Dooya DM45R 50/12

Contents

Dooya Tubular Motor DM45R User Manual

Model: DM45R 50/12

Introduction

This manual provides detailed instructions for the installation, operation, maintenance, and troubleshooting of your Dooya DM45R Tubular Motor. This motor is designed for motorized rolling blinds and features a built-in 433MHz receiver for remote control operation. Please read this manual thoroughly before installation and use to ensure safe and efficient operation.

For additional guides and documents, you may refer to the official user manual PDF: Dooya DM45R User Manual (PDF).

Important Safety Warnings

Failure to follow these instructions may result in serious injury or property damage. Please adhere to all warnings.

  • Always ensure all irrelevant power lines are removed and all equipment not required for power supply is disabled before installing the motor.
  • The manual control mechanism should be installed at a height not exceeding 1.8 meters.
  • Self-resetting switch actuators must be installed within the direct line of sight of the driven component and away from moving parts, at a height not less than 1.5 meters.
  • Do not allow children to play with fixed control switches. Remote controls should be kept out of reach of children.
  • Regularly check that the installation is balanced.
  • Do not store the motor with strong acids, alkalis, or corrosive materials.
  • Do not use the motor in humid environments.
  • Do not use the motor for residential garage doors, except for specific garage door motors.
  • Avoid frequent starting or overloading the motor to prevent reducing its service life.
  • Do not rotate adjustment knobs or drive tubes when the motor is not in operation.
  • Moving parts of the motor must be installed at least 2.5 meters above the ground or any accessible platform.
  • Do not operate the awning when performing maintenance or opening windows, e.g., when cleaning windows.
  • If the power cord is damaged, it must be replaced by a professional.
  • If the motor is damaged, it must be repaired or replaced by a professional.
  • If the motor is used for awnings, ensure that the fully extended awning maintains a horizontal distance of more than 0.4 meters from surrounding fixed objects.
  • Fixed controllers must be installed in a visible location.
  • If the motor is used for roller doors, ensure the roller door is fully closed and personnel are clear before operation.
  • When manually operating the motor, be aware of personnel safety. Roller doors may fall rapidly due to spring wear or breakage.

Setup and Installation

Package Contents

The package includes the Dooya DM45R Tubular Motor. Other accessories for rolling blinds (e.g., remote controls, brackets, tubes, fabric) may need to be purchased separately.

Dooya DM45R Tubular Motor in its packaging
Dooya DM45R Tubular Motor as packaged.

Installation Method

The installation method depends on whether the blind is mounted inward or outward relative to the window frame. The length of the tube (B) is determined by the width of the window (A).

  • Inward Mounting: Tube length (B) = Window width (A) - 2cm.
  • Outward Mounting: Tube length (B) = Window width (A) + 2cm.
Diagram showing inward and outward installation methods for roller blinds, illustrating how to calculate tube length based on window width.
Installation methods for roller blinds: Inward (tube length = window width - 2cm) and Outward (tube length = window width + 2cm).

Motorized Roller Blind Solution Components

A complete motorized roller blind solution typically includes the following components:

  • Tubular Motor (DM45R)
  • Drive Adapter (DL01)
  • Wall Bracket (DZ319B)
  • Idler Bracket (DZ318B)
  • Driving Tube (DG02)
  • Fabric
  • Bottom Beam
  • Single-channel emitter (remote control)
Diagram illustrating the components of a motorized roller blind solution, including the tubular motor, drive adapter, wall bracket, idler bracket, driving tube, fabric, bottom beam, and single-channel remote control.
Components of a motorized roller blind solution.

Wiring Diagram

The motor operates on 230V/50Hz AC power. Ensure proper electrical connections as shown in the diagram below. Incorrect wiring can lead to malfunction or damage.

Detailed wiring diagram for the Dooya DM45R tubular motor. The power line connections are: Brown to Live (L), Blue to Neutral (N), and Green/Yellow to Earth (E). The dry contact lines are: Yellow to Common, Red to Up, Black to Down, and Green for no function.
Electrical wiring diagram for the DM45R motor.

