Makerbase MKS DLC32 V2.1

Contents

Makerbase MKS DLC32 V2.1 Laser Engraving Machine Motherboard User Manual

32Bit Control Board with WiFi and TS24/TS35-R Display Support

1. Introduction

The Makerbase MKS DLC32 V2.1 is a high-performance 32-bit control board designed for laser engraving machines. It features an ESP32-WROOM-32U (8M Flash) chip, Xtensa dual-core 32-bit LX6 microprocessor, and supports clock frequencies up to 240 MHz. This board offers enhanced control and convenience for laser engraving tasks, including Wi-Fi connectivity, web control, mobile app support, and compatibility with TS24-R and TS35-R LCD offline displays.

MKS DLC32 V2.1 board with TS24-R and TS35-R displays

Figure 1: MKS DLC32 V2.1 control board with optional TS24-R and TS35-R displays.

2. Setup

2.1. Package Contents

Depending on the purchased package, your product may include the following components:

  • MKS DLC32 V2.1 Board: 1x MKS DLC32, 1x USB Cable.
  • MKS TS24-R V2.0 Display: 1x MKS TS24-R, 2x 10PIN 40CM flat cable.
  • MKS TS35-R V2.0 Display: 1x MKS TS35-R, 2x 10PIN 40CM flat cable.
  • Protective Shell: 1x MKS T-Armor, 1x MKS B-Armor, 4x Hexagon screw post M3*6, 4x M3 Hex nuts.
  • Motor Driver Packages: Various packages include the MKS DLC32 board, USB cable, and combinations of A4988 or TMC2209 motor drivers with heat sinks. Some packages also include TS24-R or TS35-R displays.

2.2. Hardware Overview

The MKS DLC32 V2.1 board integrates key components for laser engraving control. Familiarize yourself with the layout and connectors.

Top view of the MKS DLC32 V2.1 control board

Figure 2: Top view of the MKS DLC32 V2.1 control board.

Back view of the MKS DLC32 V2.1 control board

Figure 3: Back view of the MKS DLC32 V2.1 control board.

2.3. Wiring

Proper wiring is crucial for safe and correct operation. Refer to the detailed wiring diagram below for connecting motors, laser modules, endstops, and other peripherals.

Detailed wiring diagram for MKS DLC32 V2.1 showing connections for motors, laser, Z probe, endstops, power, USB, SD card, and displays.

Figure 4: MKS DLC32 V2.1 Wiring Diagram. Key connections include: Motor drive slots (X, Y1, Y2, Z), 12V/24V Output, Laser, Z Probe, Endstops, Buzzer, Spindle, Stepper Driver (for TB6600/TMC2160), Microstep settings, WiFi module, LCD interface, Reset button, SD Card slot, USB-PC interface, 12V/24V Input, Power fuse, Power switch interface, CNC principal axis, I2C interface, TS24/TS35 touch screen interface, and Runback button interface.

2.4. Firmware Update for TS24 Display

If you are using the TS24 display with the DLC32 motherboard, it is essential to refresh the firmware of the TS24 display before use to ensure compatibility and proper functionality. The firmware for the TS24 display can be found at the following GitHub link: https://github.com/makerbase-mks/MKS-DLC32/tree/main/MKS-DLC32-main/firmware/TS24

3. Operating Instructions

3.1. Offline Control with TS24/TS35 Displays

The MKS DLC32 V2.1 supports offline control via the TS24-R or TS35-R displays. These displays provide a user-friendly interface for controlling your laser engraving machine without needing a computer connection during operation.

MKS TS35-R V2.0 display interface showing status, position, power, speed, and control options.

Figure 5: MKS TS35-R V2.0 display interface for offline engraving.

MKS TS24-R V2.0 display interface showing control, setting, and engraving options.

Figure 6: MKS TS24-R V2.0 display interface for offline engraving.

3.2. Web Control

The MKS DLC32 V2.1 features a built-in web server (ESP32-WEB). By logging into the IP address of the motherboard with a browser on your local area network (LAN), you can perform various engraving operations, file transfers, and monitor the machine remotely.

Web control interface (ESP32-WEB) showing control, SD file management, settings, and language options.

Figure 7: Web control interface (ESP32-WEB).

3.3. Mobile App Control

Makerbase has developed a supporting mobile phone application that allows you to edit pictures, convert them into engraving files, and transfer them to the main board. This provides an additional layer of convenience for controlling your laser engraver.

Mobile app interface for controlling the laser engraving machine.

Figure 8: Mobile app interface.

3.4. Software Compatibility

The MKS DLC32 V2.1 is compatible with popular computer host software such as GRBLaser and Lightburn, offering flexibility in your workflow.

