AELED TM1903

Contents

TM1903 Dream Color LED Strip Light User Manual

Model: TM1903 | Brand: AELED

1. Product Overview

The AELED TM1903 Dream Color LED Strip Light is an addressable smart pixel RGB tape designed for dynamic lighting effects. Featuring 180 LEDs per meter and controlled by the TM1903 chipset (compatible with WS2811 protocols), this strip offers full-color capabilities, including water flow, chase, and scan effects. It operates on a 12V DC power supply and is suitable for various decorative and functional lighting applications.

TM1903 LED Strip Light showing rolled and unrolled sections
Figure 1: TM1903 Dream Color LED Strip Light
Video 1: Demonstration of the LED strip's dynamic color effects.

2. Setup Instructions

2.1 Components

Ensure you have the following:

  • TM1903 LED Strip Light (5 meters)
  • Compatible 12V DC Power Supply (not included)
  • Compatible LED Controller for TM1903/WS2811 (not included)
  • Appropriate wiring and connectors

2.2 Wiring Diagram

Follow the wiring diagram below for proper connection. A compatible LED controller is required to operate the strip.

Distribution Wiring Diagram showing power supply, controller, and LED strip connections
Figure 2: Distribution Wiring Diagram. Connect the 12V DC power supply to both the controller and directly to the LED strip for longer runs. The controller's Data and GND lines connect to the strip's Data and GND inputs.

2.3 Power Supply Requirements

  • The LED strip requires a 12V DC power supply. Do not use any other voltage.
  • The power supply capacity (Amps) must be sufficient for the total length of the LED strip. The strip consumes a maximum of 36W per meter. For a 5-meter strip, this is 180W (15 Amps at 12V).
  • The thickness of the power cord should be selected based on the actual maximum current, the product power, the wiring length (not exceeding 5 m), and the pressure drop of the low voltage transmission line.

2.4 Installation Tips

  • Cutting the Strip: The LED strip can be cut to your desired length. Each segment of 3 LEDs is controlled by one IC, allowing for precise customization. Cut only at designated cut marks (usually indicated by a copper pad).
  • Solder Points: It is normal for the strip to have solder points every 0.5 meters. These are manufacturing joints and do not affect performance.
  • Adhesion: The strip typically comes with an adhesive backing for easy installation. Ensure the surface is clean, dry, and smooth before applying.
Diagram showing TM1903 chip, 5050SMD LED, safe resistor, and cuttable points
Figure 3: Key features including the TM1903 IC, 5050SMD RGB LED, safe resistor for stable voltage, and designated cut points.

3. Operating Instructions

Once properly wired and powered, the LED strip's operation is controlled by the external LED controller (not included). Refer to your specific controller's manual for detailed instructions on selecting modes, colors, brightness, and speed.

  • Dynamic Effects: The TM1903 chipset enables a wide range of dynamic effects such as full-color water flow, chasing, and scanning.
  • Color Control: Enjoy full RGB color control, allowing for millions of color combinations.
  • Brightness Adjustment: Adjust the brightness levels via your controller to suit your environment.
Application examples in various rooms
Figure 4: Examples of LED strip applications in living rooms, kitchens, bedrooms, game rooms, and behind TVs.

4. Maintenance

  • Cleaning: Gently wipe the LED strip with a dry, soft cloth to remove dust. Do not use abrasive cleaners or excessive moisture.
  • Water Resistance: This LED strip has an IP30 rating, meaning it is non-waterproof. Avoid exposure to water, high humidity, or outdoor elements unless housed in a protective enclosure.
  • Inspection: Periodically check connections for any signs of wear or damage.

5. Troubleshooting

  • Strip Not Lighting Up:
    • Check if the 12V DC power supply is correctly connected and functioning.
    • Verify all wiring connections (power, ground, data) are secure and correctly oriented.
    • Ensure the LED controller is powered on and sending signals.
    • Check for any physical damage or breaks in the LED strip.
  • Incorrect Colors or Flickering:
    • Ensure the LED controller is configured for the correct chip type (TM1903/WS2811) and LED count.
    • Check data line connections for looseness or interference.
    • Verify the power supply is adequate for the entire strip length. Voltage drop can cause issues over long runs.
  • Partial Strip Not Lighting:
    • Inspect the unlit section for physical damage or a faulty connection point.
    • This could indicate a localized power or data issue within that segment.

6. Specifications

FeatureSpecification
Model NumberTM1903
LED Source5050SMD RGB External TM1903 chipset
IC TypeTM1903 (compatible with WS2811)
Working Input Voltage12V DC
Output Power (per LED)0.2W
Drive ModeConstant Voltage
LED Quantity180 LEDs/Meter (3 LEDs separately controlled)
IC Quantity60 ICs/Meter (1 IC drives 3 LED chips)
Pixels60 Pixels/Meter
Grey Scale256
ColorRGB (Full Color)
View Angle120°
Working Temperature-20°C to 60°C
PCB ColorWhite PCB
Waterproof RatingIP30 (Non-waterproof)
PCB Width16mm
Power ConsumptionMax 36W/Meter
CertificationCE, RoHs
Luminous Flux60-249 Lumens
Average Life100,000 hours
LED Chip BrandCree

7. User Tips

  • Controller Compatibility: Always ensure your LED controller is specifically designed to work with TM1903 or WS2811 addressable LEDs for optimal performance and effect synchronization.
  • Power Calculation: Accurately calculate the required power supply wattage based on the total length of your LED strip to prevent dimming or damage. It's always good practice to use a power supply with a 10-20% higher wattage than your calculated maximum.
  • Voltage Drop: For installations longer than 5 meters, consider injecting power at multiple points along the strip to counteract voltage drop and maintain consistent brightness and color accuracy.

8. Warranty and Support

For warranty information, please refer to the terms and conditions provided by your retailer or contact the seller directly. Keep your proof of purchase for any warranty claims.

An additional user manual in PDF format may be available for download: View User Manual (PDF)

© 2023 AELED. All rights reserved.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.