1. Introduction
1.1. Preface
Thank you for purchasing the Baofeng UV-S22 PRO V2 Amateur Portable Radio. This device offers high performance and stable wireless two-way radio communication, featuring IP68 waterproofing, specifically designed for various environments including maritime and shipping use. Please read this manual carefully before use to ensure maximum performance from your radio.
1.2. Safety Information
The following safety precautions must always be observed during operation, service, and repair of this equipment:
- This equipment shall be serviced by qualified technicians only.
- Do not modify the radio for any reason.
- Use only supplied or approved batteries and chargers.
- Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with your skin, a minor burn can result.
- Turn off your radio prior to entering any area with explosive and flammable materials.
- Do not charge your battery in a location with explosive and flammable materials.
- To avoid electromagnetic interference and/or compatibility conflicts, turn off your radio in any area where posted notices instruct you to do so.
- Turn off your radio before boarding an aircraft. Any use of a radio must be in accordance with airline regulations or crew instructions.
- Turn off your radio before entering a blasting area.
- For vehicles with an air bag, do not place a radio in the area over an air bag or in the air bag deployment area.
- Do not expose the radio to direct sunlight over a long time, nor place it close to heating source.
- When transmitting with a portable radio, hold the radio in a vertical position with the microphone 3 to 4 centimeters away from your lips. Keep antenna at least 2.5 centimeters away from your body when transmitting.
WARNING: If you wear a radio on your body, ensure the radio and its antenna are at least 2.5 centimeters away from your body when transmitting.
2. Features and Functions
The Baofeng UV-S22 PRO V2 is an IP68 dust and waterproof two-way radio. It maintains full functionality even after 30 minutes submerged in one meter of water, ensuring reliability in wet environments. It also boasts drop and rolling resistance.
- IP68 Waterproof and Dustproof: Submersible up to 1 meter for 30 minutes.
- High Power Output: 10W maximum power, with selectable 1W, 5W, and 10W options.
- Dual-Band Handheld Transceiver: Supports VHF (136-174MHz) and UHF (400-520MHz) frequencies.
- FM Radio: Commercial FM radio receiver (65 MHz - 108 MHz).
- Memory Channels: Up to 128 memory channels.
- Cross Band Reception/Transmission: Allows communication across different frequency bands.
- Display: LCD with display function menu, showing channel number, frequency, channel name, etc.
- CTCSS & DCS: Continuous Tone-Coded Squelch System and Digital Coded Squelch for private group communication.
- VOX Function: Voice Operated Transmission for hands-free operation.
- DTMF Emergency Alarm: Digital Tone Multi-Frequency emergency alarm.
- ANI Code: Automatic Number Identification.
- Frequency Step: Selectable steps including 2.5/5/6.25/10/12.5/20/25/50 kHz.
- Frequency Reverse: For repeater use.
- Battery Saving Function: "SAVE" mode to prolong battery life.
- Emergency SOS: Sound and light alarm.
- Programmable: Via PC for customized settings.
- Bandwidth: Selectable Broadband (Wide 25KHz) / Narrowband (Narrow 12.5KHz).
- LED Flashlight: Built-in high brightness LED flashlight for illumination in dark environments.
- Type-C Charging: Modern and convenient charging port.
3. Package Contents
Carefully unpack the transceiver and verify all items are present. If any items are missing or damaged, contact your dealer immediately.
- 1 x Portable Radio (UV-S22 PRO V2)
- 1 x Antenna
- 1 x Li-ion Battery Pack
- 1 x LI-ion Charger (Type-C)
- 1 x Belt Clip
- 1 x Lanyard
- 1 x User's Manual
Note: Items included in the package may differ based on the country of purchase or specific bundle. Headsets and other accessories may be sold separately.
4. Setup
4.1. Installing the Antenna
Install the antenna by screwing it clockwise onto the top of the radio until it stops. Always hold the antenna by its base when installing or removing it, not by the top.
Important: If using an external antenna, ensure its SWR (Standing Wave Ratio) is 1.5:1 or less to prevent damage to the transceiver's final transistors. Never transmit without an antenna connected.
