E-ACE K01/K02

Contents

E-ACE Solar Power TPMS Car Tire Pressure Alarm Monitor System

Model: K01/K02

Brand: E-ACE

1. Introduction

Thank you for purchasing the E-ACE Tire Pressure Monitoring System (TPMS). This system is designed to provide enhanced protection while driving by continuously monitoring tire conditions. After installation, the TPMS system monitors tire pressure and temperature in real-time. Should any abnormal tire pressure or temperature be detected, the system will issue an audible warning and display a bright flashing icon to alert the driver. This real-time feedback helps prevent traffic accidents and ensures the safety of drivers and passengers.

Important Reminder:

Please read this instruction manual carefully before use. It is not recommended to change the machine parameters unless absolutely necessary for specific purposes. The schematic diagrams in this manual are for reference only; please refer to the actual product for precise details. Before installation, ensure the host's power is turned on.

Video: E-ACE TPMS product unboxing and demonstration of features like low pressure warning.

2. Specifications

Product Specifications
FeatureSpecification
Brand NameE-ACE
Model NameK01/K02
Item TypeAlarm Systems & Security
MaterialPlastic
Voltage5V
Special FeaturesSolar Energy
Is Batteries IncludedYes
Item Weight0.4 kg
Item Height26 mm
Item Width81 mm
Item Length75 mm
External Testing CertificationCE
CertificationRoHS, FCC, ECE, CE, CCC, CC
OriginMainland China
Package Length14 cm
Package Width11 cm
Package Height5 cm
Package Weight0.187 kg
Product dimensions and display features

Diagram showing the dimensions of the TPMS monitor (Length: 75mm, Width: 81mm, Height: 26mm) and key display elements like Solar Charging Prompting, Tire Pressure Display, Battery Status, Tire Temperature Display, USB Charging Interface, and control buttons (Select, Menu).

3. Components

The E-ACE TPMS system typically includes the following components:

  • TPMS Monitor (with solar panel and USB charging port)
  • External Sensors (K01 model) or Built-in Sensors (K02 model)
  • USB Charging Cable
  • Anti-theft Nuts (for external sensors)
  • Wrench (for external sensors)
  • Backup Batteries (for external sensors)
  • Adhesive Pad (for monitor mounting)
  • User Manual
Main product image showing monitor and external sensors

The E-ACE TPMS monitor with external sensors, showing the solar panel, display, and individual sensors with their respective tire positions (F.L, F.R, R.L, R.R).

K01-External Sensor type image

Image showing the K01-External Sensors, which are valve cap style sensors.

K02-Built-in Sensor type image

Image showing the K02-Built-in Sensors, which are installed inside the tire.

4. Setup Instructions

4.1 Monitor Installation

Place the monitor on a suitable position on the left side of the center console using the provided adhesive pad. The product does not require manual turning on or off.

4.2 External Sensor Installation (K01 Model)

Before installing external sensors, ensure the host is powered on.

  1. Screw the anti-theft nut onto the valve stem first.
  2. Install the sensor onto the valve according to its designated position (e.g., FL for Front Left, FR for Front Right, RL for Rear Left, RR for Rear Right) and tighten it.
  3. Screw the anti-theft nut counter-clockwise against the sensor.
  4. Use the provided wrench to tighten both the sensor and the anti-theft nut securely.

If no pressure is displayed for a corresponding position on the host, reinstall the sensor for that position.

Step 1: Screw in the anti-theft nut first

Step 1: Screw in the anti-theft nut first.

Step 2: Tighten the sensor

Step 2: Tighten the sensor onto the valve stem.

Step 3: Screw the anti-theft nut counterclockwise against the sensor

Step 3: Screw the anti-theft nut counterclockwise against the sensor.

Step 4: Tighten the sensor and anti-theft nut with a wrench

Step 4: Use the wrench to tighten both the sensor and the anti-theft nut.

4.3 Built-in Sensor Installation (K02 Model)

Before installing built-in sensors, ensure the main unit's power is turned on by long-pressing the left button. Install the sensors into the tires according to their designated positions. Replace the original car valve and inflate the tires sequentially after installation. The main unit must be powered on when the air is filled.

5. Operating Instructions

5.1 Interface and Display Description

Diagram of the TPMS monitor display and buttons

Diagram illustrating the TPMS monitor's display and button layout. Key elements include: 1. Power/Left button, 2. SET button, 3. Right button, 4. Solar energy, 5. Solar icon, 6. Tire pressure units, 7. Tyre temperature, 8. Tire Pressure, 9. Temperature unit, 10. Battery, 11. Clock.

