1. Introduction
1.1 About this Manual
This Manual is applicable to Network Video Recorder (NVR). The Manual includes instructions for using and managing the product. Pictures, charts, images and all other information hereinafter are for description and explanation only. The information contained in the Manual is subject to change, without notice, due to firmware updates or other reasons. Please find the latest version on the company website. Please use this user manual under the guidance of professionals.
1.2 Legal Disclaimer
REGARDING TO THE PRODUCT WITH INTERNET ACCESS, THE USE OF PRODUCT SHALL BE WHOLLY AT YOUR OWN RISKS. OUR COMPANY SHALL NOT TAKE ANY RESPONSIBILITIES FOR ABNORMAL OPERATION, PRIVACY LEAKAGE OR OTHER DAMAGES RESULTING FROM CYBER ATTACK, HACKER ATTACK, VIRUS INSPECTION, OR OTHER INTERNET SECURITY RISKS; HOWEVER, OUR COMPANY WILL PROVIDE TIMELY TECHNICAL SUPPORT IF REQUIRED. SURVEILLANCE LAWS VARY BY JURISDICTION. PLEASE CHECK ALL RELEVANT LAWS IN YOUR JURISDICTION BEFORE USING THIS PRODUCT IN ORDER TO ENSURE THAT YOUR USE CONFORMS THE APPLICABLE LAW. OUR COMPANY SHALL NOT BE LIABLE IN THE EVENT THAT THIS PRODUCT IS USED WITH ILLEGITIMATE PURPOSES. IN THE EVENT OF ANY CONFLICTS BETWEEN THIS MANUAL AND THE APPLICABLE LAW, THE LATER PREVAILS.
1.3 Regulatory Information
FCC Information
Please take attention that changes or modification are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment.
FCC Compliance: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Conditions: This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference. 2. This device must accept any interference received, including interference that may cause undesired operation.
EU Conformity Statement
This product and -if applicable -the supplied accessories too are marked with "CE" and comply therefore with the applicable harmonized European standards listed under the EMC Directive 2014/30/EU, the LVD Directive 2014/35/EU, the RoHS Directive 2011/65/EU.
2006/66/EC (battery directive): This product contains a battery that cannot be disposed of as unsorted municipal waste in the European Union. See the product documentation for specific battery information. The battery is marked with this symbol, which may include lettering to indicate cadmium (Cd), lead (Pb), or mercury (Hg). For proper recycling, return the battery to your supplier or to a designated collection point. For more information see: www.recyclethis.info
2. Safety Information
2.1 Safety Instruction
These instructions are intended to ensure that user can use the product correctly to avoid danger or property loss. The precaution measure is divided into [Warnings] and [Cautions].
Warnings: Serious injury or death may occur if any of the warnings are neglected.
Cautions: Injury or equipment damage may occur if any of the cautions are neglected.
| Warnings | Cautions | |
|---|---|---|
| Follow these safeguards to prevent serious injury or death. | Follow these precautions to prevent potential injury or material damage. |
2.2 General Warnings
- Proper configuration of all passwords and other security settings is the responsibility of the installer and/or end-user.
- In the use of the product, you must be in strict compliance with the electrical safety regulations of the nation and region. Please refer to technical specifications for detailed information.
- Input voltage should meet both the SELV (Safety Extra Low Voltage) and the Limited Power Source with 100 to 240 VAC or 12 VDC according to the IEC60950-1 standard. Please refer to technical specifications for detailed information.
- Do not connect several devices to one power adapter as adapter overload may cause over-heating or a fire hazard.
- Please make sure that the plug is firmly connected to the power socket.
- If smoke, odor or noise rise from the device, turn off the power at once and unplug the power cable, and then please contact the service center.
2.3 Preventive and Cautionary Tips
- Before connecting and operating your device, please be advised of the following tips:
- Ensure unit is installed in a well-ventilated, dust-free environment.
- Unit is designed for indoor use only. Keep all liquids away from the device.
- Ensure environmental conditions meet factory specifications.
- Ensure unit is properly secured to a rack or shelf. Major shocks or jolts to the unit as a result of dropping it may cause damage to the sensitive electronics within the unit.
- Use the device in conjunction with an UPS if possible.
- Power down the unit before connecting and disconnecting accessories and peripherals.
- A factory recommended HDD should be used for this device.
- Improper use or replacement of the battery may result in hazard of explosion. Replace with the same or equivalent type only. Dispose of used batteries according to the instructions provided by the battery manufacturer.
3. Setup Guide
3.1 What's in the Box
The package includes the following items:
- 1 x 32-Channel 4MP DVR
- 1 x DVR Power Adapter
- 1 x HDMI Cable
- 1 x USB Mouse
- 1 x Network Cable
- 1 x User's Manual
- 1 x Wall Sticker

3.2 Front Panel
The front panel of the NVR features various indicators and control buttons:

| No. | Name | Description |
|---|---|---|
| Power | Power indicator turns yellow when system is running. | |
| 1 | Status Indicator (Status) | Status indicator blinks red when data is being read from or written to HDD. |
| Status Indicator (Tx/Rx) | Tx/Rx indicator blinks yellow when network connection is functioning properly. | |
| 2 | USB Interface | Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). |
| 3 | Control Buttons (DIRECTION) | In menu mode, the direction buttons are used to navigate between different fields and items and select setting parameters. In playback mode, the Up and Down buttons are used to speed up and slow down record playing, and the Left and Right buttons are used to move the recording 30s forwards or backwards. In the image setting interface, the up and down button can adjust the level bar of the image parameters. In live view mode, these buttons can be used to switch channels. |
| Control Buttons (ENTER) | The Enter button is used to confirm selection in menu mode; or used to check check box fields and ON/OFF switch. In playback mode, it can be used to play or pause the video. In single-frame play mode, pressing the Enter button will play the video by a single frame. In auto sequence view mode, the buttons can be used to pause or resume auto sequence. | |
| 4 | MENU | Press the button will help you return to the Main menu (after successful login). In Playback mode, it is used to show/hide the control interface. |
| 5 | ESC | Back to the previous menu. Press for Arming/disarming the device in Live View mode. |
3.3 Rear Panel
The rear panel connections are crucial for setting up your NVR:

| No. | Item | Description |
|---|---|---|
| 1 | Power Supply | 48V DC power supply or AC 100~240V |
| 2 | Audio In | RCA connector for audio input. |
| 3 | HDMI Interface | HDMI video output connector. |
| 4 | LAN Network Interface | 1 10/100/1000 Mbps self-adaptive Ethernet interface |
| 5 | Audio Out | RCA connector for audio output. |
| 6 | VGA Interface | DB15 connector for VGA output. Display local video output and menu. |
| 7 | USB Interface | Universal Serial Bus (USB) ports for additional devices such as USB mouse and USB Hard Disk Drive (HDD). |
| 8 | Ground | Ground (needs to be connected when NVR starts up). |
| 9 | Power Switch | Switch for turning on/off the device. |
| 10 | Network Interfaces with PoE function | Network interfaces for the cameras and to provide power over Ethernet. |
3.4 Hard Disk Installation
After the hard disk is installed, the NVR can perform functions such as recording and playback. Without the HDD, you can only preview the current live monitoring video.
Note: Before installing a hard disk drive (HDD), please make sure the power is disconnected from the NVR. A factory recommended HDD should be used for this installation. One or two SATA hard disks can be installed depending on different models.
Tools Required: Screwdriver.
Steps:
- Remove the cover from the NVR by unfastening the screws on the back and side.

- Find out the power cable and data cable of the hard disk from the NVR accessories box, and prepare a hard disk and the hard disk screw. The three-color power cable is on the left and the blue data cable is on the right.

- Connect one end of the power cable to the motherboard of NVR.

- Connect one end of the data cable to the motherboard of NVR.

- Connect the data cable and the power cable to the HDD.

- Place the HDD on the bottom of the device and then fasten the screws on the bottom to fix the HDD.

- Re-install the cover of the NVR and fasten screws.
3.5 NVR Installation
Follow these steps to connect your NVR system:

- Connect the monitor's VGA cable or HDMI cable to the NVR's VGA cable or HDMI port.
- Connect the camera by network cable to the NVR's POE port.
- Connect the mouse to the NVR's USB port.
- Connect the NVR's RJ-45 port to the router's LAN by network cable.
- Connect the NVR's power adapter.
4. Operation
4.1 Activating Your Device
For the first-time access, you need to activate the device by setting an admin password. No operation is allowed before activation. You can also activate the device via Web Browser, SADP or Client Software.
Steps:
- Input the same password in the text field of Create New Password, Confirm New Password and IP Camera Activation Password. (You can set the IP camera activation password by yourself, but it is advisable to set the same one as the NVR's.)
Note: Please set a memorable password for easy use and keep well.

Strong Password recommended: We highly recommend you create a strong password of your own choosing (using a minimum of 8 characters, including upper case letters, lower case letters, numbers, and special characters) in order to increase the security of your product. And we recommend you reset your password regularly, especially in the high security system, resetting the password monthly or weekly can better protect your product.
- Click OK to save the password and then enter the Security Question Configuration interface.
- Select three security questions and enter your answers. It is advisable to take a picture of these questions and answers, so that you may need them to reset the password. Click "OK" and you will be prompted to activate the device.
- A prompt box will pop up, reminding you to export the GUID file for password resetting. This is another way to retrieve the password. Click "Yes" if you need backup. It is advisable to use a USB flash drive for the backup.
4.2 Setting Unlock Pattern
After activating your device, you can set an unlock pattern instead of typing the password. Draw the unlock pattern twice to confirm.

Then you can choose the system language you need.
4.3 Using the Setup Wizard
After setting the language, you will come to the setup wizard interface. The Setup Wizard can walk you through some important settings of the device.
- Click Next to continue the setup wizard and enter the signal input configuration interface.
- Configure the IP Address. If you want to monitor remotely, you need to connect your DVR to the Internet first, and the IP address and DNS server must be correctly obtained.
- Set the P2P function. You need to manually enter a verification code first, which consists of 6 to 12 digits or letters, and then confirm it (ABCDEF is not allowed). You can scan the QR code (for Android&iPhone) to download the APP, then follow the APP prompt to scan the SN's QR code step by step. The device can be successfully added only if the P2P's status is online. You can also go to Main Menu - Configuration-Network Settings - Platform Settings to scan and add the device.

- Set the HDD. The newly installed hard disk needs formatting before it could be used. Choose the target HDD and click "int" to format it, then the status will show "Normal".
- Follow the guide of the Wizard to configure other settings.
Note: Picture is for reference only, please consult with the real products.
4.4 Login and Logout
User Login: You have to log in to the device before operating the menu and other functions. You can use the patterns to unlock or select the User Name in the drop-down list and input Password, then click OK to log in.

Note: If you enter the wrong password 7 times in the Login dialog box, the current user account will be locked for 60 seconds.
User Logout: After logging out, the monitor turns to the live view mode and if you want to perform any operations, you need to enter user name and password log in again. Click Menu > Shutdown to enter into the Shutdown menu, and then click Logout. After you have logged out the system, menu operation on the screen is invalid. It is required to input a user name and password to unlock the system.
Note: If you don't want to input password every time, you can disable the password. Go to Menu > Configuration > General> Enable Password and choose disable.
4.5 Network Settings
Network settings must be properly configured before you operate NVR over network. Make sure that the NVR has connected to the router by using the network cable and your network at home is in good condition. You can go to Menu > Configuration > Network to enter into the interface of Network Settings.

- Select the General tab.
- In the General Settings interface, you can configure the following settings: NIC Type, IPv4 Address, IPv4 Gateway, MTU and DNS Server. If the DHCP server is available, you can check the checkbox of DHCP to automatically obtain an IP address and other network settings from that server.
- After having configured the general settings, click the Apply button to save the settings.
- Click "Platform Access", make sure that the status of P2P shows "Online", which means your network status is in good condition, then you can watch the video normally on your mobile phone and PC.
4.6 Camera Management Setting
Enter Main Menu > Camera to configure the camera management, you can set the image, PTZ, motion, video loss and so on. For example, you can click OSD to change the name of your camera.

4.7 Adding IP Cameras
Before you can get a live view or record of the video, you should add the network cameras to the connection list of the device. Ensure the network connection is valid and correct, and the IP camera to add has already been activated. Please refer to the User Manual for activating the inactive IP camera.
Steps:
- Select the Add IP Camera option from the right-click menu in live view mode or click Menu> Camera > Camera to enter the IP camera management interface.

- The online cameras with same network segment will be detected and displayed in the camera list.
- NVR will automatically assigned IP address to IP cameras. If IP camera support same protocol as NVR (default protocol is IPCAM), the camera will be added automatically.
- If IP camera support other protocol, it need add manually. For example, there is an IP camera support ONVIF, it's IP address is 192.168.0.47, we choose to use D8 channel to add it. You can change "Adding Method" to Manual, edit the IP address to 192.168.0.47, change "Protocol" to ONVIF, the management port will change automatic, then click "OK" to add.
- For the successfully added IP cameras, the Security status shows the security level of the password of camera: strong password, weak password and risk password. For the successfully added IP cameras, the status shows
and means you can play the live video.
4.8 Live View
Some icons are provided on screen in Live View mode to indicate different camera status. In the live view mode, there are icons at the right top of the screen for each channel, showing the status of the record and alarm in the channel, so that you can find problems as soon as possible.

| Icon | Explanation |
|---|---|
| Indicating that there is an alarm or are alarms. Alarm includes video loss, tampering, motion detection or sensor alarm, etc. | |
| Recording (manual record, continuous record, motion detection or alarm triggered record) | |
| Alarm & Recording | |
| Event/Exception (event and exception information, appears at the lower-left corner of the screen.) |
You can change NVR's output resolution to 1080p or 4K for better experience if your monitor support. In NVR, goes to the Main Menu>Configuration>General> General>VGA/HDMI Resolution, change the output resolution from default 1024*768HZ to 1920*1080HZ or other choice you want. Note: Please make sure your monitor support 1080P or higher resolution, otherwise the picture on your monitor will not be displayed properly.
4.9 Recording Settings
NVR can set the continuous recording or motion detection video by one-click, and also set the recording schedule to record. Make sure that the disk has already been installed before you start. If not, please install a disk and initialize it. Make sure the status of HDD shows "Normal".
Purpose: Two kinds of record types are introduced in the following section, including Instant Record and All-day Record. And for other record types, you may refer to the user manual for detailed information. After rebooting all the manual records enabled are canceled.
4.9.1 Instant Recording
On the live view window of each channel, there is a quick setting toolbar which shows on the bottom of the window when you click on it. Click the
icon to enable the record, and the icon turns to
, then the icon turns to
. And click icon to
disable.
4.9.2 All-day Recording
Steps:
- On the live view window, right click the window and move the cursor to the Start Recording option, and select Continuous Record or Motion Detection Record on your demand.
- And click the Yes button in the pop up attention message box to confirm the settings. Then all the channels will start to record in the selected mode.
4.9.3 Set the recording schedule to record
Set the record schedule, and then the camera will automatically start/stop recording according to the configured schedule. You can go to Menu> Record> Schedule enter into the interface of Record Schedule.

Different recording types are marked in different color icons.
- 【Continuous】: scheduled recording.
- 【Event】: recording triggered by all event triggered alarm.
- 【Motion】: recording triggered by motion detection.
- 【Alarm】: recording triggered by alarm.
- 【M/A】: recording triggered by either motion detection or alarm.
- 【M&A】: recording triggered by motion detection and alarm.
Steps:
- Choose the camera you want to configure in the Camera drop-down list.
- Check the checkbox of Enable Schedule.
- Configure the record schedule.
Draw the schedule:
- Click on the color icon to select a record type in the event list on the right-side of the interface.
- Click and drag the mouse on the schedule.
- Click on the other area except for the schedule table to finish and exit the drawing. You can repeat step 1-3 to set schedule for other channels. If the settings can also be used to other channels, click Copy, and then choose the channel to which you want to copy.
- Click Apply in the Record Schedule interface to save the settings.
Note: Up to 8 periods can be configured for each day. And the time periods cannot be overlapped with each other; To enable Event, Motion, Alarm, M | A (motion or alarm) and M & A (motion and alarm) triggered recording, you must configure the motion detection settings, alarm input settings or VCA settings as well; The VCA settings are only available to the smart IP cameras.
4.10 Playback
The recorded video files on the hard disk can be played back in the following modes: instant playback, all-day playback for the specified channel, and playback by normal/event/smart/tag/sub-periods/external file search.
Playing Back by Normal Search:
Steps:
- Enter playback interface. Click Menu> Playback or select Playback from the right-click menu.
- Check the checkbox of channel(s) in the channel list and then double-click to select a date on the calendar. Note: If there are record files for that camera in that day, in the calendar, the icon for that day is displayed as
. Otherwise it is displayed as
. - You can use the toolbar in the bottom part of Playback interface to control playing progress.
- Select the channel(s) you want to play back by checking the checkbox(s), or execute simultaneous playback of multiple channels.

Detailed Explanation of Playback Toolbar:
| Button | Operation | Button | Operation | Button | Operation |
|---|---|---|---|---|---|
| Audio on/Mute | Start/Stop clipping | 30s forward | |||
| 30s reverse | Add default tag | Add customized tag | |||
| Tag management | Speed down | Pause reverse play/ Reverse play/ Single-frame reverse play | |||
| Pause play/Play/ Single-frame play | Scaling up/down the time line | Speed up | |||
| Previous day | Next day | Full Screen | |||
| Exit | Stop | Digital Zoom | |||
| Save the clips | Process bar | Video type |
Note: The 14-01-2015 22:15:23--03-03-2015 09:49:37 indicates the start time and end time of the record files. The icon"
" represents normal recording (manual or schedule); "
" represents event recording (motion, alarm, motion | alarm, motion & alarm). Playback progress bar: use the mouse to click any point of the progress bar to locate special frames.
4.11 Backup
Please insert the backup device(s) into the device before you start. You can go to Menu>Export>Normal enter into the interface of Export and select the cameras to search. You can set search condition and click Search button to enter the search result interface.
- Set search condition and click Search button to enter the search result interface. The matched video files are displayed in Chart or List display mode.
- Select video files from the Chart or List interface to export.
- Export the video files.
4.12 Setting Motion Detection Alarm
Steps:
- You can go to Menu> Camera > Motion Detection enter into the interface of Camera Management and choose a camera you want to set up motion detection.
- Set detection area and sensitivity. Check
checkbox to enable motion detection, use the mouse to draw detection area(s) and drag the sensitivity bar to set sensitivity. And then click
to set alarm response actions. - Click Trigger Channel tab and select one or more channels which will start to record or become full-screen monitoring when motion alarm is triggered.
- Set arming schedule of the channel. Select Arming Schedule tab to set the channel's arming schedule.
- Click Linkage Action tab to set up alarm response actions of motion alarm.
- If you want to set motion detection for another channel, repeat the above steps.
4.13 Setting Email
Before configuring the Email settings, the NVR must be connected to a local area network (LAN) that maintains an SMTP mail server. The network must also be connected to either an intranet or the Internet depending on the location of the e-mail accounts to which you want to send notification.
Steps:
- You can go to Menu > Configuration > Network > General enter into the interface of Network Settings. Set the IPv4 Address, IPv4 Subnet Mask, IPv4 Gateway and the Preferred DNS Server in the Network Settings menu. Click Apply to save the settings.
- Select the Email tab to enter the Email Settings interface.
- Configure the following Email settings and click Apply button to save the settings.
- [Enable Server Authentication] (optional): Check the checkbox to enable the server authentication feature.
- [User Name]: The user account of sender's Email for SMTP server authentication.
- [Password]: The password of sender's Email for SMTP server authentication.
- [SMTP Server]: The SMTP Server IP address or host name (e.g.,smtp.gmail.com).
- [SMTP Port No.]: The SMTP port. The port used for gmail is 587, and it can be 25,465 or other port for different smtp server.
- [Enable SSL] (optional): Click the checkbox to enable SSL if required by the SMTP server (Login your Gmail mailbox, click and enable "SSL" and enter https://myaccount.google.com/security?pli=1#connectedapps, and then turn "Allow less secure apps" on).
- [Sender]: The name of sender.
- [Sender's Address]: The Email address of sender.
- [Select Receivers]: Select the receiver. Up to 3 receivers can be configured.
- [Receiver]: The name of user to be notified.
- [Receiver's Address]: The Email address of user to be notified.
- [Enable Attached Pictures]: Check the checkbox of Enable Attached Picture if you want to send email with attached alarm images. The interval is the time of two adjacent alarm images.
- [Interval]: The interval refers to the time between two actions of sending attached pictures.
- [E-mail Test]: Sends a test message to verify that the SMTP server can be reached.
5. Remote Control
5.1 Accessing by Mobile
Before you start to remote control, please make sure that the status of P2P shows "Online", which means your network status is in good condition, then you can watch the video normally on your mobile phone and PC.
- Open up your "Annke Vision" APP from Google Play or Apple Store, click "Register" to sign up for an account by your mobile phone number or email address, please click "Login" after you registered successfully. Note: Please select the correct country / region when you register an account, it cannot be changed once selected.
- Select "+" or click the icon "
" in the upper right corner to add a device. You can also scan the QR code at the bottom of the device to add or go to "Menu"→"Configuration" → "Network" interface to get the QR code. - Select the device to get real-time preview, click the icon "
" in the upper right corner to enter into the interface of function, you can playback, change settings and other functions. click "More" to check more information.

NOTE: For your security, an SN can only be added by one account. But an account can be used on multiple mobile phones.
5.2 Accessing by IE (Internet Explorer)
When you are at home or the device only works within LAN, you can login on IE browser through device's IP address. You can find the IP address of the device by SADP or just go to DVR's Main Menu > Configuration > Network > General. You can find the SADP software from our website: www.annke.com/pages/download-center.
Steps:
- Run the SADP software to search online devices, then double click IP address to web browser. Or just input it into web browser if you know the IP address.
- Enter the user name "admin" and password in the login interface, and click the Login button.
- Once you entered the home page, you can see the list of devices that has been added, and choose a device to start live view.
5.3 Accessing by Client Software (Guarding Vision)
You can view the live video and manage the camera with the client software Guarding Vision. Please download it from our official website www.annke.com/pages/download-center. Please follow the installation prompts to install the software. The control panel and live view interface of Guarding Vision are shown below.
Note: If you want to remote access by CMS, choose "Cloud P2P Device" and login your cloud account and see live view.
6. Technical Specifications
| Feature | Specification |
|---|---|
| Model Number | AE-DX31NB |
| Video Compression | H.265 Pro+/H.265 Pro/H.265/H.264+/H.264 |
| Video Input | 32CH Analog Camera + 2CH IP Camera |
| Video Output | CVBS; VGA up to 1080p; HDMI up to 4K |
| Audio Input | 1-ch, RCA (2.0 Vp-p, 1 KΩ) / 32-ch via coaxial cable |
| Audio Output | 1-ch, RCA (Linear, 1 KΩ) |
| Supported Camera Types | TVI, AHD, CVI, CVBS & IP |
| IPC Recording & Playback | Up to 6 MP resolution |
| HDD Capacity | Up to 10 TB Capacity (per disk), options for 1TB, 2TB, 3TB, 4TB, None |
| HDD Interface | 2 SATA Interface, 3.5'' HDD Size, USB Interface Type |
| Network Interface | RJ45 X1 (10/100 M/1000 M self-adaptive Ethernet interface) |
| Max Playback Channel | 16CH |
| Human/Vehicle Analysis | Up to 32CH |
| DVR Power Supply | DC12V |
| e-Cloud (P2P) | Yes |
| Two-way Audio | No |
| Backup Type | Hard Drive |
| Supported Operating Systems | Microsoft Windows 2000, ME, XP, Vista, 98, 7, macOS |
| Supported Mobile Systems | iPhone OS, Android |
| IP Mode | Dynamic IP address |
| Wireless Security | WPA |
| Network Protocol | DDNS |
| Communication Interface | RS-485 |
| Video Adjustment | Auto White Balance |
| Video Resolution | 1080N |
| Video Standard | PAL |
| Video Input Interface | BNC (1.0 Vp-p, 75Ω) |
| Alarm Type | Email Photo |
| Smart Home Platform | Other |
| Certification | CE |
| USB Ports | USB 2.0*1, USB 3.0*1 |
6.1 HDD Storage Calculation Chart
The following chart shows an estimation of storage space used based on recording at one channel for an hour at a fixed bit rate.
| Bit Rate | Storage Used (per hour) |
|---|---|
| 96K | 42M |
| 128K | 56M |
| 160K | 70M |
| 192K | 84M |
| 224K | 98M |
| 256K | 112M |
| 320K | 140M |
| 384K | 168M |
| 448K | 196M |
| 512K | 225M |
| 640K | 281M |
| 768K | 337M |
| 896K | 393M |
| 1024K | 450M |
| 1280K | 562M |
| 1536K | 675M |
| 1792K | 787M |
| 2048K | 900M |
| 4096K | 1.8G |
| 8192K | 3.6G |
| 16384K | 7.2G |
Please note that supplied values for storage space used is just for reference. The storage values in the chart are estimated by formulas and may have some deviation from actual value.
7. Troubleshooting (FAQ)
7.1 What should I do if I forgot the NVR's password?
Option 1: Using Security Questions or GUID files
- If you forgot your password, please click "Forgot Password" in the lower left corner of the login interface.
- You can use the three preset security questions or use the GUID files to set a new password and reactivate the device.
Option 2: Using SADP Tool
- If you forget the answers for the questions and don't have GUID files, please use SADP to export the configuration files to reset the password.
- Download SADP from the CD or the website: www.annke.com/SADPTool.exe and install it on your computer. Make sure your computer and your device are in the same network.
- Open SADP and check the target device, click "Forgot Password" to enter the Reset Password interface.
- Click "Export" to download the key request file, and set the file path in the pop-up window.
- Click "Select Folder" to save the device's key request file on your PC. The exported key request file is a XML file which is named in the form of "Device Serial No.-System Time". Note: If your exporting fails, please right-click on SADP and run it as an administrator.
- As the file has a valid period, please send an email to support@annke.com immediately after exporting the file, and let us know that you have forgotten the password. Our technical engineer will send you a key file back. Please don't restart the DVR after the file is exported, otherwise the file will immediately become invalid.
- Select "Import File" as the resetting method. Click the file icon to select the received key file (XML file) and click "Open". Input a new password twice, and the system will evaluate the password strength automatically. We highly recommend you to use a strong password to ensure your data security. Lastly, click "Confirm" to finish your resetting.
7.2 What should I do when Mobile phone can not watch the video online?
Please go to the "Main Menu" > "Configuration"> "Network"> "Platform Access" to check the status of your network. If the NVR's P2P status is displayed online, you can add a device to "ANNKE Vision" APP to view it remotely. If you can not view it, please check the following steps:
(1). Please check the NVR's P2P status is offline or not, if it is offline:
- Please confirm whether the network cable is correctly connected to the router, or replace the network cable.
- If DHCP is enabled on the router, check whether DHCP is enabled on the NVR and whether the IP address of the same network segment as the router is obtained. If the router is set to a static IP address, fix the IP address of the NVR manually and pay attention to the DNS Address can not be empty.
(2). If it is not the problem of NVR offline, please check your mobile phone network is Normal or not.
7.3 What should I do when I add the device to the phone, but the device has already been added?
For your security, a device can only be added by one account, if you forget to register an account and password of mailbox, please take a photo of label at the bottom of the device and e-mail it to support@annke.com to unbind, and then you can rebind to the new account.
7.4 What should I do when NVR shows no picture in single or multiple camera channels?
Please make sure NVR, power supplies, cables, cameras and any part or parts is damaged or not may result in NVR shows no picture. Please use the replacement method to check which part is the cause of the problem:
- Please check all parts of the connection, whether it is loose or poor contact caused by no picture;
- Please replace the camera to see if the picture can be displayed;
- Please replace the cable to see if the picture can be displayed;
- Please replace the power to see if the picture can be displayed;
- Please replace the NVR channel to see if the picture can be displayed.
7.5 What should I do if the interface of the NVR monitor can not be operated?
The default resolution of the NVR output to the monitor is 1024*768, and it can also be adjusted to 1920*1080 resolution. If the resolution of the monitor is too low or is not a standard monitor, the interface may not be displayed properly.
- Adjust the display screen ratio to see if it is normal after adjustment, and check the maximum resolution of the monitor;
- If the monitor supports adjusting the margins, you can move the picture down until you can control the main menu, then you can enter the "Main menu" > "Configuration" > "General" > "VGA/HDMI Resolution" change to the appropriate resolution and save the setting;
- Connect the NVR and your computer to the same router, download and follow the IP search tool to login to the device by IP address and go to "Configuration">"System settings" > "Menu Output" > "VGA/ HDMI Resolution" to change to the appropriate resolution and save the setting.
7.6 Can I customize the display grid for fewer channels?
Yes, if you are using only 16 channels, you can alter the grid on the monitor to display only those 16 channels. The NVR's live view mode allows for channel switching, and the menu structure provides options for display settings.
8. User Tips
- Password Security: Always use a strong, memorable password (8-16 characters, including numbers, lowercase, uppercase, and special characters) for your device. Consider resetting it regularly for enhanced security.
- HDD Installation: Ensure the NVR's power is disconnected before installing or servicing the hard disk drive to prevent damage.
- Remote Access: For seamless mobile viewing, verify that the NVR's P2P status is "Online" in the network settings.
- Monitor Compatibility: To avoid display issues, ensure your monitor supports the NVR's output resolution (up to 1920x1080 or 4K).
9. Warranty and Support
Thank you for choosing ANNKE products. We prioritize your data safety and offer satisfactory service.
9.1 Contact Information
- Email Support: If you have any questions, please feel free to email us at support@annke.com.
- Help Center: Visit our help center at help.annke.com.
- Download Center: Download ANNKE App, Client software, and user manuals from our download center: https://www.annke.com/pages/download-center.
9.2 Manufacturer Information
- Manufacturer: Shenzhen Kean Digital co.,Ltd.
- Address: Room 1001, Rujun Building, No.105 Center Road, Bantian Street, Longgang District, Shenzhen, China. 518000
- Website: www.annke.com