Introduction
This manual provides detailed instructions for the safe and efficient operation of your RETEVIS RT85 Analog Two Way Radio. Please read this manual thoroughly before use and keep it for future reference.
Key Features:
- DOT-MATRIX LCD DISPLAY
- Dual band, dual display, dual standby
- A/B band independent operation
- 200 channels storage and scanning
- FM Radio with 24 stations memory
- Wide/Middle/Narrow band selectable
- VOX 0-7 grade setting
- CTCSS/DCS and scanning
- 1750Hz tone
- Shortcut menu operation mode
- Emergency alert
- DTMF encoding and decoding, remote stun/kill/activate
- ANI function
- 8 group of scrambler
- 2 Tone/5 Tone
- Multiple types for keys lock setting
- Multi display mode

Figure 1: RETEVIS RT85 Walkie Talkie in its charging dock.

Figure 2: Super Quality BK4815 Chip, enhancing performance and stability.
General Safety and Usage Tips
To ensure safe operation and compliance with regulations, please observe the following guidelines:
- Always comply with local government regulations regarding radio usage.
- Turn off the radio in flammable or explosive environments.
- Do not charge or replace the battery in flammable or explosive areas.
- Avoid using the radio near blasting zones or detonators.
- Do not use a radio with a damaged antenna, as it may cause heat injury.
- Maintenance should only be performed by qualified technical personnel; do not attempt to open the radio yourself.
- Turn off the radio in areas sensitive to electromagnetic interference, such as hospitals or healthcare facilities.
- Do not place the radio within the deployment range of an airbag in a vehicle.
- Avoid storing the radio in direct sunlight or hot areas.
- Maintain at least 5 cm distance from the antenna when transmitting.
- If the radio emits unusual odors or smoke, immediately turn it off and contact your dealer.
- Avoid prolonged transmission to prevent overheating and potential injury.
Unpacking and Checking Equipment
Upon receiving your package, inspect it for any damage. Carefully unpack the transceiver and verify all items against the list below. If any items are missing or damaged, please contact your local dealer immediately.
Supplied Items:
- Radio Body (Host)
- Antenna
- Li-ion Battery (1400mAh)
- Charger Kit
- Belt Clip
- Sling
- User Manual
Optional Items:
- Li-ion Battery (3200mAh)
- Adapter

Figure 3: Package Contents of RETEVIS RT85.
Note: The antenna frequency range is indicated on the annular label at the bottom of the antenna.
Charging Battery Pack
Charging Precaution:
- The battery is not fully charged from the factory; charge it before first use.
- For optimal capacity, charge and discharge the battery two or three times.
- Do not short-circuit battery terminals or expose them to fire. Do not disassemble the battery.
- Charge the battery only within the temperature range of 0°C to 45°C.
- Turn off the transceiver while charging to ensure proper charging.
- Do not unplug the power adapter or battery during charging.
- If the battery pack depletes quickly even after a full charge, it indicates the battery is worn out and needs replacement.
- Never charge a wet battery or radio. Dry it thoroughly with a cloth before charging.
- Avoid contact between conductive metals (jewelry, keys) and battery terminals to prevent short circuits and heat generation. Handle batteries carefully.
Charging Operation:
After installing the battery pack, if the battery icon on the display shows empty, it means the battery needs charging. The charger's indicator light will show the charging status:
| Indicator Display | Status |
|---|---|
| Red | Charging |
| Green | Completed |
Installation of Accessories
1. Installation of Battery Pack
- Align the two grooves of the battery with the guide rail on the back of the aluminum shell. Ensure full contact and push the battery up until the battery latch locks.
- To remove the battery, ensure the radio is off, push the battery latch down, and slide the battery out.

Figure 4: Battery installation and removal.
2. Installing and Removing the Antenna
- Align the threaded end of the antenna with the threaded hole at the top of the radio. Rotate the antenna clockwise until it is tight.
- To remove, rotate the antenna counter-clockwise until it spirals out.

Figure 5: Antenna installation and removal.
3. Installing Belt Clip
Align the two holes of the belt clip with the two holes on the radio. Fix them with the supplied M2.5x5 screws. To remove, loosen the screw set.

Figure 6: Belt clip accessory.
4. Installing External Micro/Speaker
Open the cover of the Mic/Speaker jack and insert the microphone/speaker plugs into the jack.