4.2. Installing the Belt Clip
If needed, attach the belt clip to the rear of the battery compartment cover using the provided screws. Avoid using glue to secure the screws, as solvents in glue can damage the battery casing.
4.3. Micro-Headset Installation (Optional)
Plug the external micro-headset connector into the 'SP. & MIC' jack on the side of the transceiver.
4.4. Battery Installation and Removal
Installation: Align the battery with the guide rails on the aluminum chassis and slide it upwards until a "click" is heard, indicating it's locked into place. Ensure the battery bottom is about 1 to 2 centimeters below the radio's body for proper contact.
Removal: Turn off the radio. Slide the battery latch at the bottom of the radio's body in the direction indicated by the arrow. Slide the battery down for about 1 to 2 centimeters, then remove it from the radio's body.
5. Battery Charging
Use only the charger specified by the manufacturer. The charger's LED indicates the charging progress:
| Charging Status | LED Indication |
|---|---|
| Standby (no-load) | Red LED flashes, Green LED glows |
| Charging | Red LED solidly glows |
| Fully Charged | Green LED solidly glows |
| Error | Red LED flashes, Green LED glows |
5.1. Battery Information and Care
- Initial Use: New batteries are shipped uncharged. Charge for 5 hours before initial use. Maximum capacity is achieved after three full charge/discharge cycles.
- Charging Temperature: Charge between 5°C and 40°C. Temperatures outside this range may cause battery leakage or damage.
- Charging with Radio: Turn off the radio when charging a battery attached to it to ensure a full charge.
- Wet Batteries: Never charge a wet battery. Dry it with a soft cloth first.
- Battery Lifespan: Batteries will eventually wear out. If operating time is noticeably shorter, it's time for a new battery.
- Storage: Fully charge the battery before long-term storage to prevent over-discharge. Recharge Li-ion batteries after several months of storage. Store in a cool, dry place at room temperature.
WARNING: Only use manufacturer-specified batteries and chargers. Do not dispose of batteries in fire, disassemble them, or dispose of them as household waste. Follow local recycling regulations.
6. Basic Operation
6.1. Radio On/Off and Volume Control
Rotate the PWR/VOL Switch clockwise to turn the radio on. You will hear a "Beep" sound and the current channel will be reported. Continue rotating clockwise to increase volume, or counter-clockwise to decrease it. Rotate fully counter-clockwise until a "click" is heard to turn the radio off.
6.2. Transmit and Receive
Select the desired channel or enter the frequency. Press and hold the PTT (Push-To-Talk) button to transmit, then speak into the microphone. Release the PTT button to receive. The LCD will show 'L', 'M', or 'H' indicating low, mid, or high power output during transmission.
6.3. VOX (Voice Operated Transmission)
The VOX function allows hands-free transmission by detecting your voice. Transmission starts automatically when you speak and ends when you stop. Adjust the VOX Gain level (1-10, 10 being most sensitive) in the menu to ensure smooth operation. To activate/deactivate, navigate to Function 4 in the menu, select the desired level or OFF, and confirm.
6.4. AUTOLK (Keypad Lock)
The transceiver offers both auto lock and manual lock. When auto lock is enabled, the keypad will lock after a few seconds of inactivity. To manually lock/unlock, press and hold [MENU] + number key 24, then select ON or OFF.
6.5. VFO/Channel Mode
To switch between VFO (Frequency) mode and Channel mode, turn off the radio, then press [MENU] and rotate the sound knob to turn on the radio. The display will show either the frequency (VFO mode) or channel number (Channel mode). You can also use the [EXIT/AB] key to switch between Channel A and Channel B, or between FM radio bands (65-75MHz/76-108MHz).
6.6. Selecting a Frequency or Channel
Use the [▲] or [▼] keys to select the desired frequency or channel. Press and hold these keys for fast scrolling. In VFO mode, frequencies can be entered directly using the numeric keypad.