Power Line Connections (230V/50Hz):

  • Brown wire: Live (L)
  • Blue wire: Neutral (N)
  • Green/Yellow wire: Earth (E)

Dry Contact Line Connections:

  • Yellow wire: Common
  • Red wire: Up
  • Black wire: Down
  • Green wire: No function

Operating Instructions

The DM45R motor features a built-in receiver and requires a remote control for operation. The remote control allows for movement (up/down), limit setting, and dimming functions.

Image of a Dooya DC2700 single remote controller with buttons for up, down, stop, and intermediate positions.
Dooya DC2700 Single Remote Controller.

1. Remote Control Pairing (1.1 Pairing)

  1. Power Off: Disconnect power to the motor.
  2. Power On: Reconnect power to the motor. The motor will emit a short 'beep' sound (嘀 x1).
  3. Press P2: Within 65 seconds of powering on, press the P2 button on the remote control. The motor will emit a short 'beep' (嘀 x1).
  4. Press Up: Press the 'Up' button on the remote control. The motor will emit three short 'beeps' (嘀 x3), indicating successful pairing.

2. Direction Reversal (1.2 Reversal)

If pressing the 'Up' button on the remote causes the blind to move down, you need to reverse the motor's direction.

  1. Power Off: Disconnect power to the motor.
  2. Power On: Reconnect power to the motor. The motor will emit a short 'beep' sound (嘀 x1).
  3. Press P2: Within 65 seconds of powering on, press the P2 button on the remote control. The motor will emit a short 'beep' (嘀 x1).
  4. Press Down: Press the 'Down' button on the remote control. The motor will emit three short 'beeps' (嘀 x3), indicating successful direction reversal.

3. Adding Transmitters (1.3 Add Transmitter)

To control the same set of blinds with multiple remote controls, follow these steps. This procedure assumes you have at least one remote already paired.

  1. Press P2 (Paired Remote): On an already paired remote, press the P2 button. The motor will emit a short 'beep' (嘀 x1).
  2. Press P2 (New Remote): On the new remote you wish to pair, press the P2 button. The motor will emit a short 'beep' (嘀 x1).
  3. Press Up (New Remote): Press the 'Up' button on the new remote. The motor will emit five short 'beeps' (嘀 x5), indicating successful addition of the new transmitter.

4. Travel Limit Setting (2 Travel Setting)

The motor has mechanical limits that need to be set for the upper and lower travel positions of the blind.

  • Upper Limit Adjustment: Use the adjustment screw for Group A. Turn counter-clockwise to decrease the travel distance until the motor stops, then turn clockwise to gradually increase the travel to the desired upper limit.
  • Lower Limit Adjustment: Similarly, use the adjustment screw for Group B to set the lower limit.
Close-up of the motor's end cap showing the adjustment screws for setting travel limits.
Motor end cap with travel limit adjustment screws (Group A and Group B).

5. Jog Mode and Dimming (3.1 Jog Mode)

For standard remote controls, short-pressing the 'Up' or 'Down' button will cause the motor to jog (move incrementally). Long-pressing for 2 seconds or more will initiate continuous movement. For dimming remotes, this function is automatically handled.

  1. Activate/Cancel Jog Mode: Press P2 on the remote (嘀 x1), then press the 'Up' button (嘀 x1), then press P2 again (嘀 x3). This will activate or cancel jog mode.

6. Deleting All Transmitters (3.2 Delete All Transmitters)

To clear all paired remote controls from the motor's memory:

  1. Press P2: Press the P2 button on any paired remote. The motor will emit a short 'beep' (嘀 x1).
  2. Press P2 again: Press the P2 button again. The motor will emit a short 'beep' (嘀 x1).
  3. Press P2 a third time: Press the P2 button a third time. The motor will emit four short 'beeps' (嘀 x4), indicating all transmitters have been deleted.

