VaneAims FXBY6

Contents

VaneAims FXBY6 Series Push Button Switch Instruction Manual

Model: FXBY6

1. Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of the VaneAims FXBY6 Series 22mm Push Button Switches. These switches are designed for industrial electrical control applications, featuring an innovative body structure, strong security, and space-saving slim contact block types. The FXBY6 series includes various configurations such as Emergency Stop Switches, All-in-one Indicated Lamps, and Key Selector Switches, available in momentary or latching operation with LED illumination options for different voltages (6V, 12V, 24V, 110V, 230V).

Assortment of VaneAims FXBY6 push button switches in red, yellow, blue, green, and white.
Figure 1: VaneAims FXBY6 Push Button Switches (Various Colors)

2. Safety Precautions

To ensure safe operation and prevent electric shock or fire, please observe the following precautions:

  • Power Disconnection: Always disconnect the power supply before any installation, disassembly, wiring, or maintenance inspection of the FXBY6 series control components.
  • Bulb Replacement: Use the designated bulb replacement tool to avoid burns when replacing bulbs.
  • Wiring: Ensure that the wire used meets the specified voltage and current requirements. Tighten M3.5 wiring screws to a torque of 1.0 Nm. Avoid using terminals with slack to prevent overheating and potential fire hazards.
  • LED Lighting Components:
    • Do not exceed the rated voltage, as this can cause LED deterioration, reduced brightness, color change, or non-illumination.
    • If external noise, transient voltage, or current is present, it can damage the LED. Consider using RC elements or surge absorbers for protection.
    • For AC/DC rated LEDs, they can be used within ±10% of the rated voltage.
    • When using switching power supplies, ensure a stable voltage.
    • For rechargeable batteries, ensure the voltage remains within 10% of the LED's rated voltage, especially during and immediately after charging.
    • Full-wave rectification circuits do not require a rectifier diode bridge. If used, the rectifier diode will reduce voltage and diminish brightness.
    • Single-phase half-wave rectification is not suitable for LED power supply; use a constant voltage DC power supply.
  • Marking Plate Usage: When cutting panels without anti-rotation, use flat-nose pliers to snap off the 'A' part of the marking plate.
  • Key Selector Switch: Ensure the key is fully inserted into the keyhole before operating the switch. Operating with a partially inserted key may cause damage.
  • General Handling: Avoid excessive shock or vibration to the switch, as it may lead to deformation, damage, or poor performance.

3. Product Overview

The VaneAims FXBY6 series offers a range of 22mm control components, including push button switches, indicator lamps, and key selector switches. Key features include:

  • Innovative Design: Body structure designed for strong security and space-saving.
  • Compliance: Complies with international standards.
  • Secure Locking Structure: Features direct open-circuit action function and security button design for emergency stop switches.
  • High Brightness: All-in-one indicated lamps offer high brightness.
  • Compact Design: Only 42mm of extension behind the panel, reducing overall depth.
  • Simple Operation: Push-pull or rotate to reset functionality.
  • Lampshade Types: Available in flat head shape (text marking type) and round/convex shape.
  • Key Selector Switch: Wide variety of operation types, key pull-out positions and circuits.
  • High Reliability: Designed for durability with a self-cleaning sliding structure contact.
  • Enhanced Security: Terminal sleeve all-in-one finger safety type terminals (IP20 protection, IP65 before the panel) protect against electrocution hazards.
Close-up of a red VaneAims push button switch with NC contact block details.
Figure 2: Red Push Button Switch (NC Contact Block)
Close-up of a yellow VaneAims push button switch with NO contact block details.
Figure 3: Yellow Push Button Switch (NO Contact Block)

Manufacturing Process

The following video demonstrates the automated manufacturing process of VaneAims switches, highlighting the precision and quality control involved.

Video 1: VaneAims Switch Manufacturing Process

4. Specifications

General Electrical Characteristics

ParameterValue
Rated Insulation Voltage600V
Rated Energization Current10A
Minimum Applicable Load3V AC/DC (reference value)
Contact MaterialSilver contacts
Mounting Diameter22MM
MaterialPlastic
Item TypeSWITCHES
Is Smart DeviceNo
OriginMainland China

Rated Voltage and Current (AC 50/60Hz)

Load Type24V120V240V380V
Resistive Load (AC-12)10A10A6A2A
Inductive Load (AC-15)10A6A3A1.9A

Rated Voltage and Current (DC)

Load Type24V120V240V380V
Resistive Load (DC-12)8A2.2A1.1A-
Inductive Load (DC-13)4A1.1A0.55A-

Performance Specifications

ParameterValue
Operating Ambient Temperature-20°C to +55°C (No icing)
Operating Ambient Humidity45% to 85% (No condensation)
Storage Ambient Temperature-45°C to +80°C
Storage Ambient HumidityBelow 95%RH
Protection Level (Front Panel)IP65 (IEC 60529)
Protection Level (Terminal)IP20 (IEC 60529)
Insulation Resistance100MΩ or more (500V DC Megohmmeter)
Withstand Voltage (Contact Block)2,500V AC for 1 minute
Withstand Voltage (Indicator Light)2,000V AC for 1 minute
Vibration Resistance (Mistake Action)10-500Hz, 0.35mm amplitude, 50m/s² acceleration
Vibration Resistance (Durability)5-55Hz, 0.5mm amplitude, 30Hz, 1.5mm amplitude
Impact Resistance (Mistake Action)150 m/s²
Impact Resistance (Durability)1,000 m/s² (for indicator light, pushbutton, selector switch, key selector switch)
Mechanical Lifetime (Emergency Stop)250,000 times (single-contact only)
Mechanical Lifetime (Self-replicating)5 million times (single-contact), 1 million times (double contact)
Mechanical Lifetime (Self-locking)250,000 times (single-contact)
Mechanical Lifetime (Selector Switch)250,000 times (single-contact), 10,000 times (double contact)
Electrical Lifetime (Emergency Stop)100,000 times (single-contact only)
Electrical Lifetime (Pushbutton/Selector)100,000 times (single-contact), 50,000 times (double contact)

For detailed LED lighting component specifications, including current consumption for various voltages and colors, please refer to the complete PDF manual.

