HLTNC A1-SVD-15A, AASD-15A, A1-SVD-20A, AASD-20A, A1-SVD-30A, AASD-30A, AASD-50A

Contents

HLTNC AC Servo Motor Driver User Manual

Models: A1-SVD-15A, AASD-15A, A1-SVD-20A, AASD-20A, A1-SVD-30A, AASD-30A, AASD-50A

1. Introduction

This manual provides essential information for the safe and efficient operation of your HLTNC AC Servo Motor Driver. These drivers are designed for high-performance applications, particularly in CNC machines, offering stable performance, fast response, and advanced heat dissipation.

HLTNC (Lishui Hengli Automation Technology Co., Ltd.) specializes in R&D and production of linear motion units and various electrical products including stepper motors, servo motors, reduction motors, closed-loop motors, spindle motors, and frequency converters. Our products are known for their quality and affordability.

The AASD series generally offers better performance and stability compared to the A1-SVD series.

HLTNC AC Servo Motor Driver front view

Figure 1.1: Front view of the HLTNC AC Servo Motor Driver.

2. Safety Instructions

Please read and understand all safety warnings and instructions before installing, operating, or maintaining the servo motor driver. Failure to comply may result in personal injury or equipment damage.

  • Electrical Hazard: This device operates with high voltage. Ensure power is disconnected before any installation or maintenance work. Only qualified personnel should perform electrical connections.
  • Braking Resistor Connection: When connecting an external braking resistor, ensure its selection and power rating are appropriate to avoid burning out the driver, as it operates in parallel with the internal braking circuit.
  • Proper Grounding: Always ensure the driver is properly grounded to prevent electrical shock and ensure stable operation.
  • Signal Integrity: To ensure good signal quality, especially for encoder differential signals, use twisted-pair cables. Connect shielding to the shield wire's FG terminal.
  • Environment: Install the driver in a clean, dry, and well-ventilated area, away from direct sunlight, excessive vibration, and corrosive gases.

3. Product Overview

3.1 Key Features

  • Stable performance and fast response.
  • Advanced heat dissipation design, often including a cooling fan (15A drivers may not have a fan).
  • High cost-performance ratio.
  • Integrated control for speed, position, and torque.
  • Supports various encoder types (incremental, absolute, resolver).
  • Multiple communication interfaces (RS485, CAN).

3.2 Dimensions

Typical dimensions for the servo motor driver are approximately 190mm (length) x 160mm (width) x 50mm (height).

Servo motor driver dimensions diagram

Figure 3.1: Approximate dimensions of the servo motor driver.

3.3 Component Identification

Refer to the diagram below for identification of the main interfaces and terminals:

Labeled diagram of servo motor driver connection interfaces

Figure 3.2: Main connection interfaces.

  1. Communication Interface
  2. PC signal input
  3. Encoder signal input
  4. Control circuit power supply
  5. Main circuit power supply
  6. External braking resistor interface
  7. Motor power line
  8. Ground terminal

4. Setup and Installation

4.1 General Wiring Diagram

The following diagram illustrates a typical wiring setup for the servo motor driver with a host computer and servo motor.

General wiring diagram for HLTNC servo motor driver

Figure 4.1: General wiring diagram.

4.2 Terminal Definitions and Connections

Detailed terminal definitions for various series (TH-S3a, TH-T3a/T3L, TH-T3M/T3G, TH-T5M/T5a, TH-G) are provided in the comprehensive PDF manual. Below are general connection guidelines:

Terminal Group Terminals Description
Main Circuit Power R, S, T Connect to external AC power supply (Three-phase 220V or Single-phase 220V, 50/60Hz).
Braking Resistor P, BK Connect external braking resistor. Ensure proper selection and power rating.
Motor Connection U, V, W Output to servo motor power supply.
Ground Terminal PE Driver grounding terminal.
Control Circuit Power DC24V Connect to 24V DC power supply.
Communication Interface CN1, CN2, CN3 Connect to PC or other control systems for signal input/output and communication. Refer to PDF manual for pinouts.
Encoder Signal Input CN2 Connect to servo motor encoder. Use twisted-pair cables for differential signals.

