Lifud LF-GIF Series

Contents

Lifud Flicker-Free LED Driver User Manual

Models: LF-GIF022, LF-GIF030, LF-GIF040 Series

1. Introduction

This manual provides essential information for the safe and efficient use of your Lifud Flicker-Free LED Driver. This power supply is an exclusively designed stabilized LED driver for LED lamps, utilizing constant current technology. It is suitable for various constant current LED lighting applications, particularly for panel lights.

Lifud Flicker-Free LED Driver for Indoor Lighting
Lifud Flicker-Free LED Driver, designed for indoor lighting applications.

2. Important Safety Information

WARNING: This unit uses dangerous mains voltage (100-240VAC). Installation must only be performed by qualified electricians in accordance with European safety standards and relevant national regulations. Failure to follow these instructions may result in fire, electric shock, or other hazards.

  • Ensure all LEDs are completely wired and connected before switching on the supply voltage.
  • This LED driver is designed exclusively for LED lamps.
  • Pay close attention to the polarity of the LED connections. Incorrect polarity will damage the LED.
  • The LED driver is intended for indoor use only.
  • Permissible operating temperature range is -20°C to 40°C.
  • The LED driver can be installed independently when equipped with a terminal cover and cable clamp.
  • Do not exceed the indicated load for the driver.
  • The maximum length of the output cable to the LED lamps should not exceed 2 meters to comply with EMC standards.
  • The manufacturer is not responsible for damages resulting from improper use or incorrect connection.
  • When connecting to LEDs, carefully observe the correct positive (+) and negative (-) terminals on the LED driver.
  • This LED Driver cannot be regulated via a phase leading edge or trailing edge dimmer.

3. Product Features

  • Flicker-Free Operation: Provides stable lighting output without visible flicker.
  • High Power Factor (PFC): Built-in active PFC function ensures high power efficiency and low Total Harmonic Distortion (THD).
  • Quick Start-up: Fast turn-on time, typically less than 0.5 seconds at 230Vac.
  • Simplified Installation: Features a screw-free design and does not require holding lead wires, simplifying the wiring process.
  • High Quality SELV LED Driver: Ensures safety and reliable performance.
  • Certifications: Complies with TUV-CE, CB, SAA, RCM, and ENEC standards.
  • Durable Construction: Made from PC material.
Lifud LED Driver with built-in terminals
The Lifud LED Driver features built-in terminals for easy, screw-free wiring.

4. Specifications

Attribute Value
Item TypeLighting Transformers
Model NumberLF-GIF (LF-GIF022, LF-GIF030, LF-GIF040 series)
Input Voltage Range200-240V AC
Nominal Voltage240V+
Output Voltage33-40V DC (for LF-GIF030/040), 25-40V DC (for LF-GIF022)
Input SignalAC
Output SignalDC
Power Factor (PF)<0.9 (typically PF:0.9C)
Efficiency86%
Output CurrentVaries by model (e.g., 250mA, 400mA, 600mA, 700mA, 800mA, 900mA, 1000mA)
Current Tolerance±5%
Power Tolerance4%
Driver TypeConstant current
Wiring ConnectionTerminal block
ProtectionOver heat / Short circuit
Start-up Time<0.5S@230Vac
Total Harmonic Distortion (THD)≤20%@230Vac
Standby Power Consumption≤0.5W
IP RatingIP20
Working Temperature-30°C to 45°C
Hi-Pot TestI/P-O/P: 3750VAC
MaterialPC
Weight70g
Dimensions (approx.)L115 x W41 x H28mm (See diagrams for specific models)
OriginMainland China

4.1. Model-Specific Output and Dimensions

The LF-GIF series includes various models with different output currents and power ratings. All models generally share the same physical dimensions (L115 x W41 x H28mm).

  • LF-GIF022YA0400H LED Driver specifications
    Model LF-GIF022YA0400H: Rated 16W, Output 400mA / 25-40V. Dimensions: L115 x W41 x H28mm.
  • LF-GIF030YS0600H LED Driver specifications
    Model LF-GIF030YS0600H: Rated 24W, Output 600mA / 33-40V. Dimensions: L115 x W41 x H28mm.
  • LF-GIF030YS0700H LED Driver specifications
    Model LF-GIF030YS0700H: Rated 28W, Output 700mA / 33-40V. Dimensions: L115 x W41 x H28mm.
  • LF-GIF040YS0800H LED Driver specifications
    Model LF-GIF040YS0800H: Rated 32W, Output 800mA / 33-40V. Dimensions: L115 x W41 x H28mm.
  • LF-GIF040YS1000H LED Driver specifications
    Model LF-GIF040YS1000H: Rated 40W, Output 1000mA / 33-40V. Dimensions: L115 x W41 x H28mm.

4.2. Performance Curves

The following diagrams illustrate the Power Factor (PF) and Lifetime curves for various models in the LF-GIF series, based on specific operating conditions.

  • PF Curves for LF-GIF030YS LED Driver
    Power Factor (PF) Curves for LF-GIF030YS models (33-40Vdc, 550mA-750mA).
  • Lifetime Curve for LF-GIF022YAxxxxH LED Driver
    Lifetime Curve for LF-GIF022YAxxxxH models (25-40Vdc, 400mA-500mA), illustrating lifetime data based on casing temperature.
  • Lifetime Curve for LF-GIF030YS LED Driver
    Lifetime Curve for LF-GIF030YS models (33-40Vdc, 550mA-750mA), showing expected life above 43.8K hours at Tc=84.2°C.
  • PF Curves for LF-GIF040YS LED Driver
    Power Factor (PF) Curves for LF-GIF040YS models (33-40Vdc, 800mA-1050mA).
  • Lifetime Curve for LF-GIF040YS LED Driver
    Lifetime Curve for LF-GIF040YS models (33-40Vdc, 800mA-1050mA), showing expected life above 43.8K hours at Tc=89.0°C.