5.2 Button Function Description

  • USB Port: Used for charging the receiver.
  • Power/Left Button: Short press to adjust brightness in standby mode, long press to turn on/off the device. Also used to switch left in menus.
  • Right Button: Short press to adjust brightness in standby mode, long press to turn off alarms. Also used to switch right in menus.
  • SET Button (M Menu Button/Confirm Button): Long press in standby mode to enter menu mode. Short press to confirm selected parameters.

5.3 Basic Functions

  • The factory default tire pressure unit is BAR, temperature unit is °C. The upper limit for tire pressure is 3.2 bar, the lower limit is 1.8 bar, and the temperature alarm value is 68°C.
  • Backlight brightness automatically adjusts based on light intensity. It can also be manually adjusted using the left and right buttons.

6. Advanced Settings

These settings are for advanced users. It is not recommended to change them unless necessary. If no operation occurs within 30 seconds in menu mode, the system will automatically exit to the main interface, and unsaved settings will be lost. Always long-press the 'Menu' button to return to the main interface after completing any setting.

6.1 Unit Setting (Factory default: Bar, °C)

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system setting state. The 'Bar' icon will appear in the lower left corner.
  2. Press the 'Menu' button again to enter the operable setting state.
  3. Use the 'Left' and 'Right' buttons to select between 'Psi' or 'Bar' units.
  4. Once the desired unit is selected, press the 'Menu' button to complete the setting.
  5. To set the temperature unit, long press the 'Menu' button for 3 seconds, then press the 'Right' button once.
  6. Press the 'Menu' button to enter the operable setting state.
  7. Use the 'Left' and 'Right' buttons to select between '°C' or '°F' units.
  8. Once the desired unit is selected, press the 'Menu' button to complete the setting.
Display showing BAR and PSI unit settings

The display showing options for pressure units (Bar, Psi) and temperature units (°C, °F).

6.2 Time Setting (For models with clock function only)

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system setting state.
  2. Press the 'Right' button twice to enter the time setting.
  3. Short press the 'Menu' button twice; the hour number will flash.
  4. Use the 'Left' and 'Right' buttons to adjust the hour.
  5. After setting the hour, short press the 'Menu' button to set the minutes.
  6. Adjust the minutes with the 'Left' and 'Right' buttons.
  7. Long press the 'Menu' button to exit the setting once the time is complete.
Display showing time setting

The display showing the time setting interface, with hours and minutes adjustable.

6.3 Changing Tire Pressure Limits

To change the upper limit:

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system setting state.
  2. Press the 'Right' button twice to enter the maximum air pressure setting.
  3. Press the 'Menu' button once; the air pressure number will flash.
  4. Use the 'Left' and 'Right' buttons to set the desired maximum air pressure.
  5. Long press the 'Menu' button to exit.

To change the lower limit:

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system setting state.
  2. Press the 'Right' button three times to enter the lower air pressure setting.
  3. Press the 'Menu' button once; the air pressure number will flash.
  4. Use the 'Left' and 'Right' buttons to set the desired lower air pressure.
  5. Long press the 'Menu' button to exit.
Display showing upper and lower pressure limits

The display showing the upper (PH) and lower (PL) tire pressure limit settings in Bar.

6.4 Changing Temperature Limits

  1. In standby mode, long press the 'Menu' button for 3 seconds to enter system setting state.
  2. Press the 'Right' button four times to enter the tire temperature upper limit setting.
  3. Short press the 'Menu' button once; the tire temperature number will flash.
  4. Use the 'Left' and 'Right' buttons to set the desired highest upper limit tire temperature.
  5. Long press the 'Menu' button to exit after the setting is complete.
Display showing temperature limit

The display showing the temperature limit setting (EX) in °C.

6.5 Single Sensor Replacement

To replace a sensor:

  1. Remove the old sensor and install the new sensor (built-in or external) in its place.
  2. In standby mode, long press the 'Menu' button for 3 seconds to enter system setting state.
  3. Press the 'Right' button five times to enter the pairing selection mode.
  4. Press the 'Menu' button once. The '0' on the interface will flash, defaulting to the front left wheel.
  5. Use the 'Left' and 'Right' buttons to select the position of the sensor to be replaced (0=Front Left, 1=Front Right, 2=Rear Left, 3=Rear Right).
  6. After selecting the position, press the 'Menu' button. The number will flash.
  7. Install the new sensor on the tire and check if the number changes on the display.
  8. Once the number changes, long press the 'Menu' button to exit.

Note:

  • If it's a built-in sensor, inflate and deflate the tire when the number below flashes.
  • During this pairing process, any sensor can be matched to any position.
Display showing sensor pairing mode

The display showing the sensor pairing mode, indicating which tire position is being configured.

6.6 Restore Factory Settings (Re-pairing)

  1. While powered on, press and hold the 'Menu' button for 3 seconds to enter settings.
  2. Press the 'Left' button to navigate to item 7.
  3. Press the 'Menu' button twice to reset the device and restore factory settings. The system will then search for sensors again.
  4. To update sensors, install new sensors on the valves in order, or drive the car at a speed of 30 km/h or more after resetting.
  5. After driving for approximately 10-30 minutes, the host will automatically search for sensor signals. Once all 4 sensors are found, pairing is complete.