5. Installation and Setup

Panel Mounting

  1. First, remove the contact block from the component. For transformer type indicators, also remove the transformer from the lighting components.
  2. Unscrew the locking ring from the operating part.
  3. Insert the operating part into the mounting hole on the front of the panel. The mounting hole diameter is 22mm, and the panel thickness should be between 0.8mm and 6.0mm.
  4. Tighten the locking ring from the back of the panel.
  5. Finally, install the contact block to the operating section.

Note: Use a locking ring wrench (MW9Z-T1) for tightening the operating section to the panel. Recommended torque is up to 2.0 Nm. Do not overtighten. For detailed dimensional drawings, please consult the full PDF manual.

Side view of a green VaneAims push button switch, showing the contact block and locking mechanism.
Figure 4: Green Push Button Switch Assembly

Contact Block Removal and Installation

  1. To remove, toggle the pin lock lever to the left and pull out the contact block.
  2. To install, align the TOP mark on the operation section with the TOP mark on the contact block and insert it. Then, toggle the pin lock lever in the opposite direction to secure.

Transformer Disassembly and Installation

  1. Insert a Phillips screwdriver (width below 5mm) into the inner locking hole of the transformer component to release the latch, then pull out the transformer.
  2. When installing, align the TOP mark of the lighting component with the latching direction of the transformer component and push it in.

Wiring

Ensure proper wire selection and connection for optimal performance and safety.

  • The wire cross-sectional area should be 2.0mm².
  • For fork crimp terminals, install an insulation tube or use a crimp terminal with insulation cladding. Ensure the terminal is fully inserted.
  • When connecting wires with two bar terminals, use a bar terminal without an insulation sheath.
  • For single stranded wires, standardize the wire size when using two wires for direct connection.

Bulb Installation (for illuminated types)

  1. Insert the lamp head into the bulb replacement tool.
  2. Align the mounting pins on the bottom of the bulb with the socket groove.
  3. Insert the bulb and rotate it clockwise.

6. Operation

Push Button Switches

The push button switches offer simple and convenient operation:

  • Momentary Type: The switch returns to its original state when the button is released.
  • Latching Type: The switch remains in its pressed state until it is manually reset. To reset, press the lockout, pull out, or rotate the button. Both pull-out and rotation methods can be used for resetting, offering flexibility and safety.

Key Selector Switches

Key selector switches are available with various operation types and key pull-out positions. These include latching, reset from right, reset from left, and bi-directional reset functionalities. For specific model configurations and key extractable positions (e.g., 2-bit or 3-bit types), please refer to the detailed tables and diagrams in the full PDF manual. Always ensure the key is fully inserted before operation to prevent damage.

7. Maintenance

Bulb Replacement

Replacement bulbs can be changed from the front of the panel using a bulb replacement tool (OR-55), or by removing the contact block from the back of the panel. To remove the bulb from the front, insert the tool into the lamp head and turn it counterclockwise while pressing lightly.

Text Marking Plate

Text and symbols for illuminated push button switches and indicator lights can be engraved on the built-in text marking plate or inserted as a film with printed text marks inside the lampshade. Characters must be engraved within the lettering range, within a depth of 0.5 mm. The text marking plate is made of white acrylic resin. Polyester film (0.1 mm thick) can be used for printed text marks; two 0.1 mm films or one 0.2 mm film can be installed.

Spare Parts

Spare keys for key selector switches are available (FXBY6-K).

Close-up of a yellow illuminated push button switch.
Figure 5: Yellow Illuminated Push Button Switch

8. Troubleshooting

LED Lighting Issues

  • External Noise: If external noise causes LEDs to dim or fail, insert a noise suppression device (e.g., RC elements or surge absorbers) between the X1 and X2 terminals.
  • Dark Spot Lights:
    • If the LED remains dimly lit even when the output is off, it may be due to leakage current through the transistor or contact protection circuit. A shunt resistor connected in parallel with the LED can help prevent this.
    • If the LED is illuminated by transistor output, ensure appropriate measures are taken to prevent dark spots.

Contact Bounce

When resetting latching type switches (push-pull or rotary reset), the main contact (NC contact) may bounce back. Consider preventive measures if this is critical for your application (reference value: 20ms).

9. User Tips

  • Always verify the voltage rating of your specific switch model before connecting it to power.
  • For illuminated switches, ensure the correct bulb type (LED or incandescent) and voltage are used to prevent damage and ensure proper illumination.
  • When installing multiple switches, ensure adequate spacing for ease of wiring and maintenance.
  • Regularly check wiring connections for tightness to prevent intermittent operation or safety hazards.

10. Warranty and Support

For warranty information, technical support, or service inquiries, please contact your authorized VaneAims distributor or the seller directly. Keep your purchase receipt and product model information handy for faster assistance.

A comprehensive PDF manual with detailed diagrams and specific model configurations is available for download: View User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.