Specifications

The Dooya DM45R Tubular Motor is designed for robust performance in various applications. Below are the key technical specifications:

Dooya Tubular Motor DM45R-50/12 with a label showing detailed specifications including torque, speed, voltage, frequency, power, current, running time, IP rating, and maximum load.
DM45R-50/12 Motor with specifications label.
DM45R Series Technical Data (230V / 50Hz)
Product Model Rated Torque (N.m) Rated Speed (RPM) Wireless Frequency (MHz) Rated Voltage (V) Protection Class (IP) Max Limit Turns Working Temp. (°C)
DM45R-10/15 10 15 433.92 230 44 36 -20~60
DM45R-20/15 20 15 433.92 230 44 36 -20~60
DM45R-30/15 30 15 433.92 230 44 36 -20~60
DM45R-40/15 40 15 433.92 230 44 36 -20~60
DM45R-50/12 50 12 433.92 230 44 36 -20~60
DM45R-60/8 60 8 433.92 230 44 36 -20~60

Note: Specifications are based on the nameplate. For motor operation outside the -20°C to 60°C temperature range, please consult Dooya company.

Additional Specifications:

  • Model Number: DM45R 50/12
  • Voltage: 220-240V
  • Wattage: 0W (This might indicate power consumption is very low or not specified in watts, but rather in current/torque)
  • Origin: Mainland China
  • Certification: CE
  • Communication Interface: Wireless (433MHz)
  • Max Load: 116kg
  • EU LVD Voltage: High voltage: Above 50Vac or 75Vdc
  • Battery Included: No

Noise Level

The motor is designed for quiet operation, with noise levels typically between 5-15dB, comparable to very quiet environments.

Diagram illustrating different noise levels, showing the motor's noise level of 5-15dB as 'Very Quiet', compared to quiet room (15-40dB), loud speech (40-60dB), and noisy street (60-80dB).
Motor noise level comparison.

Maintenance

  • Regularly inspect the motor and blind system for any signs of wear or damage.
  • Keep the motor clean and free from dust and debris. Use a soft, dry cloth for cleaning.
  • Do not use harsh chemicals or abrasive cleaners on the motor or its components.
  • Ensure all mounting hardware remains secure. Tighten any loose screws as needed.
  • If the motor stops unexpectedly during operation, it may be due to overheating. Allow approximately 20 minutes for the motor to cool down before resuming operation.

Troubleshooting

Common Problems and Solutions
No. Symptom Cause Solution
1 After power-on, the roller only moves in one direction. The internal limit switch of the motor is not open. Rotate the crown one turn in the opposite direction of the roller's rotation to activate it.
2 Motor does not run or starts slowly after installation and power-on. a. Power supply voltage is too low.
b. Incorrect wiring.
c. Overload.
d. Improper installation.
a. Adjust to rated power supply.
b. Check and correct wiring.
c. Ensure load is within rated torque.
d. Reinstall the motor correctly.
3 Motor stops suddenly during operation. Exceeded the motor's rated continuous operating time (typically 4 minutes). Wait approximately 20 minutes for the motor to cool down, and it will automatically resume operation.
4 Abnormal noise during blind operation. The driving tube is too long, causing the entire blind assembly to press too tightly against the side brackets. If the end plug is movable, shorten the driving tube appropriately to ensure the blind assembly does not press too tightly against the side brackets.

User Tips

  • For optimal performance, ensure the motor is installed by a qualified professional.
  • When setting limits, make small adjustments and test the travel after each adjustment to achieve precise positioning.
  • If you experience issues with remote control range, ensure there are no obstructions between the remote and the motor's receiver.
  • Consider using multi-channel remotes if you have several blinds to control independently or in groups.

Warranty and Support

Warranty Information

This product comes with a 1-year manufacturer's limited warranty for defective items, excluding items damaged or misused after receipt. Accessories typically come with a 3-month warranty.

Defective items must be reported and returned within the warranty period, preferably in their original packaging. Please provide your order number and a description of the defect.

Customer Support

For any questions, technical assistance, or troubleshooting not covered in this manual, please contact Dooya customer service or your authorized dealer.

Dooya Customer Service Hotline: 400-005-8888

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.