Introduction
The Retekess TD112 Wireless Waiter Calling System is designed to enhance communication and service efficiency in various environments such as restaurants, cafes, bars, and clinics. This watch receiver is IPX7 waterproof, supports multiple languages, and offers various customizable settings for optimal performance.
Note: This watch receiver can only be used with Retekess brand call buttons, not with other brands of call buttons.
Video: Overview of the Retekess TD112 Wireless Staff Paging System, highlighting key features and applications.
Functional Diagram
Image: Functional diagram of the TD112 watch pager, showing the LED Display, A Button, B Button, and Charging/IO port (bottom).
- LED Display: Shows time, date, call information, battery status, and settings.
- A Button: Used for navigation and selection in menus, and continuous value increase in some settings.
- B Button: Used for navigation, moving edit positions, exiting menus, and saving settings.
- Charging/IO Port (bottom): Used for charging and connecting to PC for software operations.
Setup
Power On, Power Off, Wake Up, Call Confirmation and Delete
- Power On: In the off state, press the "B" button to turn on the watch. Upon first use or after a factory reset, you will be prompted to set the watch pager's name and ID.
- Power Off: In the standby state, press and hold the "B" button for about 3 seconds to turn it off.
- Wake Up: In sleep mode, press any key or receive an incoming call message to wake up the screen and enter working mode.
- Call Confirmation & Delete: In working mode, short press any key to confirm and delete the received call.
- Continuous Value Increase: In some settings, pressing and holding the "A" button can continuously increase the value.
Battery Instructions
The TD112 uses a special charging clip method. It takes approximately 3 hours for a full charge.
Image: The TD112 watch pager being charged with its clip-on charger, showing the 180mAh battery and 48-72 hour standby time.
- While charging in Standby State, the battery icon flashes.
- While charging in Off State, the power icon and battery icon flash.
- The battery icon stops flashing when fully charged.
- When the battery is low, the battery icon will flash on the screen.
Pairing Operation
The watch pager can pair with up to 500 call buttons.
Image: The TD112 watch pager shown working with various keypads and call buttons, illustrating its compatibility.
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Pairing".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
Ext Pair (Pairing with Call Buttons)
- Press "A" or "B" button to select "Ext Pair".
- Press and hold (approx. 1s) "A" button to enter sub-menu. It will show the ID number and ID status (e.g., Pair NO 0001).
- Press "B" button to move the edit position.
- Press "A" button to select the desired value (0-9, A-Z). Press and hold (approx. 1s) "A" button to delete the current paired ID.
- Press the call button that needs to be paired. The watch pager will vibrate and the status will change from "NO" to "OK". This completes the pairing. It will automatically go to the next ID for pairing a new call button.
- Press and hold (approx. 1s) "B" button twice to return to the setting menu after pairing all call buttons.
Key Pair (Pairing with Keypad)
- Press "A" or "B" button to select "Ket Pair".
- Press and hold (approx. 1s) "A" button to enter sub-menu. It shows the Pager ID, Keypad Serial Number, and status.
- Press "B" button to move the edit position.
- Press "A" button to select the desired value (Pager ID 001-999, Keypad Serial Number 01-50, "FFF" means not registered). Press and hold (approx. 1s) "A" button to delete the current paired ID.
- Press the corresponding Pager ID number on the keypad. The watch pager will vibrate and show OK on the display, and "FFF" will change to the Keypad ID.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Operating Instructions
General Operation
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select the desired value.
- Press "A" button for 1s to enter sub-menu.
- Press "B" button for 1s to exit and save the current function setting.
Delete Received Call Information
When the watch pager receives calls, the information is displayed in a loop (5s cycle, max 10 calls).
- Press and hold any key to delete all incoming calls and return to standby state.
- Press any key to delete the currently displayed call information.
Set Time
Image: The TD112 watch pager displaying time setting options, including clock setting, alarm setting, and ON/OFF time setting.
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Set Time".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select "Time".
- Press and hold (approx. 1s) "A" button to enter time setting (shows Hour and Minute, e.g., 13:12).
- Press "B" button to move the edit position among Hour, Minute, Year, Month, and Date.
- Press "A" button to select the desired value.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Alarm Setting (up to two alarms can be set)
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Set Time".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select "Alarm".
