WAAJEA LED Deck Lights

Contents

WAAJEA Ultrathin 6W Surface Mount LED Stair Step Light User Manual

Model: LED Deck Lights

Introduction

This manual provides detailed instructions for the safe installation, operation, and maintenance of your WAAJEA Ultrathin 6W Surface Mount LED Stair Step Light. Please read this manual thoroughly before installation and retain it for future reference.

Front and side view of the LED step light

Image: Front and side view of the LED step light, showcasing its slim profile.

Important Safety Directions

PLEASE READ CAREFULLY BEFORE INSTALLATION AND PRESERVE IT WELL. REPLACE ANY CRACKED PROTECTIVE SHIELD AND MUST BE INSTALLED BY A QUALIFIED ELECTRICIAN.

  1. Before starting the installation, please ensure to disconnect the power.
  2. Connect the Brown (Live) wire to the corresponding terminal on the terminal block marked L. Connect the Blue (Neutral) wire to the corresponding terminal on the terminal block marked N.
  3. Please don't look at the LED directly.
Installation instruction diagram with steps 1-6 and safety directions

Image: Detailed diagram illustrating the installation steps and safety warnings.

Setup and Installation

The LED Stair Step Light is designed for surface mounting (wall mounting).

Installation Steps:

  1. Prepare the Mounting Surface: Ensure the power is disconnected at the main circuit breaker before beginning.
  2. Mount the Base: Secure the light's base to the desired surface using appropriate screws. The light is designed for surface mounting.
  3. Wiring Connections:
    • Connect the Brown (Live) wire from your electrical supply to the terminal marked 'L' on the light's terminal block.
    • Connect the Blue (Neutral) wire from your electrical supply to the terminal marked 'N' on the light's terminal block.
    • Ensure all connections are secure.
  4. Attach the Light Fixture: Carefully attach the main light fixture to the mounted base, ensuring all wires are tucked in safely.
  5. Secure the Cover: Fasten the protective cover or front plate of the light.
  6. Test Operation: Once installation is complete, restore power and test the light's functionality.
Rear view of the LED step light showing wiring connections

Image: Rear view of the LED step light, illustrating the internal wiring compartment and connection points.

Dimensional drawing for A Type and B Type LED step lights

Image: Dimensional drawing showing the sizes for A Type (230mm x 80mm x 30mm) and B Type (225mm x 80mm x 30mm) models.

Operating Instructions

The LED Stair Step Light is designed for simple operation. Once properly installed and connected to a power source, it will illuminate when power is supplied. This light is not dimmable and does not feature a switch on the unit itself, relying on external power control (e.g., a wall switch).

Powering On/Off:

  • To turn the light ON, activate the external power switch connected to the fixture.
  • To turn the light OFF, deactivate the external power switch.

The light is available in various color temperatures: Warm white (2700K-3200K), Natural white (4000K), and White light (6000K-6500K), depending on the model purchased.

LED step lights installed on outdoor stairs, showing IP65 waterproof rating

Image: LED step lights illuminating outdoor stairs, demonstrating their application and IP65 waterproof capability.

Maintenance

To ensure optimal performance and longevity of your LED Stair Step Light, follow these maintenance guidelines:

  • Cleaning: Periodically clean the light fixture with a soft, damp cloth. Avoid using abrasive cleaners or solvents that could damage the finish or acrylic.
  • Inspection: Regularly inspect the light for any signs of damage, especially the protective shield. If the protective shield is cracked, it must be replaced to maintain the IP65 waterproof rating and ensure safety.
  • Electrical Connections: If you notice any flickering or inconsistent lighting, ensure the power is disconnected and check the electrical connections for tightness. This should only be performed by a qualified electrician.

Troubleshooting

If you encounter issues with your LED Stair Step Light, refer to the following common problems and solutions:

Problem Possible Cause Solution
Light does not turn on No power supply; Loose wiring connection; Faulty LED chip. Check power switch and circuit breaker. Ensure power is off, then check wiring connections (consult a qualified electrician). If issues persist, contact support.
Light flickers Loose wiring connection; Unstable power supply. Ensure power is off, then check wiring connections (consult a qualified electrician). Verify stable power supply.
Reduced brightness Dirt or debris on the light surface; Aging LED chip. Clean the light surface with a soft, damp cloth. If the problem persists, the LED chip may be reaching the end of its lifespan.

Specifications

Feature Detail
Product Name Surface Mounted LED Step Light
Light Source LED Chip
Power 6W
Input Voltage AC85-265V (50/60Hz) or DC12V
Emitting Color Options Warm White (2700K-3200K), Natural White (4000K), White Light (6000K-6500K)
Body Color Black (also Beige, White available)
Main Material Aluminum, Acrylic, LED, LED Driver
Size (A Type) 230mm x 80mm x 30mm
Size (B Type) 225mm x 80mm x 30mm
Waterproof Rate IP65
Installation Method Surface Mounted (Wall Mounting)
Luminous Flux 249-2000 Lumens
Certifications CE, RoHS
Warranty 2 years
Application Areas Kitchen, Dining Room, Bedroom, Foyer, Study, Bathroom, Staircase, Pathway, Yard, Stairs, Fences

User Tips

  • For optimal light distribution and safety on stairs, consider the placement of multiple lights to ensure even illumination without glare.
  • When installing outdoors, ensure all seals are properly seated to maintain the IP65 waterproof rating and protect against moisture ingress.
  • Regularly check the light's surface for any accumulation of dirt or leaves, especially in outdoor environments, to prevent obstruction of light output and maintain aesthetic appeal.
LED step lights illuminating an outdoor pathway

Image: LED step lights installed along an outdoor pathway, providing ambient lighting.

Warranty and Support

This WAAJEA LED Stair Step Light comes with a 2-year warranty from the date of purchase, covering manufacturing defects under normal use. Please retain your proof of purchase for warranty claims.

For further assistance, technical support, or detailed documentation, you may refer to the official user manual PDF available at: User Manual (PDF).

For any inquiries or support, please contact your retailer or the manufacturer directly.

Ask a question about this manual

Ask about setup, troubleshooting, compatibility, parts, safety, or missing instructions. Manuals+ will review the question and use this page’s manual context to help answer it.

After a successful submission, we securely hash the supplied account or form email before sending it to Microsoft Advertising for conversion attribution. Privacy details.