1. Introduction
This manual provides detailed instructions for the installation, operation, and maintenance of your CENTURY AOKE APDC-4K 4-channel wireless remote control relay switch. Please read this manual carefully before use to ensure proper functionality and safety.
2. Package Contents
Depending on your purchased variant, your package may include:
- 1 x Receiver Module (AK-C211008)
- 1, 2, 3, or 4 x Transmitters (4-button yellow or industrial orange type)
- 1 x Antenna for Receiver

Figure 1: Typical package contents (Receiver, Antenna, and one Yellow Remote)

Figure 2: Package contents with industrial-style remotes
3. Setup
3.1 Transmitter Battery Installation
The transmitters require a 9V battery (not included) for the industrial type, or AA1.5V batteries for other types. Please ensure correct polarity when installing.
- Locate the battery compartment cover on the back of the transmitter.
- Slide or unscrew the cover to open the compartment.
- Insert the 9V battery, ensuring the positive (+) and negative (-) terminals align correctly.
- Replace the battery compartment cover.

Figure 3: Battery compartment on industrial remote

Figure 4: Installing a 9V battery
3.2 Receiver Wiring
The receiver module (AK-C211008) supports DC12V-36V input. Ensure the power supply matches the receiver's requirements. Connect the antenna to the SMA connector on the receiver board.

Figure 5: Receiver module overview
3.2.1 Output 12-36V Voltage Wiring Diagram
This diagram shows how to connect a load that requires 12-36V DC power, controlled by the receiver's relays.

Figure 6: Output 12-36V Voltage Wiring Diagram. Connect Input 12-36V to the '+' and '-' terminals. The output terminals provide switched 12-36V power.
3.2.2 Output Switch Signal Wiring Diagram
This diagram shows how to connect the receiver to control a device using a switch signal (e.g., for devices with their own power supply).

Figure 7: Output Switch Signal Wiring Diagram. Connect Input 12-36V to the '+' and '-' terminals. The output terminals act as dry contacts (NO/COM).
3.2.3 Wiring Diagram for DC Motor
This diagram illustrates how to connect two DC motors for directional control (e.g., forward/reverse) using two channels of the receiver.

Figure 8: Wiring Diagram for DC Motor. Connect Input 12-36V. Each motor (M) uses two output terminals for control.
4. Operating Instructions
4.1 Learning (Pairing) Method
This process pairs your transmitter with the receiver. The number of times you press the learning button determines the working mode.
- Locate the learning button on the receiver board.
- Press the learning button (1 to 6 times depending on desired mode, see Working Modes below). The indicator light on the receiver will flash and then turn OFF.
- Release your finger from the learning button.
- Within a few seconds, press any button on your remote transmitter.
- The indicator light on the receiver will flash three times, indicating successful learning.

Figure 9: Learning button and indicator light on receiver board
4.2 Clearing Method
This process clears all paired transmitters from the receiver's memory.
- Hold down the learning button on the receiver for approximately 8 seconds.
- The indicator light will flash several times and then turn OFF.
- After clearing, press any button on a remote; the relay should not respond, indicating successful code clearing.
4.3 Working Modes
The working mode is set during the learning process by the number of times the learning button is pressed.
- Momentary Mode (Press Learning Button 1 time):
Press and hold a transmitter button (e.g., A) → Receiver relay A turns ON.
Release the transmitter button A → Receiver relay A turns OFF.
(Same behavior for buttons B, C, D) - Toggle Mode (Press Learning Button 2 times):
Press a transmitter button (e.g., A) once → Receiver relay A turns ON.
Press the same transmitter button A again → Receiver relay A turns OFF.
(Same behavior for buttons B, C, D) - Latched Mode (Press Learning Button 3 times):
Press transmitter button A → Receiver relay A turns ON (and relays B, C, D turn OFF).
Press transmitter button B → Receiver relay B turns ON (and relays A, C, D turn OFF).
Press transmitter button C → Receiver relay C turns ON (and relays A, B, D turn OFF).
Press transmitter button D → Receiver relay D turns ON (and relays A, B, C turn OFF).
Note: In Latched mode, only one channel can be ON at a time. - 2-Channel Momentary + 2-Channel Latched (Press Learning Button 4 times)
- 2-Channel Momentary + 2-Channel Toggle (Press Learning Button 5 times)
- 2-Channel Toggle + 2-Channel Latched (Press Learning Button 6 times)
5. Maintenance
- Battery Replacement: Replace the transmitter battery when the remote range decreases or the indicator light dims.
- Receiver Care: Keep the receiver module in a dry, dust-free environment. Avoid exposure to extreme temperatures or moisture.
- Connection Check: Periodically check all wiring connections to ensure they are secure.
6. Troubleshooting
- Remote Not Responding:
- Check the transmitter battery. Replace if necessary.
- Ensure the receiver is powered on.
- Re-pair the transmitter with the receiver (Learning Method).
- Check for strong radio interference in the area. - Relay Not Activating:
- Verify the load is correctly wired to the receiver's output terminals.
- Ensure the load itself is functional and its power supply (if external) is active.
- Check the maximum load specifications; an overloaded relay may not activate or may be damaged. - Reduced Remote Range:
- Ensure the receiver's antenna is properly connected and extended.
- Replace the transmitter battery.
- Avoid physical obstructions (thick walls, metal structures) between the transmitter and receiver.
- Minimize radio interference from other devices.
7. Specifications
7.1 Receiver Module (AK-C211008)
- Working Voltage: DC12V-36V
- Current: Standby < 10mA, Working < 128mA
- Working Temperature: -10°C to +60°C
- Receiver Frequency: 315MHz / 433.92MHz (Please verify your specific model)
- Receiving Sensitivity: -105dB
- Output State: Switching Value (Dry Contact)
- Max Load: 10A Relay (Resistive load < 8A, Inductive load < 3A)
- Case Size: 96 x 80 x 29mm
- Encoding Type: Learning Code
7.2 Transmitter (Industrial Type)
- Buttons: 4 Buttons (1, 2, 3, 4)
- Working Voltage: 9V (Battery)
- Operating Frequency: 433MHz (or 315MHz, please verify)
- Remote Distance: 100-1000M (Ideal, line of sight)
- Operating Current: 13 mAh
- Encode: EV1527 code
- Dimensions: 150mm (L) x 50.7mm (W) x 26.5mm (D)

Figure 10: Industrial remote control dimensions
8. User Tips
- Verify Voltage: Always double-check the input voltage specification of the receiver you received (DC12-36V or AC100-240V) against your order to ensure compatibility and prevent damage.
- Test Range: Before final installation, test the remote control range in your intended environment to ensure it meets your operational needs.
9. Warranty and Support
For warranty information, please refer to the terms and conditions provided by your retailer at the time of purchase. For technical support or further assistance, please contact your seller or the product manufacturer.