SUNON KDE1204PKVX

Contents
SUNON Logo

SUNON KDE1204PKVX Server Cooling Fan

Instruction Manual

Introduction

This manual provides detailed instructions for the installation, operation, and maintenance of your SUNON KDE1204PKVX DC12V 1.4W Server Cooling Fan. Please read this manual thoroughly before using the product to ensure proper function and longevity.

Safety Information

  • Ensure the power supply is disconnected before installation or maintenance.
  • Handle the fan by its frame, avoiding contact with the blades to prevent injury or damage.
  • Do not operate the fan in environments with excessive moisture or extreme temperatures outside its specified operating range.
  • Verify correct voltage and polarity before connecting the fan to a power source.
  • Keep out of reach of children.

Package Contents

Your package should contain the following item:

  • 1 x SUNON KDE1204PKVX DC12V 1.4W Server Cooling Fan
SUNON KDE1204PKVX Fan front view with label
Front view of the SUNON KDE1204PKVX fan, showing the label with model number and specifications.

Specifications

Parameter Value
Model KDE1204PKVX
Dimension 40 x 40 x 20 mm
Fan Speed 8200 RPM
Bearing Type Magnetic Bearing (MagLev)
Noise Level 27.5 dBA
Air Volume 10.8 CFM
Power 1.4 W
Current 0.115 A
Rated Voltage 12 V DC
Fan Interface 3-Pin Connector
Cord Length 8 CM
Service Life 100,000 hours (at 25°C, 45-85% relative humidity)
Origin Mainland China
SUNON KDE1204PKVX Fan top view with label
Top-down view of the fan, clearly showing the SUNON MagLev label and model details.

Setup and Installation

  1. **Prepare the Installation Area**: Ensure the area where the fan will be installed is clean and free of obstructions. Identify the mounting points for a 40x40mm fan.
  2. **Mount the Fan**: Secure the fan to the desired location using appropriate screws (not included). Ensure the fan is oriented correctly for optimal airflow (typically, the label side indicates the direction of airflow out of the fan).
  3. **Connect Power**: Locate the 3-pin connector on the fan cable.
    • **Red Wire**: +12V DC (Positive Power)
    • **Black Wire**: GND (Ground)
    • **Yellow Wire**: Tachometer Signal (RPM Feedback)
    Connect the 3-pin connector to a compatible fan header on your motherboard or power supply. Ensure the pins align correctly to avoid damage.
  4. **Verify Connection**: Double-check all connections before restoring power to your system.
SUNON KDE1204PKVX Fan angled view with 3-pin cable
Angled view of the fan, clearly showing the 3-pin power cable for connection.

Operating Instructions

Once properly installed and connected to a 12V DC power source, the SUNON KDE1204PKVX fan will begin operating automatically. The fan is designed for continuous operation to provide consistent cooling.

  • The yellow wire provides a tachometer signal, allowing compatible systems to monitor the fan's rotational speed (RPM).
  • Ensure adequate space around the fan for unrestricted airflow.

Maintenance

To ensure optimal performance and extend the lifespan of your fan, periodic maintenance is recommended:

  • **Dust Removal**: Regularly inspect the fan blades and frame for dust accumulation. Use compressed air or a soft brush to gently remove dust. Avoid using excessive force or liquids.
  • **Bearing**: The fan utilizes a magnetic bearing (MagLev) design, which is known for its durability and quiet operation, requiring no lubrication.
  • **Inspection**: Periodically check the fan for any signs of wear, damage, or loose connections.
SUNON KDE1204PKVX Fan rear view
Rear view of the fan, showing the blades and mounting points.

Troubleshooting

Problem Possible Cause Solution
Fan not spinning
  • No power or incorrect connection.
  • Fan blades obstructed.
  • Faulty fan.
  • Check power supply and 3-pin connection. Ensure correct voltage (12V DC).
  • Remove any obstructions from the fan blades.
  • Replace the fan if it remains unresponsive after checking power and obstructions.
Excessive noise
  • Dust accumulation on blades.
  • Loose mounting screws.
  • Fan rubbing against an object.
  • Clean fan blades and frame.
  • Tighten mounting screws.
  • Ensure nothing is touching the fan blades or frame.
Poor cooling performance
  • Restricted airflow.
  • Incorrect fan orientation.
  • Clear any obstructions blocking air intake or exhaust.
  • Ensure the fan is pushing air in the desired direction for cooling.

User Tips

  • **Optimal Airflow**: When installing, consider the overall airflow direction within your system. Fans typically have an arrow indicating airflow direction on the side of the frame.
  • **Cable Management**: Route the 3-pin cable neatly to prevent it from interfering with other components or the fan blades.
  • **Regular Checks**: Periodically check the fan's operation, especially in critical server environments, to ensure consistent cooling and prevent overheating.

Warranty and Support

For any issues not covered in this manual, or for warranty inquiries, please contact the seller or manufacturer directly. Keep your purchase receipt for warranty claims.

A detailed user manual in PDF format is available for download: View User Manual (PDF)

© 2024 SUNON. All rights reserved.

Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.