1. Introduction
Thank you for choosing the FENVI 300Mbps Wireless WiFi Repeater. This device is designed to extend the coverage of your existing wireless network, eliminate Wi-Fi dead zones, and provide a stronger, more reliable signal throughout your home or office. It supports both Repeater and Access Point (AP) modes to suit various networking needs.

Figure 1: FENVI WiFi Repeater front view highlighting features like Long Range, Super Signal, Easy Operation, Universal Booster, WiFi, 2.4G, N300, and Repeater functionality.
Package Contents
- FENVI 300Mbps Wireless WiFi Repeater
- User Manual (this document)
2. Device Overview
The FENVI WiFi Repeater features a compact, wall-mount design for easy placement. It includes a LAN port, a Reset button, and LED indicators for power, WiFi signal strength, and network activity.

Figure 2: The WiFi Repeater emphasizing its easy installation and wall-mount design, capable of 300Mbps.
Working Modes
The device supports two primary working modes:
- Repeater Mode: Extends the range of your existing wireless network. It connects wirelessly to your main router and rebroadcasts the signal.
- AP (Access Point) Mode: Creates a new wireless network from a wired Ethernet connection. It connects to your modem or router via an Ethernet cable and provides Wi-Fi access.

Figure 3: Diagram illustrating the two working modes. In Repeater Mode, the device wirelessly extends the router's signal. In AP Mode, it connects via RJ45 cable to a modem/router to create a wireless network.
3. Setup Instructions
This section details how to set up your FENVI WiFi Repeater using a mobile phone. For optimal setup, place the extender near your main router initially. After configuration, you can relocate it to a desired area.

