Introduction
The Dooya DM45R is a versatile radio tubular motor designed for various applications such as rolling blinds, canopies, and lift systems. This motor operates on AC power (220/230V 50/60Hz or 120V 60Hz, depending on the model) and features an integrated RF433 receiver for remote control operation. This manual provides detailed instructions for installation, wiring, programming, and setting the operational limits of your DM45R motor.
Before proceeding with installation, please ensure you have the correct crown and driving components that match your specific tube type. Remote controllers are sold separately and are required for operation.
Specifications
The Dooya DM45R series offers various models with different torque and speed ratings. Below is a detailed table of technical data for common 230V/50Hz and 120V/60Hz models.
General Specifications
- Model Number: DM45R
- Voltage: 230V (EU LVD: Below 50Vac or 75Vdc)
- Wattage: 220/230V 50/60HZ
- is_customized: Yes
- Rolling Speed: None (variable by model)
- Origin: Mainland China
- Certification: NONE
- High-concerned chemical: None
- Battery Included: No
- Work with: Dooya 433mhz remote controller
Technical Data (230V / 50Hz)
| Model | Rated Torque (Nm) | Rated Speed (r/min) | Diameter (mm) | Voltage (V) | Frequency (Hz) | Rated Power (W) | Rated Current (A) | Weight (kg) | Capacitor (uF/V) | IP Rating | Insulation Class | Tube Size (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DM45R - 10/15 | 10 | 15 | 45 | 230 | 50/60 | 145 | 0.64 | 2.15 | 5/450 | IP44 | H | 45 |
| DM45R - 20/15 | 20 | 15 | 45 | 230 | 50/60 | 145 | 0.64 | 2.15 | 5/450 | IP44 | H | 45 |
| DM45R - 30/15 | 30 | 15 | 45 | 230 | 50/60 | 191 | 0.83 | 2.15 | 5/450 | IP44 | H | 45 |
| DM45R - 40/15 | 40 | 15 | 45 | 230 | 50/60 | 198 | 0.86 | 2.15 | 5/450 | IP44 | H | 45 |
| DM45R - 50/12 | 50 | 12 | 45 | 230 | 50/60 | 205 | 0.89 | 2.15 | 5/450 | IP44 | H | 45 |
| DM45R - 60/8 | 60 | 8 | 45 | 230 | 50/60 | 208 | 0.92 | 2.15 | 5/450 | IP44 | H | 45 |
Technical Data (120V / 60Hz)
| Model | Rated Torque (Nm) | Rated Speed (r/min) | Diameter (mm) | Voltage (V) | Frequency (Hz) | Rated Power (W) | Rated Current (A) | Weight (kg) | Capacitor (uF/V) | IP Rating | Insulation Class | Tube Size (mm) |
|---|---|---|---|---|---|---|---|---|---|---|---|---|
| DM45R - 10/19 | 10 | 19 | 45 | 120 | 60 | 136 | 1.17 | 2.15 | 4/450 | IP44 | H | 45 |
| DM45R - 10/32 | 10 | 32 | 45 | 120 | 60 | 140 | 1.20 | 2.15 | 4/450 | IP44 | H | 45 |
| DM45R - 20/19 | 20 | 19 | 45 | 120 | 60 | 162 | 1.54 | 2.15 | 4/450 | IP44 | H | 45 |
| DM45R - 20/32 | 20 | 32 | 45 | 120 | 60 | 160 | 1.59 | 2.15 | 4/450 | IP44 | H | 45 |
| DM45R - 30/13 | 30 | 13 | 45 | 120 | 60 | 152 | 1.51 | 2.15 | 4/450 | IP44 | H | 45 |
| DM45R - 40/13 | 40 | 13 | 45 | 120 | 60 | 166 | 1.48 | 2.15 | 4/450 | IP44 | H | 45 |
| DM45R - 50/13 | 50 | 13 | 45 | 120 | 60 | 235 | 2.20 | 2.15 | 4/450 | IP44 | H | 45 |
Package Contents
The standard package for the Dooya DM45R Tubular Motor typically includes:
- Dooya DM45R Tubular Motor
- Crown (specific to tube type)
- Driving component (specific to tube type)
Note: Additional accessories such as remote controllers, brackets, and idler sets are usually sold separately. Please ensure you purchase all necessary components for your specific installation.


Installation
Before starting, ensure the power supply is switched off. The DM45R motor is compatible with various tube types. Please verify your tube type and ensure you have the correct crown and driving components.

1. Crown Installation
- Slide the crown onto the motor shaft.
- Slide the driving component onto the motor shaft, ensuring it aligns with the crown.
- Secure the crown and driving. Important: Do not drill through the crown and inner gear wheel.
2. Drive Adapter Installation
- Insert the motor with the crown and driving into the tube.
- Align the drive adapter with the end of the tube.
- Secure the drive adapter to the tube using rivets or screws.
- Ensure the motor is properly seated within the tube and the drive adapter is firmly attached.
3. Bracket Installation
- Mount the brackets to the desired location, ensuring they are level and securely fastened.
- Insert the motor assembly into the mounted brackets. Ensure the motor is properly supported and can rotate freely.
Wiring (Circuit Installation)
WARNING: Ensure the main power supply is switched off before performing any wiring. Incorrect wiring can cause damage to the motor or pose a safety hazard. Refer to the product nameplate for specific voltage and frequency requirements (230V/50Hz or 120V/60Hz).