7. Advanced Features
7.1. TDR (Dual Watch/Dual Reception)
This feature allows monitoring two frequencies (A and B) simultaneously. The transceiver periodically checks for signals on the scheduled frequency. If a signal is received, the unit will stay on that frequency until the signal disappears. To activate/deactivate, press [MENU] + [7TDR], then select ON or OFF.
7.2. MEM-CH (Stored In Memory Channel)
The transceiver has 128 memory channels (000 to 127). To store a frequency and its parameters (RX/TX frequency, CTCSS/DCS, RF Power, Bandwidth, etc.), input the desired settings in frequency mode or standby, then use the menu to save it to a channel.
7.3. DEL-CH (Delete Channel)
To delete a memory channel, press [MENU] + [Number key 28], then select the channel you wish to delete and confirm.
7.4. CTCSS/DCS Scanning
To find the correct CTCSS/DCS tone for a communication, ensure the radio is in VFO mode and Dual Standby is off. Go to MENU 11, press [MENU], then [*/SCAN]. The radio will scan for CTCSS/DCS tones. Once a tone is found, press [MENU] to store it.
Note: Using CTCSS or DCS does not guarantee complete confidentiality of communication.
| NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) | NO | Tone (Hz) |
|---|---|---|---|---|---|---|---|---|---|
| 1 | 67.0 | 11 | 94.8 | 21 | 131.8 | 31 | 171.3 | 41 | 203.5 |
| 2 | 69.3 | 12 | 97.4 | 22 | 136.5 | 32 | 173.8 | 42 | 206.5 |
| 3 | 71.9 | 13 | 100.0 | 23 | 141.3 | 33 | 177.3 | 43 | 210.7 |
| 4 | 74.4 | 14 | 103.5 | 24 | 146.2 | 34 | 179.9 | 44 | 218.1 |
| 5 | 77.0 | 15 | 107.2 | 25 | 151.4 | 35 | 183.5 | 45 | 225.7 |
| 6 | 79.7 | 16 | 110.9 | 26 | 156.7 | 36 | 186.2 | 46 | 229.1 |
| 7 | 82.5 | 17 | 114.8 | 27 | 159.8 | 37 | 189.9 | 47 | 233.6 |
| 8 | 85.4 | 18 | 118.8 | 28 | 162.2 | 38 | 192.8 | 48 | 241.8 |
| 9 | 88.5 | 19 | 123.0 | 29 | 165.5 | 39 | 196.6 | 49 | 250.3 |
| 10 | 91.5 | 20 | 127.3 | 30 | 167.9 | 40 | 199.5 | 50 | 254.1 |
Table 1: CTCSS Tones (Hz)
| No | Code | NO | Code | NO | Code | NO | Code | NO | Code |
|---|---|---|---|---|---|---|---|---|---|
| 1 | D023N | 22 | D131N | 43 | D251N | 64 | D371N | 85 | D532N |
| 2 | D025N | 23 | D132N | 44 | D252N | 65 | D411N | 86 | D546N |
| 3 | D026N | 24 | D134N | 45 | D255N | 66 | D412N | 87 | D565N |
Table 2: DCS Codes
7.5. Repeater Tail Tone
Repeaters receive on one frequency and retransmit on another. The "courtesy tone" (beep) confirms the repeater has received your transmission. MENU 35, 36, and 37 are helpful for repeater use. MENU 35 and 36 should generally be OFF. For MENU 37, a setting of 5 (out of 1-10) is recommended.
7.6. SOS Emergency Alarm
Long press the [SOS] button to activate the emergency alarm. The green and red lights will flash, and the hand lamp will shine. Press [SOS] again to deactivate. In emergency alarm mode, only [PTT] and [SOS] keys are active. The alarm will stop if the radio receives a transmission.