After restoring factory settings, any previously manually set data will revert to factory defaults.

Display showing factory reset confirmation

The display showing the factory reset confirmation screen.

7. Maintenance

7.1 Replacing Sensor Batteries (External Sensors)

When replacing sensor batteries, disassemble and install components one by one. Do not mix or disassemble and install multiple parts simultaneously. The external sensors use CR1632 button batteries, with a working temperature range of -30°C to 80°C.

  1. Before disassembling, prepare a nut wrench. Turn the anti-theft nut clockwise to separate it from the sensor, then remove the sensor counter-clockwise.
  2. Use the wrench to unscrew the upper cover of the sensor in a counter-clockwise direction.
  3. Remove the old battery from the battery holder. Dispose of it responsibly according to environmental protection guidelines.
  4. Note the positive and negative positions (positive '+' facing upwards). Install a new CR1632 lithium battery.
  5. Screw on the upper cover of the sensor, then use the wrench to tighten it clockwise.
Sensor battery replacement steps

Images illustrating the steps to replace the battery in an external sensor: a) Opening the outer cover with a wrench, b) Removing the old battery and inserting a new one, c) Closing the upper cover and tightening with a wrench.

8. Troubleshooting

Common Issues and Solutions
ProblemPossible Cause / Solution
Sensor not working / stopped workingBattery drained or faulty sensor. Try replacing the sensor battery (for external sensors) or re-pairing the sensor. If the issue persists, the sensor may need replacement.
Inaccurate pressure readings (e.g., 99, 2-3 PSI difference)Sensors may not be properly calibrated or paired. Ensure correct installation and re-pair if necessary. Note that slight variations (approx. 0.1 bar or 2-3 PSI) compared to professional gauges are possible.
Inaccurate temperature readingsTemperature readings may have slight variations. Ensure sensors are correctly installed.
Display issues (screen turns off, buttons damaged)Check power supply and connections. If buttons are physically damaged, the unit may require repair or replacement. Screen turning off might be due to power saving mode or low battery.
Solar panel not chargingEnsure the solar panel is exposed to direct sunlight. If the device is configured to turn off after a period of inactivity, it might not charge. Check settings.
Continuous beeping with a clock iconThis typically indicates an alarm condition related to time settings or a system alert. Refer to the time setting section (6.2) to ensure the clock is set correctly. If the alarm persists, check other alarm settings (pressure/temperature limits).
Difficulty pairing sensorsEnsure the host is in pairing mode and follow the single sensor replacement or factory reset procedures carefully. Make sure to install sensors in the correct order or adjust tire pressures to differentiate them during pairing.

9. User Tips

  • Easy Installation: Many users find the system easy to install, with some reporting full functionality within minutes. The external sensors are particularly quick to set up.
  • Shake Awake Feature: The monitor often includes a 'shake awake' feature, meaning it turns on automatically when motion is detected, eliminating the need to manually power it on.
  • Real-time Monitoring: This system provides real-time pressure and temperature readings, which is a significant advantage over standard TPMS systems that only alert to issues.
  • Solar Charging Convenience: The solar panel effectively keeps the monitor charged, reducing reliance on the USB cable.
  • Setting Alarms: Take advantage of the customizable alarm limits for both pressure and temperature to receive timely warnings.
  • External Sensor Installation Tip: For external sensors, ensure you screw on the anti-theft nut first, then the sensor, and finally tighten the nut against the sensor with the provided wrench for a secure fit.
  • Pairing Tip: If you encounter difficulty pairing, try adjusting the tire pressures to different values for each tire. This can help the system distinguish and pair each sensor correctly.
  • Visibility in Sunlight: In very bright sunlight, the display might be harder to read. Some users suggest creating a small shade for the monitor to improve visibility.
  • Battery Life: The sensor batteries generally last a good period (e.g., 2 years for external sensors). The product often includes spare batteries.
  • Compatibility: The system is suitable for a wide range of vehicles, including cars, SUVs, ORVs, MPVs, Minibuses, and Wagons. It can also be useful for older cars or trailers.

10. Warranty and Support

For detailed warranty information and further support, please refer to the official user manual PDF. You can access the PDF manual for this product here.

For any inquiries or technical assistance, please contact E-ACE support:

  • Website: www.e-ace.cn
  • Email: fireking@e-ace.cn
  • Phone: +86 0755-8464 4084
  • WhatsApp: +86-18127083357
  • Address: Floor 2nd, No.1 Yuanxia street, Pingshan District, Shenzhen City, Guangdong Province, 518000, China

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.