Wiring Diagram
Connect the motor to the AC power supply according to the following color codes:
- For 230V/50Hz (3x1.5mm²):
- Blue wire: Neutral
- Brown wire: Direction (Live)
- Green/Yellow wire: Earth
- For 120V/60Hz (3x18AWG):
- White wire: Neutral
- Black wire: Direction (Live)
- Green wire: Earth
Ensure all connections are secure and insulated. After wiring, switch on the power supply.
Programming the First Transmitter
This section describes how to pair your remote control with the motor. Remote controllers are sold separately.

Method 1: For a new motor or after factory reset
- Switch off the power to the motor.
- Switch on the power. The interval of re-switching on must be over 10 seconds.
- Within 4 seconds of switching on, press the P2 button on the remote control twice continuously. The motor will beep twice.
- Press the UP button on the remote control. The motor will beep several times.
- The motor is now programmed. The UP button controls the motor clockwise.
Method 2: If the motor has existing data (e.g., adding a new remote)
- Switch off the power to the motor.
- Switch on the power. The interval of re-switching on must be over 10 seconds.
- Within 4 seconds of switching on, press the P2 button on the remote control twice continuously. The motor will beep twice.
- Press the DOWN button on the remote control. The motor will beep several times.
- The motor is now programmed. The DOWN button controls the motor counter-clockwise.
Note: The interval between each button press during programming must be within 4 seconds, otherwise the system will revert to its original state.
Limit Setting
Setting the upper and lower limits defines the motor's travel range. Use the special regulator to adjust the limits. Do not adjust the red and white limit screws when the tubular motor is stopped.
1. Up Limit Setting
- Switch on the power.
- Press the UP button once.
- Use the special regulator to adjust the '+' direction. Rotate the white worm to increase the up distance.
- When the up limit distance reaches the desired location, stop rotating the white worm and press the STOP button on the remote.
- The up limit is now set.
2. Down Limit Setting
- Switch on the power.
- Press the DOWN button once.
- Use the special regulator to adjust the '+' direction. Rotate the red worm to increase the down distance.
- When the down limit distance reaches the desired location, stop rotating the red worm and press the STOP button on the remote.
- The down limit is now set.
Caution: If the motor does not work, stop rotating the red or white worm with the regulator.
Operating Instructions
Once the motor is installed, wired, and programmed, you can operate it using the paired Dooya 433MHz remote controller.
- UP Button: Activates the motor to move the blind/canopy upwards until it reaches the set upper limit or the button is released.
- DOWN Button: Activates the motor to move the blind/canopy downwards until it reaches the set lower limit or the button is released.
- STOP Button: Halts the motor's movement at any point.
Refer to your specific remote controller's manual for additional functions or advanced programming options (e.g., multi-channel control).

Maintenance
The Dooya DM45R tubular motor is designed for low maintenance. Follow these general guidelines to ensure longevity and optimal performance:
- Cleaning: Keep the motor and surrounding area free from dust and debris. Use a soft, dry cloth for cleaning. Do not use harsh chemicals or abrasive materials.
- Inspection: Periodically check the wiring for any signs of wear or damage. Ensure all mounting brackets and fasteners are secure.
- Obstructions: Ensure there are no obstructions in the path of the blind or canopy that could impede the motor's movement.
- Professional Service: For any internal issues or complex repairs, contact a qualified technician. Do not attempt to open or repair the motor yourself, as this may void the warranty and could be dangerous.
Troubleshooting
If you encounter issues with your DM45R motor, try the following troubleshooting steps:
- Motor Not Responding:
- Check if the power supply is on and properly connected.
- Ensure the remote control batteries are not depleted.
- Verify that the remote control is paired correctly with the motor (refer to Programming section).
- Motor Stops Mid-Operation:
- Check for any physical obstructions preventing the blind/canopy from moving.
- The motor may have overheated. Allow it to cool down for a few minutes before attempting operation again.
- Limits Not Working Correctly:
- Re-set the upper and lower limits (refer to Limit Setting section).
- Ensure the limit adjustment screws (red and white worms) are not tampered with while the motor is stopped.
- Unusual Noises:
- Inspect the tube and motor for any loose parts or foreign objects.
- If the noise persists, discontinue use and contact support.
If these steps do not resolve the issue, please contact customer support for further assistance.
User Tips
- Model Compatibility: When selecting a DM45R motor, always verify the specific model number (e.g., DM45R 40/13) to ensure it matches your required voltage (e.g., 120V) and frequency (e.g., 60Hz) for optimal performance and safety.
- Remote Controller Purchase: Remember that remote controllers are typically sold separately from the motor. Ensure you purchase a compatible Dooya 433MHz remote control for your motor.
- Tube Matching: Before purchasing, confirm the type of tube you will be using (e.g., grooved, round, specific diameter) so that the correct crown and driving components can be matched with your motor.
Frequently Asked Questions (FAQ)
- Q: Is the DM45R motor compatible with 120V 60Hz power supplies?
- A: Yes, specific models of the DM45R, such as the DM45R 40/13, are designed for 120V 60Hz operation. Please refer to the 'Specifications' section and your product's nameplate to confirm compatibility.
- Q: Does the motor come with a remote control?
- A: No, remote controllers for the Dooya DM45R motor are typically sold separately. You will need to purchase a compatible Dooya 433MHz remote control to operate the motor.
Warranty and Support
The Dooya DM45R Tubular Motor comes with a 1-year manufacturer's limited warranty for defective items, excluding items damaged or misused after receipt. Accessories typically come with a 3-month warranty.
Defective items must be reported and returned within the warranty period, preferably in their original packaging. Please provide your order number and a description of the defect when reporting an issue.
For technical support, troubleshooting assistance, or warranty claims, please contact your seller or the manufacturer directly. You may also find additional resources and a user manual in PDF format by viewing the 'Item guides & documents' section on the product page.