5. Operating Instructions

5.1 Control Panel

The driver features a 5-digit LED display and several buttons for configuration and monitoring.

Control panel display and buttons

Figure 5.1: Control panel layout.

5.2 Button Functions

Button Button Name Features
MODE Mode Selection Key
  • Mode switching
  • Return to the upper-level directory
Up arrow icon Number Increase Key Increase the number; long press has a repeating effect.
Down arrow icon Decrease Key Decrease the number; long press has a repeating effect.
Shift Shift Key Cursor Shift
SET OK Key
  • Confirm the settings
  • End parameter setting

Note: If all 5 decimal points on the display screen are flashing, it indicates an alarm is generated. The alarm must be cleared before the driver can operate normally.

6. Specifications

The HLTNC AC Servo Motor Drivers are available in various models with different current and power ratings. All models operate on 220V AC power supply.

Table of specifications for AASD and A1-SVD models

Figure 6.1: Model-specific electrical specifications.

Model Current (A) Voltage (V) Application for Servo Motor (KW)
AASD-15A 15A 220V 0.4-0.75KW
AASD-20A 20A 220V 1KW
AASD-30A 30A 220V 1.2-2.6KW
AASD-50A 50A 220V 3.5KW
A1-SVD15 15A 220V 0.4-0.75KW
A1-SVD20 20A 220V 1KW
A1-SVD30 30A 220V 1.2-2.6KW

General Specifications:

  • Brand Name: HLTNC
  • Power Supply: AC
  • Motor Type: AC Motor
  • Origin: Mainland China
  • Certification: CE
  • High-concerned chemical: None

7. Troubleshooting

If the driver encounters an issue, it may display an alarm. The primary alarm indication is when all 5 decimal points on the display screen are flashing.

  • Alarm Indication: All 5 decimal points flashing on the display.
  • Action: Clear the alarm before attempting to operate the driver normally.
  • Common Issues:
    • No Power: Check main circuit power supply (R, S, T) and control circuit power supply (DC24V).
    • Motor Not Responding: Verify motor power lines (U, V, W) and encoder connections (CN2).
    • Communication Errors: Check connections to CN1, CN2, CN3 and ensure correct communication parameters.
    • Overload/Overcurrent: Reduce load or check for motor/mechanical issues.

For detailed error codes, diagnostic procedures, and advanced troubleshooting, please refer to the official user manual PDF: View User Manual (PDF).

8. Maintenance

Regular maintenance ensures the longevity and optimal performance of your servo motor driver.

  • Keep Clean: Regularly clean the exterior of the driver to prevent dust and debris buildup, especially around cooling fins and fans.
  • Check Connections: Periodically inspect all wiring connections for tightness and signs of wear or corrosion.
  • Ensure Ventilation: Make sure the installation environment provides adequate airflow to prevent overheating. Keep ventilation openings clear.
  • Environmental Conditions: Operate the driver within specified temperature and humidity ranges.

9. User Tips

  • Parameter Tuning: For optimal performance, fine-tune the servo parameters according to your specific motor and mechanical load characteristics. Refer to the detailed PDF manual for parameter settings.
  • Cable Management: Use high-quality shielded cables for power and signal connections to minimize electrical noise and interference. Proper cable routing can prevent signal degradation.
  • Software Configuration: Utilize the provided PC software (if applicable) for advanced configuration, monitoring, and diagnostics.

10. Support and Contact Information

For technical inquiries, support, or further assistance, please contact HLTNC:

  • Company Website: https://www.hitcnc.com/
  • Technical Inquiry Phone: 13059655753
  • General Phone: 0578-2520261 / 2136580
  • Email: 66027708@163.com
  • Address: No. 83, Yunjing Road, Liandu District, Lishui, Zhejiang, Mainland China
Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.