HORACO ZX-SWTG3448S

Contents

HORACO 52 Port L3 Managed Ethernet Switch

Model: ZX-SWTG3448S

User Manual

1. Introduction

This manual provides comprehensive instructions for the installation, configuration, operation, and maintenance of your HORACO ZX-SWTG3448S 52 Port L3 Managed Ethernet Switch. This device is designed for robust network environments, offering advanced Layer 3 management capabilities, high-speed connectivity, and various security features to ensure efficient and reliable network performance.

The switch features 48 Gigabit RJ45 ports and 4 10-Gigabit SFP+ optical ports, making it suitable for demanding network infrastructures requiring high bandwidth and flexible connectivity.

HORACO 52 Port L3 Managed Ethernet Switch front view
Figure 1.1: HORACO 52 Port L3 Managed Ethernet Switch (Model: ZX-SWTG3448S)

2. Safety Information

Please read and follow all safety instructions carefully to prevent injury or damage to the device. Keep this manual for future reference.

  • Electrical Safety: Ensure the power supply voltage matches the switch's requirements. Do not operate the switch with a damaged power cord.
  • Environment: Install the switch in a well-ventilated area, away from direct sunlight, heat sources, and moisture. Maintain proper airflow around the device.
  • Handling: Avoid dropping or subjecting the switch to severe impact.
  • Maintenance: Do not open the switch casing. Refer all servicing to qualified personnel.
Lightning Protection diagram for network switch
Figure 2.1: Lightning Protection for Network and Power Ports

The device is equipped with lightning protection for both network ports and the power supply to enhance durability and reliability.

3. Package Contents

Verify that all items are present in your package:

  • HORACO ZX-SWTG3448S L3 Managed Ethernet Switch
  • Power Cord
  • Rackmount Kit (brackets and screws)
  • User Manual (this document)

4. Product Overview

4.1 Key Features

  • 52 Ports: 48 x 10/100/1000Mbps RJ45 Ports, 4 x 10G SFP+ Ports, 1 x RJ45 Console Port, 1 x USB Port.
  • L3 Management: Supports IPv4/IPv6 static routing, RIP V1/V2, OSPF.
  • High Performance: Powered by a Ruiyu smart chip for powerful performance without jamming or delay.
  • Multiple Management Functions: QoS, SNMP, VLAN Support, DHCP/VLAN/MAC Address/ACL/QOS/Multicast/Storm Control.
  • Network Redundancy: Supports Ethernet Ring/STP/RSTP/MSTP.
  • Security: 802.1X Authentication, ARP Intrusion Detection, IP Source Guard, DoS Protection.
  • Management Methods: Supports Web/Telnet/CLI/SSH management.
Powerful Chip diagram for network switch
Figure 4.1: Powerful Chip for Optimal Performance
Multiple Management Functions diagram for network switch
Figure 4.2: Overview of Multiple Management Functions (QoS, SNMP, VLAN, DHCP, etc.)

5. Setup and Installation

5.1 Physical Installation

The switch can be installed on a desktop or rack-mounted.

  • Desktop Installation: Place the switch on a flat, stable surface. Ensure adequate ventilation around the device.
  • Rack-Mounted Installation: Use the provided rackmount kit to install the switch into a standard 19-inch equipment rack. Secure the brackets to the switch and then to the rack using appropriate screws.
Rack Mounted Installation example for network switch
Figure 5.1: Rack Mounted Installation (Note: Rack lugs may need to be purchased separately)

5.2 Initial Network Connection

  1. Connect your computer to any RJ45 port on the switch using an Ethernet cable.
  2. Connect the switch to a power source using the provided power cord.
  3. Power on the switch.

5.3 Web Page Login

To access the switch's management interface:

  1. Configure your PC's IP address to be in the same network segment as the switch but with a different IP address (e.g., if the switch is 192.168.2.1, set your PC to 192.168.2.x where x is between 2 and 254). Set the subnet mask to 255.255.255.0.
  2. Open a web browser (Chrome 23.0+, Firefox 20.0+, or IE 9.0+).
  3. Type the default switch IP address into the address bar: http://192.168.2.1 and press Enter.
  4. A login window will appear. Enter the default username admin and password admin.
  5. Click "Log in" to access the switch system.

