Nasedal R500

Contents

Nasedal R500 LVLP Spray Gun Instruction Manual

Model: R500 | Brand: Nasedal

1. Important Safety Instructions

Read this manual carefully and understand it completely. Basic safety precautions should always be strictly followed to prevent damage to the tool and injury to the operator. Retain this manual for future reference. Pay close attention to the Technical Data.

  1. Toxic vapors produced by spraying certain materials can cause intoxication and serious damage to health. Always wear protective respirator, eyewear, and gloves to prevent toxic hazard solvent and paint from coming into contact with your eyes or skin.
  2. Never use oxygen, combustible, or any other bottled gas as an air source, as this could cause an explosion or serious personal injury.
  3. Fluid and solvent can be highly flammable or combustible. Use in a well-ventilated spray booth and avoid any ignition sources such as smoking and open flames.
  4. Disconnect the tool from the air supply hose before carrying out any tool maintenance and when not in use.
  5. Use clean, dry, and regulated compressed air rated at 2.5-3.5 bar. Never exceed a maximum operating pressure of 6 bar.
  6. Only use parts, nozzles, and accessories recommended by the manufacturer.
  7. Before operating the tool, make sure all screws and caps are securely tightened to prevent leaking.
  8. Inspect daily for free trigger movement and nozzle to ensure the tool is fully operational.
  9. Never use solvent which can chemically react with aluminum and zinc parts.
  10. Never modify the tool.

2. Product Overview and Components

The Nasedal R500 LVLP Spray Gun is designed for efficient and smooth paint application across various surfaces. It features a durable construction with adjustable controls for precise results.

Nasedal R500 LVLP Spray Gun and included accessories
Figure 2.1: Nasedal R500 LVLP Spray Gun with 600cc cup, wrench, cleaning brush, and air connector.
Labeled diagram of R500 spray gun components and specifications
Figure 2.2: Detailed view of the R500 spray gun components and key specifications.

2.1 Parts List

The following table details the components of the R500 LVLP Spray Gun:

No. Description No. Description No. Description
1Atomization16Washer31Fluid Adj. Joint
2Nut17Spring32Spring
3Spring18Washer33Joint
4Fluid Cap Washer19Spring34Fluid Adj. Knob
5Fluid Nozzle20O-ring35Trigger
6Fluid Nozzle Joint21Air Adj. Knob36Trigger Lever I
7Joint Washer22Air Adj. Screw37Trigger Lever II
8Joint Washer23Air Inlet Valve38Fluid Adj. Needle
9Direction Screw24Air Inlet Joint39Filter
10Washer25Phillips Screw40Cup
11Gun Body26Pattern Adj.41Cup Cover
12Direction Screw27Pattern Adj. Screw42Ventilator Head
13Washer28Washer43Tool Wrench
14Switch Knob29Pattern Adj. Knob44Brush
15Air Valve Body30Snap Retainer

3. Specifications

Attribute Value
Model NumberR500
TypeLVLP (Low Volume Low Pressure)
ApplicationPaint Spray Gun (Automotive, Home DIY, Furniture Painting)
Power TypePneumatic
Feed TypeGravity
Standard Nozzle Diameter1.3mm
Cup Volume600cc
Operating Pressure2.0-3.5 bar
Pattern Width180-280mm
Air Consumption3.0-3.9cfm
Paint Consumption130-170 ml/min
Paint Ratio>= 65%
CertificationCE
Battery IncludedNo
High-concerned chemicalNone
Dimensions of the R500 spray gun and paint cup
Figure 3.1: Dimensions of the R500 spray gun and 600cc paint cup.

4. Setup

Before first use, ensure all components are clean and properly assembled.

  1. Unpack: Carefully remove all items from the packaging. Verify that all parts listed in Section 2.1 are present.
  2. Attach Air Connector: Connect the appropriate air quick connector to the air inlet of the spray gun.
  3. Install Air Pressure Regulator (Optional but Recommended): If using an external air pressure regulator, attach it to the air inlet of the spray gun. This allows for precise control of air pressure.
  4. Air pressure regulator with gauge and filter
    Figure 4.1: Example of an air pressure regulator with gauge and filter for optimal performance.
  5. Attach Paint Cup: Securely screw the 600cc plastic paint cup onto the top of the spray gun.
  6. Connect Air Hose: Connect your compressed air supply hose to the air inlet of the spray gun (or to the air pressure regulator if used).
  7. Prepare Paint: Mix your paint according to the manufacturer's instructions. Ensure it is suitable for LVLP spray guns and has a middle viscosity. Strain the paint to remove any impurities that could clog the nozzle.
  8. Fill Paint Cup: Pour the prepared paint into the 600cc gravity feed cup. Securely close the cup cover.

5. Operating Instructions

The R500 LVLP Spray Gun is designed for efficient and smooth application. Proper technique and adjustment are key to achieving desired results.

5.1 Power Source

This tool requires clean, dry, and compressed air rated at a regulated pressure of 2.5-3.5 bar to operate. The compressed air contains moisture and other contaminants. Using a filter will remove most of these foreign matters. Use a filter and a pressure regulator as close to the tool as possible.

CAUTION: Air pressure should be regulated to 2.5-3.5 bar. Air pressure which is too low or too high will damage the tool and influence the painting effect.