- Press and hold (approx. 1s) "A" button to enter Alarm Setting (shows alarm times).
- Press "B" button to move the edit position.
- Press "A" button to select the desired value.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Power T (Timer Switch Setting)
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Set Time".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select "Powr T".
- Press and hold (approx. 1s) "A" button to enter Timer Switch Setting (shows automatic switch times).
- Press "B" button to move the edit position.
- Press "A" button to select the desired value.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
NOTE:
The automatic shutdown function can only be performed in the standby state. When the automatic shutdown time is reached, the display will show "Auto Off", and the watch will vibrate twice to remind the user. The user can press any key to stop the automatic shutdown within 10 seconds.
Prompt Setting
Vibration Time
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Prompts".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select "Vibrate T".
- Press and hold (approx. 1s) "A" button to enter Vibration Time Setting (shows vibration status and prompt time, 1-15 seconds).
- Press "B" button to move the edit position.
- Press "A" button to select the desired value.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Display Time
Image: The TD112 watch pager illustrating two prompt methods: display only and vibration with display.
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Prompts".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select "Display T".
- Press and hold (approx. 1s) "A" button to enter Display Time Setting (shows display time on screen, 00-10 minutes, 00 means calls are never auto-cleared).
- Press "B" button to move the edit position.
- Press "A" button to select the desired value.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Note:
The storage time of the call information is the vibration time plus the display time.
Working Mode Setting
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Modes".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select the desired value.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Note:
There are 3 working modes available: General, Single Button, and Choose Receiver. General and Choose Receiver are compatible during pairing. If you change from General/Choose Receiver to Single Button mode, you need to re-pair.
- General: Pairs with keypad and multi-key callers.
- Single Button: Pairs any key from one multi-key caller with the watch pager. Each key from a multi-key caller can call a specific watch receiver, and key names received on the watch are the same.
- Choose Receiver: Allows setting the watch to receive calls from specific keys from one multi-key caller. Custom key names can be set using the "Key Set" instruction.
Key Set (Set the Key Name)
Image: The TD112 watch pager showing two methods for key name setting: directly on the watch or via computer software.
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Key Set".
- Press and hold (approx. 1s) "A" button to enter sub-menu. It shows the key name, serial number, and selection box.
- Press "A" or "B" button to select the desired value.
- Press the corresponding key from the call button to define the key name. The serial number will become the key value.
- If using Watch Pager Software for custom key names, press "A" and "B" buttons simultaneously to switch between custom and default key names.
- In "Choose R" working mode, press and hold (approx. 1s) "A" button to select or cancel the selection.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
NOTE:
Only one key name can be set per key. If no serial number is set for the key name, "FF" will be displayed. If the watch pager does not respond after pairing, set the key name via the above steps or through the Watch Pager Software. (When using PC software to custom key names, the cancel button needs to be edited as "CANCEL").
Language Setting
Image: The TD112 watch pager displaying flags of countries representing the 7 supported languages: English, Chinese, German, Spanish, Italian, French, and Portuguese.
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Language".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select the desired value (English, Chinese, Italian, Español, Deutsch, Français, and Português are available).
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Name ID Setting
Image: The TD112 watch pager displaying a call from "0003 Waiter", illustrating the customizable key name setting feature.
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Name ID".
- Press and hold (approx. 1s) "A" button to enter sub-menu. It shows the Name and ID on the screen.
- Press "B" button to move the edit position.
- Press "A" button to select the desired value (ID 001-999, Name A-Z, a-z, space, up to 10 characters).
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Note:
You will be reminded to set the watch pager's name and ID when the device is turned on for the first time or after a factory reset. Press and hold (approx. 1s) "B" button to exit the setting mode.
Maintenance
Restore Factory Setting
Clear Pairing
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Default".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select "Clear".
- Press and hold (approx. 1s) "A" button to clear the pairing data. "Clearing..." will show on the screen.
- Press and hold (approx. 1s) "B" button twice to exit the setting mode.
Reset
- In standby state, press and hold (approx. 1s) "A" button to enter setting mode.
- Press "A" or "B" button to select "Default".
- Press and hold (approx. 1s) "A" button to enter sub-menu.
- Press "A" or "B" button to select "Reset".
- Press and hold (approx. 1s) "A" button to enter reset setting. "Clearing..." will show on the screen. The watch pager will automatically restart after the factory reset is completed.
