Ziqqucu 10A 150W DC-DC Step-Down Module

Contents

DC-DC 10A High-Power Step-Down Constant Voltage Constant Current Power Module 150W User Manual

Model: 10A 150W DC-DC Step-Down Module | Brand: Ziqqucu

1. Introduction

This manual provides detailed instructions for the safe and effective use of the Ziqqucu 10A 150W DC-DC Step-Down Constant Voltage Constant Current Power Module. This non-isolated BUCK module is designed for a wide range of applications requiring precise voltage and current regulation.

Product Features:

  • Wide application range
  • Easy to use
  • Compact size
  • Stable performance
  • Over-temperature protection

2. Specifications

Parameter Value
Module Type Non-isolated Step-Down (BUCK)
Input Voltage 5-40V
Output Voltage 1-36V (Continuously Adjustable, default 5V)
Output Constant Current 0.3-10A (Adjustable, default 3A)
Dissipation Power 10A (Max)
Operating Temperature -40°C to +85°C (Enhanced heat dissipation recommended above 65°C)
Working Frequency 380KHz
Conversion Efficiency Up to 97% (Varies with input/output voltage, current, and voltage difference)
Short Circuit Protection None (Output)
Over-Temperature Protection Yes (Automatic shut-off)
Input Reverse Connection Protection No (User can add externally)
Module Dimensions (L x W x H) 67mm x 47mm x 27mm (2.63" x 1.85" x 1.06")
Installation Method 4 pieces of 2.5MM dart wire
Module dimensions showing length 6.7cm, width 4.7cm, and height 2.7cm.
Figure 1: Module Dimensions (Length: 6.7cm/2.63", Width: 4.7cm/1.85", Height: 2.7cm/1.06")
Detailed dimension drawing of the module, showing width 58mm, hole distance 37.5mm, hole distance 56mm, 67mm long, positioning hole diameter 2.6mm, and height 28mm.
Figure 2: Detailed Dimension Drawing (Width 58mm, Hole distance 37.5mm, Hole distance 56mm, 67mm long, Positioning hole diameter 2.6mm, Height 28mm)

3. Setup Instructions

3.1 Wiring

Connect the input power supply to the "IN" terminals and the load to the "OUT" terminals. Ensure correct polarity:

  • IN+: Input positive
  • IN-: Input negative
  • OUT+: Output positive
  • OUT-: Output negative

Important Safety Note: The module's current detection is low-end. Do NOT directly short-circuit the negative pole of the input and the negative pole of the output with a wire. This can damage the module.

This module is a step-down power supply, meaning it can only decrease voltage. The input voltage must always be higher than the desired output voltage.

Wiring and Adjustment Diagram showing input positive (IN+), input negative (IN-), output positive (+), output negative (-), output voltage regulation potentiometer, output current regulation potentiometer, and battery full indicator light adjustment potentiometer.
Figure 3: Wiring and Adjustment Diagram

4. Operating Instructions

4.1 Voltage Adjustment

To adjust the output voltage, turn the "CV-ADJ" potentiometer (Output Voltage Adjustment) on the power board:

  • Turn clockwise (to the right) to increase the voltage.
  • Turn counter-clockwise (to the left) to decrease the voltage.

4.2 Output Current Adjustment

To adjust the output constant current:

  1. Turn the "CC-ADJ" output current adjustment potentiometer counter-clockwise 10 full turns. This minimizes the output current to prevent damage during the next step.
  2. Connect a multimeter in series with the output, set to 20A or 10A current measurement mode. Short-circuit the output with the multimeter.
  3. Adjust the "CC-ADJ" potentiometer clockwise until the multimeter reads the desired output current.

4.3 Battery Full Indicator Light Adjustment

This adjustment is typically performed when using the module for battery charging:

  1. First, perform step 1 of the Output Current Adjustment (turn "CC-ADJ" counter-clockwise 10 turns).
  2. Connect a multimeter to the output in 20A or 10A current gear. Short-circuit the output with the multimeter and adjust the "CC-ADJ" potentiometer to the current you need when the battery is fully charged.
  3. If the LED2 light is on at this time, adjust the RV3 potentiometer (the middle potentiometer) counter-clockwise until the LED2 light turns off and the LED1 light turns on. This indicates the full indicator adjustment is complete.

5. Typical Applications

  • DIY regulated power supplies with constant voltage and constant current functions, offering load protection.
  • Powering various electronic devices.
  • Charging different types of batteries by setting appropriate charging voltage and current.
  • Utilizing solar panels to charge batteries, with constant current function to prevent overcharging.
  • Driving high-power LEDs, allowing for series and parallel combinations.
  • As a car power supply or charger for mobile phones and other digital products.

6. Maintenance

  • Heat Dissipation: The module's operating temperature range is -40°C to +85°C. For prolonged operation or when the module temperature exceeds 65°C, enhanced heat dissipation (e.g., additional heatsinks or active cooling) is strongly recommended to maintain stable performance and longevity.
  • Cleaning: Keep the module free from dust and debris. Use a soft, dry brush or compressed air for cleaning.
  • Connections: Periodically check all wiring connections to ensure they are secure and free from corrosion.

7. Troubleshooting

  • No Output:
    • Ensure input voltage is within the 5-40V range and is higher than the desired output voltage.
    • Check all wiring connections for correct polarity and secure contact.
    • Verify that the module is not in over-temperature protection mode (it will automatically shut off). Allow it to cool down if it's hot.
  • Incorrect Output Voltage/Current:
    • Re-perform the voltage and current adjustment procedures carefully using a calibrated multimeter.
    • Ensure the "CC-ADJ" potentiometer was turned fully counter-clockwise before setting the current to prevent damage.
  • Module Overheating:
    • Reduce the load current or input/output voltage difference.
    • Implement enhanced heat dissipation measures, such as larger heatsinks or a cooling fan, especially when operating at higher currents (e.g., above 6A) or in warm environments.
  • Damage from Short Circuit:
    • The module does not have output short-circuit protection. Avoid short-circuiting the output directly.
    • Do not short-circuit the negative poles of input and output.
  • Damage from Reverse Polarity:
    • The module lacks built-in input reverse connection protection. Always double-check input polarity. Consider adding an external anti-reverse diode if this is a concern for your application.

8. User Tips

  • Cooling for High Loads: Users have noted that the module's heatsinks can become very hot at higher currents (e.g., 6A). For continuous operation at or near maximum current, external cooling (such as a fan) is highly recommended to prevent overheating and ensure stable performance.
  • LED Indicators: The module features LED indicators for charging status. While the current setup uses red for both start and end of charge, understanding the adjustment procedure for the "Battery full indicator light" (Section 4.3) will help interpret its behavior.

9. Warranty and Support

For warranty information, technical support, or further assistance, please contact your point of purchase or the manufacturer directly. Keep your purchase receipt as proof of purchase.

A PDF version of this user manual is available for download: User Manual (PDF)

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.