diymore RH-D08

Contents

diymore RH-D08 5.8GHz Microwave Radar Sensor Light Switch User Manual

Model: RH-D08

1. Introduction

The diymore RH-D08 is a 5.8GHz microwave radar sensor light switch designed for automatic lighting control based on human motion. It offers high sensitivity, 360° sensing without blind spots, and multiple adjustable settings for light sensitivity, delay time, and detection distance. This manual provides detailed instructions for installation, operation, and maintenance to ensure optimal performance and safety.

diymore RH-D08 Microwave Sensor

Figure 1: diymore RH-D08 Microwave Radar Sensor Light Switch

2. Product Features

  • 360° sensing without blind spot
  • Multiple adjustment settings (light sensitivity, delay time, detection distance)
  • Fire-retardant material for safety
  • High sensitivity 5.8GHz microwave radar induction
  • Press-type terminal installation for convenience

3. Setup and Installation

3.1 Safety Precautions

  • Ensure power is OFF before installation to prevent electric shock.
  • Installation should be performed by a qualified electrician if you are unsure.
  • Do not exceed the maximum rated load of 200W for LED lights.

3.2 Wiring Diagram

Connect the sensor according to the diagram below. Ensure correct polarity for Live (L) and Neutral (N) inputs, and connect the load (light fixture) to the switched Live (L') and Neutral (N).

Wiring Diagram for RH-D08 Sensor

Figure 2: Wiring Diagram

  • L: Live Input (AC 100-240V)
  • N: Neutral Input (AC 100-240V)
  • L': Switched Live Output to Load
  • N': Neutral Output to Load

3.3 Mounting

The sensor supports top-mounted and side-mounted installations, suitable for various scenarios. The recommended installation height is 2.5 to 3.5 meters.

Ceiling and Side Mount Installation Considerations

Figure 3: Installation Considerations

  • Ceiling Installation: Ceilings generally do not penetrate the microwave signal. Thin boards may be penetrated.
  • Side Mount: Thin walls (e.g., gypsum) can be penetrated. Be aware that motion from adjacent areas (e.g., next door) might trigger the light. If installing multiple sensors, ensure sufficient distance to avoid mutual interference. The sensing distance can be reduced to minimize unintended triggers.

3.4 Initial Configuration (DIP Switches)

The sensor features six DIP switches (1-6) for adjusting its operational parameters. Use a small tool to dial the switches up (ON) or down (OFF) according to your requirements.

DIP Switch Adjustment Settings

Figure 4: Multiple Adjustment Settings

DIP Switch Settings
SettingSwitchesOption 'a' (ON-ON)Option 'b' (ON-OFF)Option 'c' (OFF-ON)Option 'd' (OFF-OFF)
Light Sensitivity1 & 210 LUX30 LUX50 LUXDay (always on if motion)
Delay Time3 & 412 Minutes8 Minutes3 Minutes8 Seconds
Detection Distance5 & 6100%75%50%20%

4. Operating Instructions

Once installed and configured, the sensor operates automatically:

  1. When motion is detected within the configured range and the ambient light level is below the set threshold (if not set to 'Day'), the connected light will turn on.
  2. The light will remain on as long as continuous motion is detected within the sensing area.
  3. After motion ceases, the sensor will start a countdown based on the set delay time.
  4. Once the delay time expires, the light will automatically turn off.

The green LED indicator on the sensor typically illuminates when motion is detected or when the sensor is active.

Scenario Shows for Sensor Application

Figure 5: Typical Application Scenarios

5. Maintenance

  • Keep the sensor clean and free from dust to ensure optimal performance. Use a soft, dry cloth for cleaning.
  • Do not use abrasive cleaners or solvents, as they may damage the sensor's housing.
  • Ensure the sensor's detection area is not obstructed by furniture or other objects.

6. Troubleshooting

  • Light does not turn on:
    • Check power supply and wiring connections.
    • Verify the light sensitivity setting (DIP switches 1 & 2) is appropriate for ambient light conditions.
    • Ensure motion is within the detection range and distance setting (DIP switches 5 & 6).
  • Light stays on continuously:
    • Check the delay time setting (DIP switches 3 & 4).
    • Ensure there is no constant motion within the detection area.
    • Verify the light sensitivity is not set to 'Day' if you require light-dependent operation.
  • Light turns on unexpectedly:
    • Adjust the detection distance (DIP switches 5 & 6) to a lower percentage.
    • Review side-mount installation considerations to minimize interference from adjacent areas.

7. Specifications

ParameterValue
Product Name5.8G Radar Sensor
ModelRH-D08
Product ColorWhite
Working VoltageAC 220-240V
Detection Angle360°
Working Temperature-10°C to +40°C
Detection Distance8m radius (Max)
Operating Frequency50/60Hz (5.8GHz ISM band)
Ambient Light<50 LUX (adjustable)
Delay Time8 seconds - 12 minutes (adjustable)
Installation Height2.5 - 3.5 M
Rated Load200W LED light
MaterialFlame Retardant PC
Inspection Movement Speed0.6 - 1.5 M/s
Waterproof LevelIP42
Radiation Power<10mW
Standby Power Consumption0.5W (static 0.1W)
Working Humidity≤93%RH
Dimensions (L x W x H)70mm x 36mm x 25mm
Net Weight54g
Product Dimensions

Figure 6: Product Dimensions

8. User Tips

  • For best results, ensure the sensor is properly connected to your ceiling light fixture.
  • Take time to experiment with the DIP switch settings for light sensitivity, delay time, and detection distance to find the optimal configuration for your specific environment.
  • Consider the penetration capabilities of microwave sensors when choosing an installation location to avoid unintended triggers from adjacent rooms or outside areas.

9. Warranty and Support

For warranty information, please refer to the terms provided by your retailer or contact the seller directly. For technical support or further inquiries, please reach out to the diymore customer service.

A detailed user manual in PDF format may also be available for download from the seller's product page: View PDF Manual

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.