1. Introduction
This manual provides instructions for the installation, operation, and maintenance of your MIXSAS Car Dash Cam Suction Cup Holder, models 292 and 294. These holders are designed for specific 360 driving recorders, including the J501 and J501C models. Please read this manual carefully before use to ensure proper installation and safe operation.
2. Safety Information
- Ensure the suction cup is securely attached to a clean, smooth surface on your windshield or dashboard before mounting the dash cam.
- Do not obstruct your view of the road or any vehicle controls with the mounted dash cam.
- Avoid installing the holder in areas exposed to extreme heat or direct sunlight for prolonged periods, as this may affect the suction cup's performance.
- Regularly check the suction cup's adhesion, especially in varying temperature conditions.
- Keep out of reach of children.
3. Package Contents
The package typically includes the following components:
- 1 x Sucker Base
- 1 x 360 Special Ball (for dash cam connection)
- 1 x Cleaning Bag (Wet wipe #1, Dry wipe #2)
Figure 3.1: Package Contents
4. Specifications
| Feature | Detail |
|---|---|
| Brand Name | Mixsas |
| Material | PLASTICS (ABS/Silicone) |
| Installation Type | Wall-mounted (Suction Cup) |
| Special Features | Lightweight, Adjustable, Rotatable |
| Placement | Roof (typically windshield or dashboard) |
| Suitable Dashcam | 1st & 2nd Generation of 360 J501 / J501C |
| Sucker Diameter | 67mm |
| Ball Size | 16mm |
| Product Weight | Approx. 48g (main suction holder) |
| Package Dimensions (L x W x H) | 12cm x 10cm x 7cm |
| Package Weight | 0.15 kg |
5. Setup and Installation
Follow these steps to properly install your MIXSAS dash cam suction cup holder:
5.1. Prepare the Mounting Surface
- Open the cleaning bag. Use the "Wet 1" wipe to clean the desired installation area on your windshield or dashboard.
- Follow with the "Dry 2" wipe to ensure the surface is completely dry and free of dust or residue.
Video 5.1: Cleaning the mounting surface (0:00-0:12)
5.2. Assemble the Bracket and Attach Dash Cam
- Unscrew the groove nut cap from the suction cup base.
- Fit the groove of the dash cam's mounting interface into the bracket.
- Press the joint into the groove slightly and forcefully, adjust the angle as desired, and then tighten the nut cap properly to secure the dash cam.
Figure 5.2: Recorder Buckle Assembly
Important Note on Dash Cam Interface:
The MIXSAS holder supports two main interfaces for 360 DVRs. Model 292 is for the common interface (approximately 99% of users), while model 294 is for the less common interface. Please verify your dash cam's interface before attaching.
Figure 5.3: Dash Cam Interface Compatibility
5.3. Mount the Suction Cup
- Tear off the protective film from the suction cup.
- Paste the suction cup firmly onto the cleaned installation position on your windshield or dashboard.
- Pull down the suction cup gear (lever) to create a vacuum seal, securing the holder in place.
Video 5.4: Mounting the suction cup (0:12-0:30)
6. Operating Instructions
Once installed, the MIXSAS suction cup holder allows for flexible positioning of your dash cam:
- Angle Adjustment: The holder features a ball head and groove connection, allowing for multi-angle adjustment. Loosen the nut cap slightly to adjust the angle, then tighten it to secure the position.
- Reverse Installation: The design supports reverse installation, offering a variety of mounting methods and large angle adjustments to suit your preference and vehicle interior.
Figure 6.1: Primary and Secondary Adjustment
7. Maintenance
To maintain optimal suction performance:
- Cleaning the Suction Cup: If the suction cup becomes dirty or loses its stickiness, it can be washed with water. Simply rinse it under running water and allow it to air dry completely before reuse. This restores its repeatable adsorption properties.
- Storage: When not in use, store the holder in a clean, dry place away from direct sunlight and extreme temperatures.
Figure 7.1: Washing the Suction Cup
8. Troubleshooting
- Suction Cup Not Sticking:
- Ensure the mounting surface is clean, dry, and smooth. Use the provided cleaning wipes.
- Check for any air bubbles under the suction cup. Reapply, pressing firmly while engaging the lever.
- If the suction cup is dirty, wash it with water and let it air dry.
- Extreme temperatures can affect suction. Try mounting in moderate conditions.
- Dash Cam is Loose:
- Ensure the groove nut cap is fully tightened after adjusting the dash cam's angle.
- Verify that your dash cam's interface is compatible with the specific holder model (292 or 294).
9. User Tips
- For best results, mount the suction cup on a smooth, non-porous surface like glass.
- When removing the holder, gently lift the suction cup lever to release the vacuum seal, then peel it off. Avoid pulling forcefully.
- Consider the dash cam's cable routing during installation to prevent obstruction and ensure a tidy setup.
10. Warranty and Support
For warranty information or technical support, please refer to the seller's official website or contact their customer service directly. A user manual in PDF format is also available for download: MIXSAS Dash Cam Holder User Manual (PDF).