6. Operating Instructions

The switch offers a comprehensive web-based management interface. Below are key operational areas.

6.1 System Status

View real-time information about the switch's operation.

  • System Information: Displays product details, port states, device states, and function on/off states. Navigate to Status > System Information.
  • Port Statistics: Provides detailed flow statistics for each port. Access via Status > Port > Statistics.
  • MAC Address Table: View dynamic and static MAC address entries. Found under Status > MAC Address Table.

6.2 Network Configuration

  • Management IP Address: Configure the switch's IP address via Routing > IPv4 Management and Interfaces > IPv4 Interface.
  • DNS: Configure DNS settings for the switch under Network > DNS.
  • System Time: Set the system time, time source, and daylight-saving time via Network > System Time.

6.3 Port Management

Configure individual port settings and advanced features.

  • Port Setting: Configure speed, duplex, and flow control for Ethernet ports. Navigate to Port > Port Setting.
  • Link Aggregation (LAG): Bundle multiple physical interfaces into a single logical interface for increased bandwidth and reliability. Configure groups and LACP settings under Port > Link Aggregation.
  • Port Security: Restrict MAC addresses allowed on a port to prevent unauthorized access. Access via Port > Port Security.
  • Mirroring: Copy traffic from a source port to a destination port for monitoring and troubleshooting. Configure rules under Port > Mirroring.

6.4 VLAN Configuration

Divide your network into logical segments for improved security and efficiency.

  • Create VLAN: Define new VLANs and assign IDs. Go to VLAN > VLAN > Create VLAN.
  • VLAN Configuration: Assign ports to VLANs (tagged/untagged membership). Configure via VLAN > VLAN > VLAN Configuration.
  • Voice VLAN: Prioritize voice traffic. Configure OUI and port settings under VLAN > Voice VLAN.
  • MAC VLAN: Assign VLANs based on MAC addresses. Configure groups and bindings under VLAN > MAC VLAN.
VLAN Function Network Division diagram
Figure 6.1: VLAN Function for Network Division (e.g., Finance, R&D, Business Departments)

6.5 DHCP Management

Configure DHCP services for automatic IP address assignment.

  • IP Pool Setting: Define IP address ranges for DHCP clients. Access via DHCP > IP Pool Setting.
  • DHCP Snooping: Enhance network security by preventing unauthorized DHCP servers and ensuring clients obtain IP addresses from legitimate sources. Configure properties and port settings under Security > DHCP Snooping.

6.6 Routing

Configure Layer 3 routing functionalities.

  • IPv4/IPv6 Interfaces: Configure IP addresses for VLAN interfaces. Navigate to Routing > IPv4/IPv6 Management and Interfaces.
  • Static Routes: Define static routes for specific network paths.
  • RIP/OSPF: Configure Routing Information Protocol (RIP) or Open Shortest Path First (OSPF) for dynamic routing.

6.7 Security Features

Implement various security measures to protect your network.

  • ACL (Access Control List): Filter packets based on defined rules (MAC, IPv4, IPv6). Configure under ACL menu.
  • DoS Protection: Enable protection against Denial of Service attacks. Access via Security > DoS.
  • Dynamic ARP Inspection (DAI): Prevent ARP spoofing attacks. Configure under Security > Dynamic ARP Inspection.
  • IP Source Guard: Prevent IP address spoofing. Configure under Security > IP Source Guard.
  • Authentication Manager: Manage 802.1x, MAC-Based, and WEB-Based authentication for network access control. Access via Security > Authentication Manager.

6.8 QoS (Quality of Service)

Prioritize network traffic to ensure optimal performance for critical applications.

  • Queue Scheduling: Configure how traffic is queued and prioritized (Strict Priority, WRR). Access via QoS > General > Queue Scheduling.
  • CoS/DSCP/IP Precedence Mapping: Map different traffic classes to specific priority levels. Configure under QoS > General.
  • Rate Limit: Control ingress and egress bandwidth on ports. Configure under QoS > Rate Limit.

7. Maintenance

7.1 Firmware Management

  • Upgrade: Update the switch firmware to the latest version. Navigate to Management > Firmware > Upgrade.
  • Active Image: Activate a specific firmware image (e.g., after an upgrade). Access via Management > Firmware > Active Image.

