1. Product Information
This manual provides instructions for the installation, maintenance, and safe use of your new motorcycle front mudguard fender extender.
- Product Name: Motorcycle Accessories Front Mudguard Fender Rear Extender Protection Extension
- Brand: Otilli
- Model: Front Mudguard Fender Extender for Aprilia Caponord 1200 Rally
- Fitment: Specifically designed for Aprilia Caponord 1200 Rally models from 2015 to 2017.
- Purpose: To provide additional protection to your motorcycle by extending the front fender, preventing debris from the front wheel from hitting the motorcycle body.
2. Safety & Warnings
Important Safety Information
Read all instructions carefully before use. Failure to follow these instructions may result in damage to the product or personal injury.
- Warning: Keep the device and its components out of reach of children under 3 years old.
- Keep away from children unless supervised by an adult during installation.
- Do not use this product for purposes other than its intended use as a motorcycle fender extender.
- Inspect the product before each use and installation; do not use if damaged.
- Follow all installation and operation guidelines to avoid injury.
- Do not expose the product to excessive water or moisture during storage or installation.
- Handle with care to avoid cuts or injuries from tools during installation.
3. Setup & Installation
Components Included:
- Front Mudguard Fender Extender (1 unit)
- Adhesive pads (pre-cut, red)
- Mounting screws/rivets
Figure 1: Fender extender kit components
Tools Recommended (Not Included):
- Drill (for rivet installation, if applicable)
- Appropriate drill bit size for rivets
- Cleaning solution (e.g., isopropyl alcohol) and clean cloth
- Marker or pencil (for marking drill points)
Installation Steps:
- Prepare the Surface: Thoroughly clean the area on your motorcycle's original front fender where the extender will be attached. Ensure it is free from dirt, grease, and wax. Allow the surface to dry completely.
- Test Fit: Carefully position the fender extender against your motorcycle's original front fender to ensure proper alignment and fit. Mark any necessary drill points if you plan to use rivets for a permanent connection.
- Apply Adhesive: Peel the backing from the provided adhesive pads and carefully apply them to the corresponding areas on the fender extender. Ensure good contact.
- Attach Extender: Align the fender extender with the original fender and firmly press it into place, ensuring the adhesive makes full contact. Apply pressure for a few minutes to secure the bond.
- Secure with Rivets (Optional but Recommended): For a more permanent and secure attachment, drill pilot holes through the extender and original fender at the marked points. Install the provided rivets according to standard riveting procedures.
Figure 2: Fender extender installed on a motorcycle
Figure 3: Side view of the installed fender extender
4. Operating Instructions
Once properly installed, the fender extender operates passively by providing extended coverage to your motorcycle's front fender. It is designed to:
- Reduce spray and debris from the front wheel hitting the engine, radiator, and other front components.
- Protect the motorcycle's bodywork from stone chips and road grime.
- Enhance the aesthetic appeal of your motorcycle.
5. Maintenance
- Cleaning: Clean the fender extender regularly with mild soap and water. Avoid abrasive cleaners or solvents that could damage the ABS plastic.
- Inspection: Periodically check the fender extender for any signs of damage, cracks, or loosening of the adhesive/rivets. Ensure it remains securely attached to the original fender.
- Damage: If the extender becomes damaged, consider replacing it to maintain optimal protection and appearance.
6. Troubleshooting
- Extender feels loose: If the extender begins to feel loose, re-check the adhesive bond and the security of any rivets. Reapply adhesive or replace rivets if necessary. Ensure the surface is clean before re-adhering.
- Improper fit: Double-check that the product is indeed for the Aprilia Caponord 1200 Rally 2015-2017 model. If the fit is still incorrect, contact the seller for assistance.
- Damage during installation: If the product is damaged during installation, assess if it affects functionality or safety. If so, it is recommended to replace the unit.
7. Specifications
| Attribute | Specification |
| Brand Name | Otilli |
| Material | High-impact resistant ABS Plastic |
| Color | Black |
| Fitment | For Aprilia Caponord 1200 Rally 2015 - 2017 |
| Item Weight | 0.2 kg |
| Condition | 100% Brand New |
| Quantity | 1 item |
Figure 4: High-quality ABS plastic material benefits
8. User Tips
No specific user tips were available from reviews or Q&A for this product. Always ensure a clean surface for adhesive application and consider using rivets for maximum security.
9. Warranty & Support
For any issues, questions, or support regarding your product, please contact the seller or manufacturer directly.
Manufacturer Information:
- Company: Guangzhou Otili Trading Co.,Ltd
- Address: CN-Nanhai District, Foshan City, Guangdong Province, Dali Town, Fengxiu Building, 9th Floor
- Tel: +86-13632806159
- Email: 243226686@qq.com
EU Authorized Representative:
- Name: SUCCESS COURIER SL
- Address: ES-CALLE RIO TORMES NUM. 1, PLANTA 1, DERECHA, OFICINA 3, Fuenlabrada, Madrid, 28947, Spain
- Tel: +34-910602659
- E-mail: successservice2@hotmail.com