TAIYEDQ KCT24

Contents

KCT24 Split-Core Current Transformer User Manual

For KCT24 Series Models

1. Product Overview

The KCT24 is a compact, split-core (clip-on type) current transformer designed for accurate AC-current measurement and monitoring without interrupting the main power circuit. It is widely used in energy meters, power distribution systems, industrial control, and electrical monitoring equipment.

For a detailed PDF version of this manual, please refer to the KCT24 User Manual (PDF).

Key Specifications (Typical for KCT24 Series):

  • Model: KCT24
  • Type: Split-Core Current Transformer
  • Accuracy Class: 0.5 / 0.5S (varies by model)
  • Core Opening Diameter: 24mm (suitable for cables/busbars up to Φ24mm)
  • Output: Standard 5A or 1A (matches ratio, e.g., 200A/5A, 100A/5A)
  • Insulation: Class B, suitable for low-voltage systems
  • Certifications: CE Certified
  • Manufacturer: MINGHUI TAIYE ELECTRIC CO., LTD.
  • EU LVD Voltage: Below 50Vac or 75Vdc
  • Phase: SINGLE
  • Use: Current
  • Origin: Mainland China
TAIYEDQ KCT24 Split Core Current Transformers showing various current ratings.
TAIYEDQ KCT24 Split Core Current Transformers showing various current ratings (100A, 150A, 200A, 250A, 300A, 400A).

2. Safety Instructions

WARNING: RISK OF ELECTRIC SHOCK

High Voltage Caution:

This device is intended for use on energized low-voltage AC circuits (<= 690V). Installation and operation must be performed by qualified electricians.
  • Do Not Open Secondary Circuit: Never disconnect the secondary output terminals while the primary current is flowing. This will generate dangerous high voltages and may damage the transformer.
  • Secure Mounting: Ensure the split-core is fully closed and locked around the conductor to avoid inaccurate readings or accidental opening.
  • Insulation Check: Inspect the housing and cables for damage before use. Do not use if cracks or exposed conductors are present.
  • Environmental Limits: Operate in dry, well-ventilated areas. Avoid moisture, dust, oil, and corrosive gases.

3. Installation Guide

3.1 Preparation

  • Identify the AC current-carrying conductor (primary circuit) you wish to measure.
  • Ensure the conductor diameter is ≤24mm to fit the core opening.
  • Prepare the secondary measurement device (ammeter, energy meter, or data logger) that accepts the rated secondary current (e.g., 5A).
Front view of a KCT24 Split Core Current Transformer, highlighting the core opening.
Front view of a KCT24 Split Core Current Transformer, highlighting the 24mm core opening.

3.2 Installation Steps

  1. Open the Core: Press the side latch to open the split-core.
  2. Clip On Conductor: Place the open core around the single primary conductor (live wire). Do not enclose multiple conductors or neutral/ground wires together.
  3. Close & Lock: Snap the core shut until the latch clicks into place, ensuring a tight, secure closure.
  4. Secondary Wiring: Connect the red and black output wires to your measurement device:
    • Red wire: Connect to the positive/input terminal of the measuring device.
    • Black wire: Connect to the negative/return terminal.

    Ensure the secondary circuit is never open-circuited while primary current is present.

KCT24 Split Core Current Transformer in open position, showing the split core mechanism.
KCT24 Split Core Current Transformer in open position, ready for conductor placement.
KCT24 Split Core Current Transformer in closed position, demonstrating secure latching.
KCT24 Split Core Current Transformer in closed position, showing secure latching.
Rear view of a KCT24 Split Core Current Transformer, showing wiring connections and product label.
Rear view of KCT24 showing red and black output wires for secondary connection.

3.3 Polarity Note

For correct phase measurement, ensure the primary current flows in the direction indicated by the arrow (if marked) on the transformer housing relative to your secondary device.

4. Operation Principle

  1. The KCT24 operates on the principle of electromagnetic induction.
  2. When AC current flows through the primary conductor inside the core, it generates an alternating magnetic field.
  3. This magnetic field induces a proportional AC current in the secondary winding, which is output to the connected measuring device.
  4. The output current is precisely scaled according to the transformer's ratio (e.g., 200A primary = 5A secondary for a 200/5A model).

5. Troubleshooting

Problem Possible Cause Solution
Inaccurate reading
  • 1. Core not fully closed
  • 2. Multiple conductors enclosed
  • 3. Incorrect ratio setting on meter
  • 4. Loose secondary wiring
  • 1. Reopen and securely close the core
  • 2. Ensure only one primary conductor is inside
  • 3. Verify meter setup matches CT ratio
  • 4. Tighten all secondary connections
No output signal
  • 1. No current in primary conductor
  • 2. Broken secondary wire
  • 3. Secondary circuit open
  • 1. Check primary circuit is energized
  • 2. Inspect and replace damaged cables
  • 3. Ensure secondary circuit is always closed
Overheating
  • 1. Primary conductor oversized for core
  • 2. Excessive primary current
  • 3. Poor ventilation
  • 1. Use appropriate conductor size ≤24mm
  • 2. Do not exceed rated primary current
  • 3. Improve airflow around the CT

6. Maintenance Guidelines

  • Visual Inspection: Regularly check for cracks, physical damage, or corrosion on the housing and cables.
  • Cleaning: Wipe the exterior with a dry cloth. Do not use water, solvents, or abrasive cleaners.
  • Calibration: For critical applications, have the unit recalibrated annually by a certified laboratory to maintain accuracy class.
  • Replacement: Replace immediately if the core cannot close securely, insulation is damaged, or accuracy drifts beyond acceptable limits.

7. Warranty & Certification

  • CE Certification: Complies with EU safety and EMC standards for electrical equipment.
  • Warranty: This product is warranted against defects in materials and workmanship for 12 months from the date of purchase.
  • Exclusions: Warranty does not cover damage from improper installation, misuse, overloading, water ingress, or unauthorized disassembly.
  • Claims: For support, contact the seller with your order number, model details, and a description of the issue.

8. User Tips

  • Always ensure the split-core is fully closed and latched for accurate readings and to prevent accidental opening.
  • When connecting, pay close attention to the polarity markings (if present) on the transformer housing to ensure correct phase measurement.
  • Never leave the secondary circuit open while the primary circuit is energized, as this can generate dangerous high voltages.
  • If you require specific data sheets for different current ratings (e.g., 150A, 250A), contact the seller for detailed documentation.

9. Frequently Asked Questions (FAQ)

Q: Where can I find detailed data sheets for specific current ratings (e.g., 150A, 250A)?
A: Detailed data sheets for specific current ratings may be available upon request. Please contact the seller directly with your model and current rating requirements.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.