Figure 4: Comprehensive setup guide for the Wireless Range Extender using a mobile phone, detailing steps for both Repeater and AP modes.
3.1. Factory Reset (If needed)
If you encounter issues during setup or wish to clear previous configurations, perform a factory reset:
- With the device powered on, use a paperclip or a thin pin to press and hold the "Reset" hole on the bottom of the product for approximately 8 seconds.
- Release the button when the lights flash, indicating a successful reset.
3.2. Repeater Mode Setup (Mobile Phone)
- Power On: Plug the WiFi extender into a power outlet near your main router. Wait for about 30-60 seconds until the power indicator light turns on steadily.
- Connect to Extender's Wi-Fi: On your mobile phone, go to Wi-Fi settings. Find and connect to the Wi-Fi network named "wifi-XXXX" (where XXXX are the last 4 digits of the MAC address found on the back of the product). There will be no internet access at this stage.
- Access Setup Page: Open a web browser on your phone (e.g., Chrome, Safari) and enter the default IP address:
192.168.188.1in the address bar. - Login: When prompted, enter the default password:
admin. - Scan for Networks: The device will scan for available Wi-Fi networks. Select your main host router's SSID (network name) from the list.
- Enter Host Router Password: Enter the Wi-Fi password for your main host router. Ensure the password is correct and does not contain special characters that might cause issues.
- Set Extender SSID and Password (Optional): You can choose to keep the same SSID as your main router or set a new SSID and password for the extended network (e.g., "YourNetworkName_EXT").
- Confirm and Connect: Review the settings. Click "Start Connect" or "Apply" and wait for 30-60 seconds for the repeater to connect to your router.
- Verify Connection: The "WiFi" LED indicator on the extender should light up steadily, indicating a successful connection in Repeater Mode.
- Reconnect to Extended Network: On your mobile phone, disconnect from "wifi-XXXX" and connect to your newly configured extended Wi-Fi network (e.g., "YourNetworkName_EXT" or your original network if you kept the same SSID). You should now have internet access.
3.3. AP Mode Setup
To use the device as an Access Point:
- Factory Reset: Perform a factory reset as described in Section 3.1.
- Connect to Extender's Wi-Fi: Follow Step 1 and 2 from Repeater Mode Setup (Section 3.2) to connect to "wifi-XXXX" and access the setup page (
192.168.188.1). - Login: Enter the default password:
admin. - Select AP Mode: On the setup page, look for an option like "AP Settings" or "Working Mode" and select "AP Mode".
- Set Wireless Password: Configure the Wi-Fi name (SSID) and password for your new wireless network. For encryption, it is generally recommended to select "WPAPSKWPA2PSK/AES". Click "Apply".
- Connect Ethernet Cable: Connect an Ethernet cable from your modem or router's LAN port to the LAN port on the FENVI WiFi Repeater.
- Verify: The repeater will now broadcast a new Wi-Fi network with the SSID and password you configured. Connect your devices to this new network.
4. Operating the Device
4.1. LED Indicators
- Power LED: Solid blue when the device is powered on.
- WiFi LED: Solid blue when the device is connected to a network (Repeater or AP mode). Blinking indicates activity.
- Signal Strength LEDs: Indicate the strength of the signal received from the main router (in Repeater Mode). More LEDs lit means a stronger signal.
4.2. Optimal Placement
For best performance in Repeater Mode, place the extender halfway between your main router and the area with poor Wi-Fi coverage. Ensure it receives a good signal from the main router (check signal strength LEDs) while also being close enough to the devices you want to connect.
5. Maintenance
- Cleaning: Use a soft, dry cloth to clean the device. Do not use liquid cleaners or aerosols.
- Ventilation: Ensure the device is placed in a well-ventilated area and its vents are not obstructed.
- Firmware Updates: Check the manufacturer's website periodically for firmware updates. Follow the provided instructions carefully if an update is available.
6. Troubleshooting
- No Power: Ensure the device is securely plugged into a working power outlet.
- Cannot Access Setup Page (192.168.188.1):
- Ensure your device is connected to the extender's Wi-Fi ("wifi-XXXX").
- Try a different web browser or clear your browser's cache.
- Perform a factory reset and try again.
- No Internet After Setup:
- Verify that your main router has an active internet connection.
- Ensure you entered the correct Wi-Fi password for your main router during setup.
- Try relocating the extender closer to your main router to ensure a strong signal.
- Perform a factory reset and reconfigure.
- Slow Speed or Weak Signal:
- Relocate the extender to an optimal position (refer to Section 4.2).
- Ensure there are no physical obstructions (thick walls, metal objects) between the extender and your devices, or between the extender and your main router.
- Check for interference from other electronic devices (microwaves, cordless phones).
- Wi-Fi Connected, No Internet (Specific to AP Mode):
- Ensure the Ethernet cable is securely connected from your modem/router to the extender's LAN port.
- Verify that the modem/router providing the wired connection has internet access.
- Repeater Not Visible in Wi-Fi List:
- Ensure the device is powered on.
- Perform a factory reset.
7. Specifications
| Feature | Specification |
|---|---|
| Model Name | 300M WIFI Repeater |
| Brand | fenvi |
| Frequency Band Class | Single-Band |
| Frequency | 2.4 GHz |
| Wireless Communication Standard | 802.11.n |
| Wireless Transmission Rate | 300 Mbps |
| Wi-Fi Transmission Standard | 802.11n |
| Wi-Fi Supported Frequency | 2.4G |
| WAN Ports | 1 x 10/100Mbps |
| LAN Ports | 0 (WAN port doubles as LAN in AP mode) |
| Supports WPS | Yes |
| Supports WDS | No |
| Function | Firewall |
| Certification | CE |
| Application | Soho (Small Office/Home Office) |
8. User Tips
- Initial Setup Location: Always perform the initial setup with the repeater physically close to your main router for a stable connection during configuration.
- Password Accuracy: Double-check your main router's Wi-Fi password during setup. Incorrect passwords are a common cause of connection failures.
- Placement for Performance: Experiment with different locations to find the best spot. A good rule of thumb is halfway between your router and the dead zone, where the repeater still gets a strong signal from the router.
- AP Mode for Wired Devices: If you have a device with only an Ethernet port (like some older smart TVs or printers) but no Wi-Fi, you can use the repeater in AP mode (or client mode if supported) to provide it with network access via its LAN port.
- Reset as First Step: If you encounter persistent issues or unexpected behavior, a factory reset is often the quickest way to resolve them before reconfiguring.
9. Warranty and Support
For warranty information, technical support, or further assistance, please refer to the seller's contact information or the official FENVI website. Keep your purchase receipt as proof of purchase.
Note: Specifications are subject to change without notice. Please refer to the product packaging or manufacturer's website for the most up-to-date information.