Troubleshooting
- Watch Pager not responding after pairing: If the watch pager does not respond when the call button is pressed after pairing, refer to the "Key Set" instructions to set the key name.
- Automatic Shutdown: If the watch pager automatically shuts down, press any key within 10 seconds of the "Auto Off" display and vibration reminder to stop it.
- PC Software Issues: When using the PC software to write data, the original data will be overwritten. Always export and save original data before making settings.
- Interference: If the device causes harmful interference, try reorienting the receiving antenna, increasing separation between equipment, or connecting to a different circuit.
Specifications
| Feature | Specification |
|---|---|
| Model Number | TD112 |
| Brand Name | Retekess |
| Frequency | AM 433MHz |
| Prompting Mode | Vibrate |
| Standby Time | 48~72 hours (actual time depends on working frequency) |
| Battery | Built-in 180mAh lithium battery |
| Waterproof Level | IPX7 |
| Remind Time | 1-15 seconds |
| Receiving Sensitivity | -114dBm |
| Size | 48*25*15 mm |
| Net Weight | 35g |
| Capacity | 450 call buttons + 50 keypads + 50 custom callers |
| Stored Call Information | 10 |
| Certification | CE, FCC |
Package Includes:
- 5 x Watch Receiver
- 5 x Micro-USB cable
- 5 x Power Adapter (EU/US/AU/UK optional)
Watch Pager PC Software
The Watch Pager PC Software allows users to change the watch pager's settings and manage call information more efficiently.
Image: The TD112 watch pager connected to a laptop via its charging clip, showing the PC software interface for setting and calling.
You can download the Watch Pager Software and Instruction from the Retekess official website: https://www.retekess.com/resources/download
General Operation
- Open the Watch Pager Software on your PC.
- Connect the watch pager (must be in standby state) to the PC using the charging cable.
- Perform relevant operations in the software.
- Press "Write" after editing the desired value.
NOTE:
- Original data will be overwritten when writing data. It is recommended to export and save original data before making settings.
- The "Caller ID" can be automatically obtained by pressing the corresponding button when the Watch Pager and Software are connected.
Extended Function (Page Watch Pager from PC)
Connect the Retekess USB transmitter (model: TD030) to the PC. The user can then page the watch pager via the Watch Pager Software. The TD030 USB transmitter needs to be purchased separately.
Image: The Retekess TD030 USB transmitter, used for paging the watch pager from a PC.
Safety Information and Warnings
RF Energy Exposure and Product Safety Guide
ATTENTION!
Before using this radio, read this guide which contains important operating instructions for safe usage and RF energy awareness and control for compliance with applicable standards and regulations.
This radio uses electromagnetic energy (RF) for communication. Improper use of RF energy can cause biological damage. All Retekess radios are designed, manufactured, and tested to meet government-established RF exposure levels. Manufacturers recommend specific operating instructions to users. These instructions inform users about RF energy exposure and provide simple control procedures.
For more information on RF energy exposure and compliance, refer to: http://www.who.int/en/
Local Government Regulations
When radios are used for employment, users must be fully aware of and able to control their exposure to meet occupational requirements. Product labels provide specific user awareness information. Your Retekess radio has an RF Exposure Product Label. The user manual and separate safety booklet contain information and operating instructions to control RF exposure and satisfy compliance requirements.
Radio License (if appropriate)
Business radios operate on regulated frequencies. To transmit on these frequencies, a license may be required. Contact local government radio management departments for detailed classification and usage. Use of this radio outside its intended country of distribution may be prohibited.
Unauthorized Modification and Adjustment
Changes or modifications not expressly approved by the party responsible for compliance may void the user's authority to operate this radio. Transmitter adjustments should only be made by or under the supervision of a technically qualified person. Replacement of any unauthorized transmitter components (crystal, semiconductor, etc.) could violate rules.
FCC Requirements:
- This device complies with part 15 of the FCC Rules. Operation is subject to two conditions:
- This device may not cause harmful interference.
- This device must accept any interference received, including interference that may cause undesired operation.
- This equipment has been tested and found to comply with limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.
- This equipment generates, uses, and can radiate radio frequency energy. If not installed and used according to instructions, it may cause harmful interference to radio communications. There is no guarantee that interference will not occur in a particular installation. If this equipment causes harmful interference to radio or television reception, try to correct it by:
- Reorienting or relocating the receiving antenna.
