GVDA GD151A GD151B

Contents

GVDA Digital Sound Level Meter User Manual

Models: GD151A, GD151B

1. Introduction

This sound level meter is designed to measure the sound level of various environments, including factories, workshops, schools, residences, offices, and traffic areas. It is also suitable for noise engineering, product quality control, and health prevention. Additionally, it can measure ambient temperature and humidity.

2. Package Contents

Please check the package for the following items:

  • GVDA Digital Sound Level Meter (GD151A or GD151B)
  • User Manual
  • Sponge Ball (Windscreen)
  • Carrying Bag
GVDA GD151A Package Contents
Figure 2.1: Contents of the GD151A package, including the meter, user manual, and carrying bag.

3. Device Overview

The GVDA Digital Sound Level Meter features a clear LCD display and intuitive controls. Below is an overview of the device and its display symbols.

GVDA Digital Sound Level Meter GD151B
Figure 3.1: Front view of the GVDA GD151B Sound Level Meter, showing the display and control buttons.

3.1 Display Symbols

SymbolDescriptionSymbolDescription
نAuto Power OffHData Hold
MAXMaximum ValueMINMinimum Value
°CCelsiusRH%Humidity Unit
°FFahrenheitLow Battery
FASTQuick ResponseSLOWSlow Response
dBDecibel UnitAA Weighted
CC Weighted

3.2 Microphone and Sensors

The device uses a condenser microphone for sound measurement and integrated sensors for temperature and humidity.

Condenser Microphone and Sponge Ball
Figure 3.2: Detail of the condenser microphone and the included sponge ball (windscreen).
Noise Measurement with Humidity, Temperature, Decibel Labels
Figure 3.3: The meter in use, indicating simultaneous measurement of humidity, temperature, and decibel levels.

4. Setup

4.1 Battery Installation

The device requires 3 AAA batteries (not included).

  1. Unscrew the battery cover on the back of the device.
  2. Open the battery compartment.
  3. Insert 3 AAA batteries, ensuring correct polarity (+/-) as indicated inside the compartment.
  4. Close the battery cover and fasten the screws to secure it.

When the low battery symbol appears on the display, replace the batteries promptly.

Battery Compartment with AAA Batteries
Figure 4.1: View of the battery compartment showing the correct placement of 3 AAA batteries.

5. Operation

5.1 General Considerations

  • Wind blowing across the microphone can increase noise measurements. Use the supplied windscreen (sponge ball) when applicable.
  • Calibrate the instrument before each use if possible, especially if it has not been used for a long time.
  • Do not store or operate the instrument in areas of high temperature or humidity.
  • Keep the meter and microphone dry.
  • Avoid severe vibration.
  • Remove batteries if the meter will be stored for long periods.

5.2 Basic Measurement

  1. Open the protection cover of the microphone.
  2. Press the Power button to turn on the meter.
  3. After power-on, the meter will display the sound pressure level reading.
  4. Hold the meter, facing the microphone towards the sound source to be measured.
  5. Read the measured value from the display.
  6. Press the Power button to turn off the power.

5.3 MAX/MIN Function

Press the MAX/MIN button to enable the maximum and minimum value display. Press it again to cycle through MAX and MIN values. Press and hold for about 2 seconds to return to normal measurement mode.

5.4 A/C Weighted Selection (Model B only)

For model GD151B, press and hold the A/C button for about 2 seconds to switch between A and C weighting.

A/C Weighting Comparison GD151A vs GD151B
Figure 5.1: GD151A uses A-weighting for ambient noise, while GD151B offers A/C weighting for mechanical noise.

5.5 Fast/Slow Time Weighted Selection

Press the F/S button to select 'FAST' (125 ms) or 'SLOW' (1 sec) time weighting. 'FAST' or 'SLOW' will appear on the display accordingly. 'FAST' response captures noise peaks and fast-emerging noise. 'SLOW' response monitors consistent sound pressure levels and averages out rapidly changing noise.

Fast/Slow Time Weighted Selection and Data Hold Buttons
Figure 5.2: Buttons for MAX/MIN, Fast/Slow (F/S), and Data Hold (H/*).

5.6 Data Hold

Press the H/* button to enable data retention. Press it again to turn off data hold and return to normal measurement.

5.7 Backlight

Press and hold the H/* button for more than 2 seconds to enable or disable the backlight.

5.8 Automatic Power Off

The meter automatically shuts down after 10 minutes of inactivity to save battery life. The Auto Power Off symbol is displayed when this function is active. To disable it, press and hold the Power button while turning on the device; release the button after power-on. The Auto Power Off symbol will disappear. Restart the instrument to restore the function.

Auto Power Off 10 Minutes
Figure 5.3: The meter features an automatic power-off function after 10 minutes of inactivity.

5.9 Temperature Unit Selection

Press the °C/°F button to switch the temperature unit between Celsius (°C) and Fahrenheit (°F).

6. Maintenance

6.1 Battery Replacement

Refer to Section 4.1 for instructions on battery replacement.

6.2 Cleaning

To avoid damaging the case, do not use corrosive agents or solvents. Wipe the shell regularly with a mild detergent or a damp cloth.

7. Troubleshooting

  • Device does not power on: Check battery installation and ensure batteries are fresh.
  • Erratic readings: Ensure the microphone is clear of obstructions and the windscreen (sponge ball) is properly installed. Avoid strong winds or vibrations during measurement.
  • Display issues: If the display is dim or incomplete, replace the batteries.

8. Specifications

ParameterSpecification
Measurement Range30~130dB (GD151A: 30-130dBA; GD151B: 30-130dBA or 30-130dBC)
Frequency Range30Hz-8KHz
Dynamic Range50dB
Sound Accuracy±1.5dB (94dB@1KHz); ±5dB (94dB@8KHz)
Frequency WeightingGD151A: A weighting; GD151B: A weighting, C weighting
Time WeightingFast: 125ms; Slow: 1sec
Temperature Range-20°C-60°C (-4°F-140°F)
Temperature Accuracy0°C-45°C (32°F-113°F): ±1°C/2°F; Other: ±1.5°C/3°F
Humidity Range0.0%-99.9%RH
Humidity Accuracy20%-80%: ±5RH; Other: ±6RH
Auto Power Off10 minutes
Power Supply3 x AAA batteries (not included)
Item Size142 x 58 x 26mm
Microphone TypeElectret condenser
Operating Conditions0~50°C, <80%RH, altitude <2000m
Storage Conditions-10~50°C

9. User Tips

  • This meter is excellent for comparing sound levels from different sources, such as speakers, by utilizing both A and C weighting curves (on GD151B).
  • Always ensure fresh batteries are installed for accurate and consistent measurements.
  • Use the sponge ball (windscreen) to minimize wind noise, especially when measuring outdoors.

10. Frequently Asked Questions (FAQ)

Q: What brand is this sound level meter?
A: The brand is GVDA.
Q: Can this device notify me when a certain noise level is reached?
A: No, this device is designed for measurement and display of sound levels, temperature, and humidity. It does not have an alarm or notification function for specific thresholds.
Q: The display only shows up to 99.9 dB, but the description states 130 dB. Is there a switch?
A: The device is specified to measure up to 130 dB. If your display appears to be limited to 99.9 dB, please ensure you are operating it correctly. The display may auto-range, or there might be specific conditions for displaying higher values. Refer to the full user manual for any advanced display modes or range settings.

11. Warranty and Support

For warranty information, technical support, or service inquiries, please refer to the official GVDA website or contact your authorized retailer.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.