Figure 7: External micro/speaker jack location.
Radio Overview and Controls
Radio Illustration:

Figure 8: Front and side view of the RT85 with labeled components.
- Antenna: For transmitting and receiving signals.
- Indicator: LED light for status indications.
- Speaker: For audio output.
- Power/Volume Button: To turn the radio on/off and adjust volume.
- Microphone: For voice input.
- LCD Display: Dot-matrix screen for information display.
- Function/Enter Key (F): Used to enter menu mode and confirm settings.
- A/B Switch Key/Exit (A/B): Switches between A and B frequency bands, also used to exit menus.
- Numeral Keys (0-9, *, #): For frequency input, channel selection, and special functions.
- Side Button 1 (Flashlight/1750Hz): Short press for flashlight, long press to activate 1750Hz tone for repeater access and DTMF/2/5 tone signaling.
- Side Button 2 (PTT): Press to transmit, release to receive.
- Side Button 3 (MONI): Disables squelch to hear very weak signals.
- MIC/SP Jack: Provides connection points for external microphone, earphone, speaker, and programming cable.
LCD Display Icons:
The LCD displays various icons indicating the radio's status and active functions:
| Icon | Description |
|---|---|
| Tatl | Operating band signal & power meter |
| H | High TX power active |
| DH | Dual watch/standby active |
| S | RX power save active |
| Scanning active | |
| Narrow/wide band mode active | |
| + | Repeater shift direction |
| Keypad lock | |
| DT | DTMF signal active |
| 2T | 2 Tone signaling active |
| 5T | 5 Tone signaling active |
| Battery power indicator | |
| 125 | Channel number/Menu items number indicator |
Keypad Functions:
| Key | Function |
|---|---|
| [F] | Enter menu mode / confirm settings |
| [A/B] | Switch A or B frequency band / Exit function |
| [▲] | Navigate up in menus, channels, or frequencies |
| [▼] | Navigate down in menus, channels, or frequencies |
| [*] | Long press to start keypad lock / Short press to enter FM radio (in some modes) |
| [#] | Switch CH mode and VFO mode / Long press to enter FM radio |
Operating Modes
The RETEVIS RT85 supports several operating modes:
- Frequency Mode (VFO): Allows direct frequency input via keypad or selection using the A/B key. Channels can be stored in this mode.
- Frequency-Channel Mode (MR): After storing at least one memory channel, press the [#] key from VFO mode to enter MR mode. Displays frequency and channel number.
- Channel Mode (CH): After storing at least one memory channel, power on the radio while pressing the [#] key to enter CH mode. Displays channel number and name (if display name option is active).
- FM Radio Mode: Provides FM radio reception from 64.00-108.00MHz. Frequencies can be selected directly, scanned, and stored. Long press [#] to enter and exit FM radio mode.
- MENU Mode: Press the [F] key to access the main menu with 36 configurable items.
- RESET Mode: To reset the radio, press [F] + [3] + [5] keys, then press [F] to confirm. Options include ALL (all settings), VFO (frequency mode settings), and FULL (frequency and channel mode settings).
Video 1: Demonstration of key functions including VFO mode, scan mode, power selection, and dual standby.
Technical Specifications
General:
| Parameter | Value |
|---|---|
| Channel Capacity | 200 |
| Operating Voltage | 7.4VDC |
| Operating Temperature | -10°C ~ +50°C |
| Weight | 225g (battery and antenna included) |
| Dimensions (without antenna) | 116x53x36mm |
Transmitter:
| Parameter | Value |
|---|---|
| Frequency Range | 136.000-174.000MHz & 400.000-480.000MHz |
| Output Power | 5W (3w-5w) |
| Modulation Type | FM |
| Spurious Power | ≤-15dB |
| Modulation Noise | <-40dB |
| Modulation Distortion | <5% |
| Frequency Stability | 5ppm |
| Max Fr. Deviation | ≤±5KHz |
| Current | ≤1600mA |
| Audio Response (300-3400Hz) | +6.5~-14dB |
| Adjacent Ch Power | ≥65dB |
Receiver:
| Parameter | Value |
|---|---|
| Frequency Range | 136.000-174.000MHz & 400.000-480.000MHz |
| Sensitivity | ≤0.2μV |
| Occupied Bandwidth | ≤16KHz |
| Selectivity | ≥65dB |
| Intermediation | ≥55dB |
| Audio Power | >500mW |
| Audio Distortion | ≤10% |
| Frequency Stability | 5ppm |
| Current | Standby: 60mA, Working: 250mA |
| Audio Response (300-3400Hz) | +7~-12.5dB |
User Tips
- The RT85 is generally considered easy to use by buyers.
- The product is typically well-packaged, though minor box dents may occur during shipping, the contents are usually unharmed.
- The RT85 features a 200-channel capacity and compact dimensions of 116x53x36mm (without antenna).
- It offers a maximum communication range of 3-5km with an output power of 3W-5W and a 1400mAh battery.
- The radio is compatible with 2-pin K-type earpieces/microphones.
- The RT85 is noted to perform better than some other popular models like the Baofeng UV5R.
Warranty and Support
Your RETEVIS RT85 Walkie Talkie comes with a two-year manufacturer's warranty from the date of purchase. For further details, please refer to the official website or contact your dealer.
Warranty Service:
- Contact the seller directly where you purchased the product.
- Provide a receipt or proof of purchase for verification.
- Products may be repaired by an authorized local repair center.
Exclusions from Warranty Coverage:
- Damage caused by accident.
- Damage resulting from misuse, abuse, or unauthorized alterations/repairs.
- If the serial number has been altered, defaced, or removed.
For additional support or to view the full item guides and documents, you may refer to the User Manual (PDF).