7.2 Configuration Management

  • Save Configuration: Save the current running configuration to startup configuration. Go to Management > Configuration > Save Configuration.
  • Backup/Restore: Backup configuration files or restore to factory defaults.

7.3 Diagnostics

Utilize built-in diagnostic tools for network troubleshooting.

  • Logging: View system logs and configure remote log servers. Access via Diagnostics > Logging.
  • Ping/Traceroute: Test network connectivity and trace network paths. Available under Diagnostics.
  • Copper Test/Fiber Module: Diagnose issues with copper cables and SFP fiber modules.

8. Troubleshooting

This section addresses common issues you might encounter with your switch.

8.1 Common Issues & Solutions

  • Cannot Access Web Interface:
    • Ensure your PC's IP address is in the same subnet as the switch (default 192.168.2.x, subnet 255.255.255.0).
    • Verify physical connection between PC and switch.
    • Check if the switch is powered on.
    • Try clearing your browser cache or using a different browser.
  • Network Connectivity Issues:
    • Check port status indicators on the switch.
    • Verify cable connections and integrity (use Copper Test under Diagnostics).
    • Ensure correct VLAN configurations if VLANs are in use.
    • Use Ping and Traceroute tools to diagnose network path issues.
  • Performance Degradation:
    • Check port statistics for errors or high utilization.
    • Review QoS settings to ensure critical traffic is prioritized.
    • Verify Link Aggregation is configured correctly if used for increased bandwidth.
    • Check for network loops using Spanning Tree Protocol status.

9. Specifications

FeatureDescription
Model NumberZX-SWTG3448S
Switch TypeEthernet
Number of Interfaces52 (48*10/100/1000Mbps RJ45, 4*10G SFP+ Port, 1*RJ45 Console Port, 1*USB Port)
Transmission Rate10000 Mbps
Switch Capacity176Gbps
Bandwidth176Gbps
Communication ModeFull-Duplex & Half-Duplex
VLAN SupportSupported (4096 VLANs)
Internet ProtocolSupports IPV4/IPV6
Layer 3 InterfaceSupport Layer 3 interface, IPv4, IPv6 address configuration, ARP configuration, ND configuration
Layer 3 RoutingSupport IPv4 static routing, IPv6 static routing, RIP V1/V2, OSPF
FunctionsQoS, SNMP, VLAN Support, DHCP/VLAN/MAC Address/ACL/QOS/Multicast/Storm Control, Ethernet Ring/STP/RSTP/MSTP, 802.1X Authentication, ARP Intrusion Detection, IP Source Guard, DoS Protection, Web/Telnet/CLI/SSH management
Working Temperature-10℃ - 50℃
Power InputAC 100-240V/50-60Hz
Packet Buffer Memory131Mpps
DDR SDRAM512MB
Flash Memory32MB
Package Cache16Mbit
MAC Address Table Size32K
Jumbo Frame12Kbytes
MTBF (Mean Time Between Failures)100000 hours
CertificationsCE, FCC, RoHS
Dimensions (L x W x H)440mm x 280mm x 44mm
Weight4.6 kg
Product dimensions: 440mm length, 280mm width, 44mm height
Figure 9.1: Product Dimensions

10. User Tips

  • Link Aggregation (LAG) Setup: For aggregating multiple switches, ensure that both switches support Link Aggregation Control Protocol (LACP) and are configured with compatible settings. This allows for increased bandwidth and redundancy between devices. Refer to the 'Port Management' section for detailed configuration steps.
  • Firmware Updates: Regularly check the manufacturer's official website for the latest firmware updates. Keeping your switch's firmware up-to-date ensures optimal performance, security patches, and access to new features. The manual's 'Firmware Management' section provides instructions on how to upgrade the firmware.

11. Warranty and Support

The HORACO ZX-SWTG3448S L3 Managed Ethernet Switch comes with a 2-year warranty. For technical support, troubleshooting assistance, or warranty claims, please contact your vendor or the official HORACO support channels. Refer to the product packaging or official website for contact information.

A detailed user manual in PDF format is available for download from the official product page or can be accessed via the following link: User Manual (PDF).

© 2023 HORACO. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.