- Increasing the separation between the equipment and receiver.
- Connecting the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consulting the dealer or an experienced radio/TV technician for help.
CE Requirements:
Henan Eshow Electronic Commerce Co., Ltd declares that the radio equipment type is in compliance with the essential requirements and other relevant provisions of RED Directive 2014/53/EU and the ROHS Directive 2011/65/EU and the WEEE Directive 2012/19/EU. The full text of the EU declaration of conformity is available at: www.retekess.com.
Avoid Choking Hazard
Small Parts. Not for children under 3 years.

Protect Your Hearing
WARNING!
- Use the lowest volume necessary for your job.
- Turn up the volume only if you are in noisy surroundings.
- Turn down the volume before adding headset or earpiece.
- Limit the amount of time you use headsets or earpieces at high volume.
- When using the radio without a headset or earpiece, do not place the radio's speaker directly against your ear.
- Use careful with the earphone, excessive sound pressure from earphones and headphones can cause hearing loss.
Note: Exposure to loud noises from any source for extended periods of time may temporarily or permanently affect your hearing. The louder the radio's volume, the less time is required before your hearing could be affected. Hearing damage from loud noise is sometimes undetectable at first and can have a cumulative effect.
Avoid Burns
Antennas
WARNING!
Do not use any portable radio that has a damaged antenna. If a damaged antenna comes into contact with the skin when the radio is in use, a minor burn can result.
Batteries
WARNING!
When conductive material such as jewelry, keys, or chains touch exposed terminals of the batteries, it may complete an electrical circuit (short circuit the battery) and become hot, causing bodily injury or burns. Exercise care in handling any battery, especially when placing it inside a pocket, purse, or other container with metal objects.
Long Transmission
When the transceiver is used for long transmissions, the radiator and chassis will become hot.
Safety Operation
Forbid
WARNING!
- Do not use charger outdoors or in moist environments; use only in dry locations/conditions.
- Do not disassemble the charger; this may result in risk of electrical shock or fire.
- Do not operate the charger if it has been broken or damaged in any way.
- Do not place a portable radio in the area over an airbag or in the airbag deployment area. The radio can be propelled with great force and cause serious injury to occupants of the vehicle when the airbag inflates.
To Reduce Risk
- Pull by the plug rather than the cord when disconnecting the charger.
- Unplug the charger from the AC outlet before attempting any maintenance or cleaning.
- Contact Retekess for assistance regarding repairs and service.
- The adapter shall be installed near the equipment and shall be easily accessible.
- Risk of explosion if battery is replaced by an incorrect type. Dispose of used batteries according to the instructions.
- The plug is considered the disconnect device of the adapter.
- The operating temperature of the EUT cannot exceed the specified range.
Approved Accessories
WARNING!
This radio meets RF exposure guidelines when used with Retekess accessories supplied or designated for the product. Use of other accessories may not ensure compliance with RF exposure guidelines and may violate regulations.
For a list of Retekess-approved accessories for your radio model, visit: http://www.retekess.com
Warranty and Support
Most new products carry a two-year manufacturer's warranty from the date of purchase.
For warranty and after-sales service:
- Contact the seller where you purchased the product.
- Products can be repaired by our Local Repair Center.
- For warranty service, you will need to provide a receipt or proof of purchase from the actual seller for verification.
Exclusions from Warranty Coverage:
- Any product damaged by accident.
- Misuse or abuse of the product, or damage resulting from unauthorized alterations or repairs.
- If the serial number has been altered, defaced, or removed.
EU Importer:
Name: Germany Retevis Technology GmbH
Address: Uetzenacker 29, 38176 Wendeburg
Contact Information:
Web: www.retekess.com
Email: support@retekess.com
The full user manual in PDF format can be viewed at: TD112 User Manual (PDF)
User Tips
- For advanced customization of key names and other settings, utilize the PC software. Remember to save your original settings before making changes.
- The IPX7 waterproof rating allows for hand washing and exposure to splashes, but avoid prolonged submersion or high-pressure water.
- Take advantage of the multiple language options to ensure clear communication for all staff members.
- Use the timer switch setting to conserve battery life during off-peak hours.