5.2 Adjusting the Spray Gun

The R500 features three adjustable valve knobs for precise control:

Diagram showing 3 adjustable valve knobs for spray width, paint flow, and air volume
Figure 5.1: Location of the three adjustable valve knobs.
  • Spray Width Control Knob: Adjusts the width of the spray pattern. Turn clockwise for a narrower pattern, counter-clockwise for a wider pattern.
  • Paint Flow Control Knob: Regulates the amount of paint released. Turn clockwise to decrease paint flow, counter-clockwise to increase.
  • Air Volume Adjust Valve: Controls the air pressure at the gun. Adjust to achieve the recommended operating pressure of 2.5-3.5 bar.

The 360° adjustable copper air cap allows for versatile spray directions.

Close-up of 360 degree adjustable copper air cap and stainless steel nozzle and needle
Figure 5.2: Close-up of the adjustable air cap and stainless steel nozzle.

5.3 Spraying Technique

For best results, maintain a consistent distance and speed during spraying.

  1. Test Spray: Always test the spray pattern and paint flow on a scrap piece of material before applying to your actual project. Adjust the knobs until the desired pattern and coverage are achieved.
  2. Distance: Hold the spray gun approximately 180-280mm (7-11 inches) from the surface.
  3. Movement: Move the gun parallel to the surface at a steady speed. Overlap each pass by about 50% to ensure even coverage.
  4. Trigger Usage: The trigger has two stages: Trigger 1 for blowing air only, and Trigger 2 for spraying paint. Engage Trigger 1 first, then fully depress for Trigger 2 to spray. Release Trigger 2 at the end of each stroke, then release Trigger 1.
  5. Person using the R500 spray gun to paint a car surface
    Figure 5.3: Demonstrating proper spray gun usage for a smooth coating.
  6. Avoid Overspray: To avoid excessive paint output and achieve the desired pattern, use the lowest effective pressure.

The R500 is suitable for various applications including automotive, home DIY, and furniture painting projects.

Examples of usage scenarios for the spray gun including wall, furniture, and car painting
Figure 5.4: Usage scenarios for the Nasedal R500 LVLP Spray Gun.

6. Maintenance

Regular cleaning and maintenance will prolong the life of your spray gun and ensure consistent performance.

  1. Immediate Cleaning: After each use, immediately empty any remaining paint from the cup. Pour a small amount of appropriate cleaning solvent into the cup.
  2. Flush Gun: Spray the solvent through the gun until it runs clear. This flushes out paint from the fluid passages.
  3. Disassemble: Disconnect the air supply. Carefully disassemble the air cap, fluid nozzle, and needle.
  4. Clean Components: Use the provided cleaning brush and solvent to thoroughly clean all disassembled parts. Pay special attention to the air cap holes and the fluid nozzle.
  5. Clean Gun Body: Wipe down the exterior of the gun body with a solvent-dampened cloth.
  6. Lubricate: Apply a small amount of lubricant (compatible with your paint type) to the needle packing and air valve components as needed.
  7. Reassemble: Reassemble the gun, ensuring all parts are securely tightened to prevent leaks.
  8. Storage: Store the clean and dry spray gun in a safe place, away from dust and extreme temperatures.

7. Troubleshooting

If you encounter issues with your spray gun, refer to the following common problems and solutions:

Problem Possible Cause Solution
Uneven Spray Pattern Clogged air cap or fluid nozzle; incorrect air pressure; improper gun distance/speed. Clean air cap/nozzle; adjust air pressure to 2.5-3.5 bar; maintain consistent distance and speed.
Paint Dripping from Nozzle Loose fluid nozzle; worn needle packing; paint too thin. Tighten fluid nozzle; replace needle packing; thicken paint or adjust fluid control.
No Paint Flow Clogged fluid passage; empty paint cup; fluid control knob closed. Clean fluid passage; refill paint cup; open fluid control knob.
Excessive Overspray Air pressure too high; gun too far from surface; paint too thin. Reduce air pressure; move gun closer to surface; thicken paint.
Rough Finish Paint too thick; insufficient atomization; dirty air cap. Thin paint; increase air pressure (within limits); clean air cap.

8. User Tips

  • For a smooth and even spray coating, ensure your paint is properly thinned and the air pressure is within the recommended 2.5-3.5 bar range.
  • The 600cc cup volume and gravity feed design contribute to easy application and a professional finish.
  • Remember to clean the spray gun thoroughly after each use to prevent clogging and maintain optimal performance.

9. Frequently Asked Questions (FAQ)

Q: What is the function of this spray gun?
A: Its primary function is to provide a smooth and even spray coating for various painting applications.
Q: What are the benefits of using it?
A: Benefits include achieving a professional finish, easy application, and CE certification for quality assurance. Its LVLP design also helps save paint and reduce overspray.
Q: What is the power mode of it?
A: It operates using a pneumatic (compressed air) power type.
Q: What category does it belong to?
A: It belongs to the category of spray guns, specifically an LVLP type.
Q: What are the highlights of it?
A: Key highlights include a 600cc cup volume, gravity feed type, and a 1.3mm stainless steel nozzle for fine atomization.

10. Product Video

Watch this video for a visual overview of the Nasedal R500 LVLP Spray Gun and its features.

Video 10.1: Nasedal R500 LVLP Spray Gun Product Overview.

11. Warranty and Support

This product is covered by a standard manufacturer's warranty. For warranty claims, technical support, or replacement parts, please contact the seller or manufacturer directly. Refer to the original purchase documentation for specific warranty terms and contact information.

A comprehensive user manual in PDF format is available for download: User manual (PDF).

© 2024 Nasedal. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.