4.3. Compliance and Certifications

The Lifud LED Driver complies with various international safety and electromagnetic compatibility standards:

Safety Standards:

  • ENEC: EN61347-1: 2015, EN 61347-2-13: 2014/A1: 2017, EN 62384: 2016/A1: 2009
  • CE-LVD: EN 61347-2-13: 2014/A1: 2017, EN 61347-1: 2015, EN 62493: 2015
  • CB: IEC 61347-1: 2015, IEC61347-2-3: 2014, IEC 61347-2-13: 2014/AMD1: 2016
  • SAA: AS 61347.2-13: 2018
  • CCC: GB19510.1-2009, GB19510.14-2009

Electromagnetic Interference (EMI):

  • CE-EMC/RCM: EN55015, EN61000-3-2, EN61000-3-3
  • CCC: GB/T17743, GB17625.1, GB17625.2

Electromagnetic Susceptibility (EMS):

  • CE-EMC/RCM: EN61000-4-2, 3, 4, 5 (lightning strike 1kV), 6, 11
  • CCC: GB/T17626.2, 3, 4, 5 (lightning strike 1kV), 6, 11

5. Installation and Setup

Installation should only be carried out by qualified personnel. Refer to the safety information section before proceeding.

  1. Wiring Preparation: Ensure the main power supply is OFF before starting any wiring.
  2. Connect Input: Connect the AC input wires (200-240VAC) to the designated AC-L and AC-N terminals on the driver.
  3. Connect Output: Connect the LED lamp's positive (+) and negative (-) wires to the corresponding LED+ and LED- output terminals on the driver. Observe correct polarity to prevent damage.
  4. Secure Connections: The driver features a terminal block for screw-free wiring. Ensure all connections are firm and secure.
  5. Independent Installation: The LED driver can be installed independently if it has a terminal cover and cable clamp.
  6. Cable Length: Ensure the output cable length to the LED lamps does not exceed 2 meters to meet EMC standards.
  7. Power On: Once all connections are verified and secure, restore power to the unit.
Lifud LED Driver wiring diagram
Detailed view of the Lifud LED Driver showing input (AC-L, AC-N) and output (LED+, LED-) terminals. Note the 7.5mm strip length for wires.
Wiring connection diagram for Lifud LED Driver
General wiring connection diagram for the LED driver, illustrating input and output connections.

6. Operation

Once correctly installed and powered, the Lifud LED Driver will provide a stable, flicker-free constant current output to your LED lamps. The driver is designed for fast turn-on, typically activating the LEDs in less than 0.5 seconds.

The driver operates within the specified input voltage range of 200-240V AC and delivers a constant DC output current tailored to the specific model (e.g., 250mA, 400mA, 600mA, 700mA, 800mA, 900mA, 1000mA) and voltage (25-40V DC or 33-40V DC).

Note: This LED driver is not compatible with phase leading edge or trailing edge dimmers.

7. Maintenance

The Lifud LED Driver is designed for long-term, reliable operation with minimal maintenance. However, proper environmental conditions are crucial for its longevity.

  • Temperature Management: Operation in excessively high ambient temperatures or through external heating will reduce the service life of the driver. During installation, especially within luminaires, ensure adequate heat dissipation (heat transfer) measures are in place. The ambient temperature and/or the tc-point temperature must not be exceeded at any time.
  • Cleaning: Keep the driver free from dust and debris to ensure proper heat dissipation. Use a dry, soft cloth for cleaning. Do not use liquid cleaners.
  • Inspection: Periodically inspect the wiring for any signs of damage or loose connections.

The manufacturer is not liable for damage resulting from improper use or failure to adhere to temperature guidelines.

8. Troubleshooting

If you encounter issues with your LED driver, consider the following common problems and solutions:

  • No Light Output:
    • Check if the main power supply is active.
    • Verify all input (AC) and output (LED) connections are secure and correctly wired according to polarity.
    • Ensure the LED lamps are functional.
    • Confirm the load connected to the driver does not exceed its indicated capacity.
  • LEDs Flickering or Dim:
    • Ensure the input voltage is within the specified 200-240V AC range.
    • Check for loose connections.
    • Confirm that no incompatible dimmer (phase leading edge or trailing edge) is connected to the circuit.
  • Driver Overheating:
    • Ensure adequate ventilation and heat dissipation around the driver, especially if installed within a luminaire.
    • Verify the ambient temperature is within the -20°C to 40°C operating range.
    • Confirm the load is not exceeding the driver's rated capacity.
  • LED Damage:
    • Incorrect LED polarity during connection is a common cause of damage. Always double-check polarity (+ to + and - to -).

If the problem persists after checking these points, consult a qualified electrician or contact customer support.

9. User Tips

Based on general user experiences with LED drivers:

  • Always plan your wiring layout before installation to ensure proper cable lengths and accessibility.
  • For multiple LED panels, ensure each driver is matched to the correct load and current requirements of its respective panel.
  • Consider using wire connectors that provide a secure and insulated connection for long-term reliability.

(No specific user reviews or Q&A were provided for this product to generate more detailed tips.)

10. Warranty and Support

The Lifud Flicker-Free LED Driver comes with a 5-year warranty from the date of purchase, covering defects in materials and workmanship under normal use.

For detailed product information, technical specifications, or troubleshooting assistance, you may refer to the official user manual PDF available from the seller. A digital copy of the user manual can be found at: Lifud LED Driver User Manual (PDF).

For further support, please contact your retailer or the manufacturer directly.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.