Introduction
The YIHUA 938D Portable Tweezers Soldering Station is designed for precise soldering and desoldering of Surface Mount Device (SMD) electronic components. Its parallel tweezers design allows for efficient handling of small components, making it an ideal tool for electronics repair and assembly. This manual provides essential information for the safe and effective use of your soldering station.
Safety Precautions
- Always ensure the power supply matches the specified voltage (110V-240V optional).
- Use in a well-ventilated area to avoid inhaling solder fumes.
- The soldering tips and tweezers become extremely hot. Avoid direct contact with skin to prevent burns.
- Always place the tweezers in the designated stand when not in use.
- Keep out of reach of children.
- Do not operate the device if the power cord or any part of the unit is damaged.
Package Contents
Verify that all items are present in your package:
- YIHUA 938D Control Unit
- Tweezers Soldering Iron
- Soldering Iron Stand with Cleaning Sponge
- Power Plug (US, EU, UK, or AU type, depending on region)
- User Manual (this document)

Setup Instructions
- Connect the Tweezers: Insert the connector of the tweezers soldering iron into the corresponding port on the YIHUA 938D control unit. Ensure it is securely fastened.
- Place in Stand: Position the tweezers soldering iron in its dedicated stand. The stand includes a sponge for tip cleaning.
- Connect Power: Plug the appropriate power cord into the control unit and then into a suitable electrical outlet. The unit supports 110V-240V.

Operating Instructions
Power On/Off
- To power on the unit, flip the 'ON/OFF' switch located on the control unit to the 'ON' position. The digital display will illuminate.
- To power off, flip the switch to the 'OFF' position.
Temperature Adjustment
- The YIHUA 938D features a digital temperature display and a rotary knob for precise temperature control.
- Rotate the knob to increase or decrease the desired temperature. The temperature range is 200-480°C (392-896°F).
- Use the °C/°F switch to toggle between Celsius and Fahrenheit temperature readings.


SMD Desoldering and Soldering
- The parallel tweezers design is ideal for simultaneously heating both ends of SMD components for easy removal or precise placement.
- Apply the heated tips to the component leads, allow the solder to melt, and then gently lift or place the component.


Sleep Function
- The unit features an automatic sleep function. If there is no operation for 10 minutes, the soldering iron will enter sleep mode.
- This function helps save energy and prolong the lifespan of the iron tips.

Product Demonstration Video
Maintenance
- Tip Cleaning: Regularly clean the soldering tips using the wet sponge provided in the stand. This helps maintain optimal heat transfer and prevents oxidation.
- Tip Tinning: After cleaning, re-tin the tips with a small amount of solder to protect them from oxidation and ensure readiness for the next use.
- Storage: Always store the tweezers soldering iron in its stand when not in use.
- General Cleaning: Keep the control unit and tweezers free from dust and debris. Use a soft, dry cloth for cleaning.
Troubleshooting
| Problem | Possible Cause | Solution |
|---|---|---|
| Unit does not power on. | No power supply; loose power connection; faulty power switch. | Check power outlet and connections. Ensure power switch is ON. If problem persists, contact support. |
| Tips not heating up. | Loose connection between tweezers and control unit; faulty heating element; unit in sleep mode. | Ensure tweezers are securely connected. Check if the unit is in sleep mode (move the tweezers to wake it up). If heating core is broken, replacement may be needed. |
| Inaccurate temperature reading. | Sensor issue; incorrect calibration. | Ensure tips are clean. If problem persists, contact support for calibration or repair. |
| Tips are uneven or break easily. | Manufacturing defect; improper handling; wear and tear. | Handle tips gently. If tips are defective, consider purchasing replacement tips. |
| Handle gets hot during use. | Normal operation for high temperatures; extended use. | This can be normal. Ensure proper grip and take breaks if uncomfortable. |
Specifications
| Feature | Specification |
|---|---|
| Brand Name | YIHUA |
| Model Number | YIHUA 938D tweezers Soldering Iron Station |
| Input Voltage | 110V~240V optional |
| Output Temperature | 200~480°C (392~896°F) |
| Temperature Stability | 2 (static state) |
| Output Power | 120W Soldering Iron Station |
| Dimensions | 37 x 17.5 x 8 cm |
| Weight | 0.803 kg |
| Certification | CE, FCC |
| Smart Device | No |
| Origin | Mainland China |
User Tips
- This tool is highly effective for SMD work due to its quick heating and stable temperature, making it easier to work in small spaces.
- For complex circuit boards or very small SMD components, consider using a PCB preheater in conjunction with the tweezers for optimal results.
- While the unit is generally well-made, some users have noted that the tips might be uneven or prone to breakage. Inspect tips regularly and have replacements on hand if needed.
- The handle may become warm during prolonged use. Ensure a comfortable grip and take short breaks if necessary.
- Always double-check the plug type when ordering to ensure compatibility with your region's electrical outlets.
Warranty and Support
For detailed warranty information, technical support, or to purchase replacement parts, please refer to the official YIHUA website or contact your retailer. A comprehensive user manual in PDF format is also available for download: