SZRZGT Monochrome controller

Contents

SZRZGT DC5-24V Mini 11Keys RF Wireless LED Remote Controller User Manual

Model: Monochrome controller

1. Introduction

This RF Wireless LED Remote Controller is designed to provide convenient control over single-color LED light strips. It utilizes a 433MHz wireless signal for communication, offering a simple and effective way to adjust brightness and dynamic modes. This manual will guide you through the connection, operation, and maintenance of your controller.

Product overview video showing different controller variants and components.

2. Product Components

The package typically includes the following components:

  • RF Wireless Remote Control (11-key)
  • LED Controller Unit (various connection types available: bare wire, DC barrel, USB)
Various types of 11-key RF wireless LED remote controllers and their corresponding LED controller units.

Image showing different variants of the remote controller and LED controller units.

3. Setup Instructions

Follow these steps to connect your RF Wireless LED Remote Controller:

  1. Prepare Components: Ensure you have the RF remote, LED controller unit, LED light strip (e.g., SMD5050/3528/5730/3014), and a compatible power supply (DC 5-24V).
  2. Connect LED Strip to Controller: Connect your single-color LED light strip to the output side of the LED controller unit. Ensure correct polarity (positive to positive, negative to negative).
  3. Connect Power Supply to Controller: Connect your DC 5-24V power supply to the input side of the LED controller unit. The controller supports various input types:
    • Bare Wire: Connect the positive (+) and negative (-) wires from your power supply to the corresponding red and black wires on the controller.
    • DC Barrel: Plug the DC barrel connector from your power supply into the DC input jack on the controller.
    • USB: Plug the USB connector from your power supply (e.g., USB charger, power bank) into the USB input on the controller.
  4. Power On: Once all connections are secure, turn on the power supply. The LED light strip should illuminate, and the controller's indicator light may show activity.
  5. Remote Pairing (if necessary): Most RF controllers are pre-paired. If the remote does not respond, ensure the remote has a working battery. There is typically no manual pairing process for this type of simple RF controller; it should work out of the box.
Wiring diagram showing a power supply connected to the LED controller, which is then connected to an LED strip. The RF remote is shown wirelessly controlling the setup.

General wiring diagram for the LED controller and remote.

4. Operating Instructions

The 11-key RF wireless remote control allows for easy adjustment of your LED light strip. Refer to the button layout below for functions:

Diagram of the 11-key RF wireless remote control with labels for each button's function.

Remote control button functions.

  • ON/OFF (Red Power Button): Turns the LED light strip on or off.
  • LIGHT (Green Button): Toggles between static illumination and dynamic modes.
  • BRIGHT + / BRIGHT - (Top Black Buttons): Increases or decreases the brightness of the LED light strip in static mode.
  • 100% / 50% / 25% (Middle Black Buttons): Sets the brightness to 100%, 50%, or 25% directly in static mode.
  • MODE + / MODE - (Blue Buttons, vertical): Cycles through 8 different monochromatic dynamic modes.
  • SPEED + / SPEED - (Blue Buttons, horizontal): Adjusts the speed of the current dynamic mode across 10 levels.

5. Maintenance

5.1. Remote Control Battery Replacement

The remote control is powered by a button cell battery (e.g., CR2025 or similar). To replace the battery:

  1. Locate the battery compartment on the back of the remote control.
  2. Slide or pry open the battery tray.
  3. Remove the old battery and insert a new one, ensuring correct polarity (usually positive side up).
  4. Close the battery compartment securely.

5.2. Cleaning

Wipe the remote control and controller unit with a soft, dry cloth. Do not use harsh chemicals or abrasive cleaners. Keep the devices dry and away from excessive moisture.

6. Troubleshooting

  • LED strip does not light up:
    • Check all power connections to ensure they are secure and have correct polarity.
    • Verify the power supply is working and provides the correct voltage (DC 5-24V).
    • Ensure the LED strip itself is functional.
    • Press the ON/OFF button on the remote.
  • Remote control not responding:
    • Ensure the remote control has sufficient battery power. Replace the battery if necessary.
    • Check that the remote is within the effective operating range (up to 20 meters).
    • Minimize obstructions between the remote and the controller unit.
    • Avoid strong signal interference from other RF or wireless devices nearby.
    • If the issue persists, try restarting the power to the LED controller unit.
  • Connection failure or abnormal behavior:
    • Restart the LED controller unit by disconnecting and reconnecting its power.
    • Ensure the remote control has sufficient battery.
    • If the problem persists, refer to the official user manual PDF for more detailed troubleshooting or contact customer support.

Important Warnings:

  • The effective distance between the RF controller and the target device is usually around 10-20 meters, which may vary depending on the actual environment and obstacles.
  • Avoid signal interference: During operation, please try to avoid using other RF or wireless devices near the controller to prevent signal interference.
  • Ensure the RF controller has sufficient battery: Before use, it is recommended to ensure that the remote control has sufficient battery to avoid disconnection or malfunction.

7. Specifications

Feature Specification
Model 11-key RF monochrome controller
Working Temperature -20 to 60℃
Voltage DC 5-24V
Output Single Channel
Net Weight 35g
Dimensions (Controller) L86*W40*H7 mm
Static Power Consumption <1W
Maximum Load Current <6A
Output Power 5V<30W, 12V<72W, 24V<144W
Warranty 2 years
Certification CCC, CE, FCC, ROHS
Material ABS
Power Source DC
Remote Distance 20m
Applicable Lights SMD5050/3528/5730/5630/3014 LED strips
Controlled Method RF (Radio Frequency)
Origin Mainland China

8. Warranty and Support

This product comes with a 2-year warranty from the date of purchase. If you encounter any issues or require technical assistance, please contact the seller or manufacturer directly. For additional information, you may refer to the official user manual PDF:

View User Manual (PDF)

9. User Tips

  • For optimal performance, ensure the LED controller unit is not covered or obstructed, allowing for clear signal reception from the remote.
  • When installing, consider the placement of the controller to avoid direct exposure to extreme temperatures or moisture, which can affect its lifespan.
  • If using multiple controllers in close proximity, be aware that RF signals can sometimes interfere. Test each setup individually to ensure proper function.
  • Always double-check the voltage compatibility of your LED strip and power supply with the controller (DC 5-24V) to prevent damage.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.