8. Technical Specifications
8.1. General
| Frequency Range: | 65MHz-108MHz (Commercial FM radio reception only), VHF: 136-174MHz (Rx/Tx), UHF: 400-520MHz (Rx/Tx) |
| Memory Channels: | Up to 128 channels |
| Frequency Stability: | 2.5ppm |
| Frequency Step: | 2.5kHz/5kHz/6.25kHz/10kHz/12.5kHz/20kHz/25kHz |
| Antenna Impedance: | 50 Ω |
| Operating Temperature: | -20°C to +60°C |
| Supply Voltage: | Rechargeable Lithium-Ion mAh 7.4V/1800 |
| Consumption in Reception: | 8000mA |
| Consumption in Transmission: | ≤1.4A |
| Mode of Operation: | Simplex or semi-duplex |
| Duty Cycle: | 03/03/54 min. (Rx / Tx / Standby) |
| Dimensions: | 185mm x 115mm x 102mm |
| Weight: | 490g (approximate) |
8.2. Transmitter
| RF Power: | 15W |
| Type of Modulation: | FM |
| Emission Class: | 16K0F3E/11K0F3E (W/N) |
| Maximum Deviation: | ≤±5 kHz/≤±2.5 kHz (W/N) |
| Spurious Emissions: | <-60 dB |
8.3. Receiver
| Receiver Sensitivity: | 0.2 u V (at 12 dB SINAD) |
| Intermodulation: | 60 dB |
| Audio Output: | 1W |
| Spurious Radiation: | ^65dB |
Note: All specifications shown are subject to change without notice.
9. Troubleshooting
| Problem | Possible Cause / Solution |
|---|---|
| The radio does not start. | The battery is low, replace with a charged battery or proceed to charge. The battery may not be installed correctly; remove and reattach it. |
| The battery runs down quickly. | The battery life may have ended; replace the battery. Ensure the battery is fully charged and made in full. |
| The receiving indicator LED lights but no sound from the speaker. | Volume setting is too low. Ensure CTCSS or DCS undertones match those programmed in other transceivers in your group. |
| When transmitting, other group members do not receive communication. | Ensure CTCSS or DCS undertones match. You or your partner may be too far apart or in an area with poor RF signal propagation (e.g., tunnels, underground car parks, mountainous areas, large metal structures). |
| In "standby" mode, the transceiver transmits without pressing the "PTT". | Check if the VOX level adjustment function is set too sensitive. |
| Receiving communications from other user groups while communicating with your group. | Change frequency or channel. Change the undertones "CTCSS" or code "DCS" in your group. |
| Communication with other members of your group is poor or low quality. | You or your partner is too far away or in an area of poor radio signal propagation, such as inside a tunnel, underground car park, mountainous area, or near large metal structures. |
If problems persist after these checks, contact your distributor, dealer, or service center.
10. User Tips
- Durability Test: The radio is designed to withstand harsh conditions. It is IP68 waterproof and has been shown to survive being run over by a car in tests.
- Antenna Upgrade: Consider using a 771 Aerial (22cm) for longer distance and better signal traversal compared to standard 17cm antennas.
- Power Management: Utilize the Tri-Power settings (1W, 5W, 10W) to conserve battery life when high power is not needed, and switch to 10W for maximum range.
- Charging Convenience: The Type-C charging port offers modern and universal compatibility for charging.
- Low Light Operation: The built-in high brightness LED flashlight is useful for working in dark environments.
11. Warranty and Support
The device described in this Certificate is guaranteed for a period of TWO YEARS from the date of sale to the final user. This Warranty Certificate is unique and not transferable and may not be reissued for new or original or copy. Substitution of product failure or any part thereof shall not involve extension of the guarantee.
The warranty covers the replacement and free replacement of all parts that are defective in materials and components used in manufacturing and/or assembly of the apparatus.
The warranty does not cover any faults caused by accident, improper installation and use, electric shock (e.g., storms), connection to a power source other than that specified, reverse polarity, or claims due to deterioration in the external appearance from normal use, nor the amount or condition of the accessories.
Checking the accessories is the responsibility of the purchaser at the time of purchasing the device.
The warranty does not cover rechargeable batteries, even if they are part of the equipment purchased, as they are considered consumables. Any impairment must be reported within fifteen days from the date of purchase.
Warranty is valid provided it is complete and properly filled in, legible, and clearly presents the seal and name of the dealer, along with the bill/proof of purchase.
For further support or service, please contact your authorized dealer or service center.