Screenshot showing GRBLaser and Lightburn software interfaces.

Figure 9: GRBLaser and Lightburn software compatibility.

3.5. Engraving Process

The MKS DLC32 V2.1 offers a delicate engraving effect with smoother grayscale expression due to its high PWM frequency (tens of KHz), which is significantly higher than traditional desktop engraving schemes (lower than 980Hz).

Example of an engraving effect achieved with MKS DLC32.

Figure 10: Example of engraving effect.

3.6. Video Demonstration

Watch this video for a comprehensive demonstration of the MKS DLC32 V2.1's features and operation:

Video 1: Demonstration of MKS DLC32 V2.1 features, including display operation, web control, and mobile app usage.

4. Maintenance

To ensure the longevity and optimal performance of your MKS DLC32 V2.1 control board, follow these general maintenance guidelines:

  • Keep Clean: Regularly clean the board and connectors to prevent dust and debris buildup, which can cause short circuits or overheating. Use a soft brush or compressed air.
  • Proper Storage: When not in use, store the board in a dry, anti-static environment.
  • Handle with Care: Avoid dropping or subjecting the board to physical shock.
  • Power Off Before Connecting/Disconnecting: Always power off the engraving machine and the control board before connecting or disconnecting any wires or components to prevent damage.

5. Troubleshooting

Here are some common issues and their potential solutions:

  • Display Issues (Striped/Mirrored Screen): If your TS24 or TS35 display shows a striped or mirrored image upon initial setup, it is likely due to a firmware mismatch. Ensure you have flashed the correct firmware for your specific display model (TS24-R V2.0 or TS35-R V2.0) onto the display. Refer to Section 2.4 for TS24 firmware.
  • Board Not Powering On/Burning Out: Double-check all power connections. Ensure the input voltage is within the specified range (12V-24V DC) and that the polarity is correct. A burned-out board often indicates incorrect power supply or a short circuit.
  • Wi-Fi Connectivity Problems: Ensure the Wi-Fi antenna is securely connected to the board. Verify that the board is within range of your Wi-Fi network. Check the network settings in the web interface or mobile app to ensure the correct SSID and password are entered.
  • Overheating Wi-Fi Module: While some heat is normal, excessive heat could indicate an issue. Ensure adequate ventilation around the board. If using a protective shell, ensure it allows for proper airflow.
  • Difficulty with Non-Laser Engraving Applications: The MKS DLC32 V2.1 is primarily designed for laser engraving machines. While it is a versatile control board, it may be challenging to adapt for other purposes without specific firmware or extensive configuration.

6. Specifications

The following table outlines the technical specifications of the MKS DLC32 V2.1 control board, comparing it with the MKS DLC model:

MKS DLC vs. MKS DLC32 Specifications
ItemMKS DLCMKS DLC32
Whole Size90*70mm90*70mm
Voltage12V-24V DC (<10A)12V-24V DC (<10A)
MCUATMEGA328P (8-Bit)ESP32-WROOM-32U (32-Bit)
MCU Freq.20MHz240MHz
Flash32KBytes8192KBytes
RAM32KBytes520KBytes
Laser Speed<3000mm/min<8000mm/min
Offline DisplayMKS TFT24/32/35MKS TS24-R/TS35-R
FirmwareGRBL
Serial DriverUSB (CH340)
Axis4 (X,Y1,Y2,Z)

Additional Specifications:

  • Item Type: Motherboard
  • High-concerned chemical: None
  • Package Dimensions: Approximately 10cm (Length) x 10cm (Width) x 10cm (Height)
  • Package Weight: Approximately 0.23 kg
Specifications table comparing MKS DLC and MKS DLC32

Figure 11: Detailed specifications comparison.

7. User Tips

  • The MKS DLC32 V2.1 is generally considered to offer excellent value for money and is a top-notch controller for its intended purpose.
  • Users have reported that the board performs reliably and "does what it's supposed to do."
  • Be aware that this board is specifically designed for laser engraving machines. While versatile, it might be challenging to adapt for other applications without specialized knowledge or firmware modifications.
  • Always verify the firmware version of your display (TS24-R or TS35-R) and update it if necessary to match the DLC32 board's requirements, especially if you encounter display anomalies like striped or mirrored screens.

8. Warranty & Support

For further technical documentation, firmware updates, and community support, please refer to the official Makerbase GitHub repository:

https://github.com/makerbase-mks/MKS-DLC32

A detailed user manual in PDF format may also be available. Please check the product page or the GitHub repository for the latest version of the user manual (PDF).


Documents and downloads

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.