Xingxun Car Interior Mirror Frame Ring Cover Trim

Contents

Xingxun Car Interior Mirror Frame Ring Cover Trim User Manual

Model: Car Interior Mirror Frame Ring Cover Trim

Brand: Xingxun

1. Product Information

This product is an automotive decoration accessory designed to enhance the interior aesthetics of specific Mercedes Benz models. It is a matte silver trim piece that adheres to the car's interior mirror frame.

1.1. Compatibility

  • For Mercedes Benz C Class (W205)
  • For Mercedes Benz GLC Class (X253)
  • For Mercedes Benz GLE Class (W166)
  • For Mercedes Benz GLS Class
  • For Mercedes Benz M Class (W166)

1.2. Package Contents

  • 1 x Car Interior Mirror Frame Ring Cover Trim (Matte Silver)

2. Safety & Warnings

Read all instructions before use. Failure to follow these instructions may result in damage to the product or personal injury.

  • Warning: Keep the device and its cord out of reach of children under 3 years old.
  • Keep away from children unless supervised by an adult.
  • Do not use this product for purposes other than its intended use.
  • Inspect the product before each use; do not use if damaged.
  • Follow installation and operation guidelines to avoid injury.

3. Installation Instructions

This trim piece is designed for easy adhesive-based installation. Follow these steps carefully for optimal results.

Matte Silver Car Interior Mirror Frame Ring Cover Trim

Figure 3.1: The Matte Silver Car Interior Mirror Frame Ring Cover Trim.

  1. Preparation: Before first use, remove any protective films from the trim piece.
  2. Clean Surface: Before installation, ensure the target surface on your car's interior mirror frame is thoroughly clean and dry. Use a suitable automotive cleaner to remove dust, grease, and debris.
  3. Confirm Position: Carefully place the trim piece over the mirror frame without removing the adhesive backing to confirm the correct installation position. Ensure it aligns perfectly with the contours of the mirror frame.
  4. Warm Adhesive (if necessary): If the ambient temperature is below 15 degrees Celsius (59 degrees Fahrenheit), gently heat the adhesive tape on the back of the trim piece using a hairdryer or heat gun. This helps to improve adhesion.
  5. Apply Trim: Remove the protective film from the adhesive tape. Carefully align the trim piece with the confirmed position and firmly press it onto the mirror frame. Apply even pressure across the entire surface for several seconds.
  6. Post-Installation Care: Do not touch the installed trim with water or expose it to dust for at least 24 hours after installation. This allows the adhesive to cure properly and ensures a strong bond.
Back of trim showing red adhesive tape

Figure 3.2: Rear view of the trim piece, highlighting the pre-applied adhesive tape.

Before and after installation of mirror trim

Figure 3.3: Visual comparison of the car's interior mirror before and after the trim installation.

4. Operating Instructions

This product is a decorative accessory and does not have any operational functions. Once installed, it serves to enhance the visual appeal of your vehicle's interior mirror.

5. Maintenance

To maintain the appearance of your mirror frame trim, follow these simple guidelines:

  • Cleaning: Wipe the surface with a soft, damp cloth. Avoid abrasive cleaners or solvents that could damage the finish.
  • Avoid Harsh Chemicals: Do not use strong chemical cleaners or polishes directly on the trim, as this may cause discoloration or damage.
  • Regular Inspection: Periodically check the trim for any signs of loosening or damage.

6. Troubleshooting

6.1. Fitment Issues

If the trim piece does not seem to fit your vehicle, please verify the compatibility with your specific Mercedes Benz model and year. This product is designed for Mercedes Benz C, GLC, GLE, GLS, and M Class models (W205, X253, W166). Incorrect model identification is a common reason for fitment problems.

6.2. Adhesive Not Sticking Properly

Ensure the installation surface was thoroughly cleaned and dried before application. If the ambient temperature was below 15 degrees Celsius (59 degrees Fahrenheit), heating the adhesive tape as described in the installation instructions (Step 4) can significantly improve adhesion. Avoid touching the adhesive surface with your fingers, as oils can reduce stickiness.

6.3. Rough Edges / Imperfections

While quality control is maintained, minor imperfections can occur. If you notice significant rough edges or other manufacturing defects that affect the appearance or safety, please contact customer support.

7. Specifications

Attribute Value
Product Name Automotive Decoration Accessories
Model Name Car Interior Mirror Frame Ring Cover Trim
Material ABS Plastic
Color Matte Silver
Item Type Interior Mouldings
Item Weight 0.1kg (approx. 75g packaged)
External Testing Certification ISO9000
High-concerned chemical None
Origin Mainland China
Package Dimensions (L x W x H) 30cm x 8cm x 4cm

8. User Tips

  • Many users appreciate the quality and finish of the product, noting its ability to enhance the car's interior.
  • Ensure to double-check your car's specific model and year against the compatibility list to avoid fitment issues.
  • Take your time during installation to ensure precise alignment and firm adhesion for the best aesthetic outcome.

9. Frequently Asked Questions (FAQ)

Q: Will this trim fit a Honda HR-V 2021?
A: No, this product is specifically designed for Mercedes Benz C, GLC, GLE, GLS, and M Class models (W205, X253, W166) and is not compatible with Honda HR-V models.
Q: Is this compatible with a GLA X156 from 2017?
A: This product is not listed as compatible with the GLA X156 model. Please refer to the compatibility list in Section 1.1.

10. Warranty & Support

For any questions, concerns, or support regarding this product, please contact the manufacturer or their authorized representative.

10.1. Manufacturer Information

Company Name: Luoding Xingxun Network Co., Ltd
Full Address: Nan Yang Hua Yuan No.05, Gong Ye San Lu, Luoding, Guangdong 52720 China
Email: ali_xingxun@outlook.com

10.2. EU Authorized Representative

AR Company Name: ECLAT SOLUTION SARL
Full Address: Bureau 1145, 37 Passage du Ponceau Paris 75002 France
Email: eclatsolution@outlook.com

Please retain your proof of purchase for warranty claims.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.