direct sunlight and extreme temperatures.
  • If the battery pack will not be used for an extended period, store it at approximately 50% charge to prolong battery life.

7. Troubleshooting

NOTE: Without a BMS, there will be no output from the battery case.

If the connection cannot be charged or there is no output, please carefully check the following points:

  1. First, check if there are any link errors in your wiring.
  2. After the initial connection, use a suitable charger and charge for a few seconds to activate the output.
  3. If charging is still not possible or there is no output, measure the voltage of each battery section separately. Check if there is a significant voltage difference between cells or if any cell combination exceeds 4.0V, which may prevent activation. If so, lower the voltage of the high cell(s) to around 3.7V and then combine.
Troubleshooting note regarding BMS and output issues

Figure 6: Important troubleshooting notes

8. Specifications

FeatureSpecification
Brand NameHeltec (ecoflypower)
Accessory TypeBattery Accessories
Voltage RangeLow voltage non-USB (below 75V DC, below 50V AC)
CertificationCE
Battery Type21700 Lithium-ion (not included)
Configuration6S1P, 6S2P, 6S1P with 40A BMS
6S1P Dimensions17.4 x 8.8 x 2.5 cm
6S1P Weight92g
6S2P Dimensions17.4 x 8.8 x 4.5 cm
6S2P Weight136g
6S1P 40A BMS Dimensions17.4 x 8.8 x 2.5 cm
6S1P 40A BMS Weight103g
Nominal Voltage (6S)21.6V (approx.)
Full Charge Voltage (6S)25.2V
Discharge Cut-off Voltage (6S)17.4V
Max Instantaneous Current (per layer)20A
Recommended Continuous Current (per layer)<10A

9. User Tips

  • Cell Length: When using protected 21700 cells, verify their length. Some protected cells can be longer (e.g., 76mm) than unprotected cells. Ensure the internal dimensions of the holder can accommodate these longer cells to avoid fitment issues or damage.
  • Modular Design: The stackable design allows for flexible capacity expansion. Ensure proper cable management and secure connections when adding layers.
  • Heat Dissipation: The design aids in heat dissipation. For high-current applications, ensure adequate airflow around the battery pack.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your retailer or the manufacturer directly. Keep your purchase receipt as proof of purchase.

© 2024 Heltec. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.